526329

LG VR6171LVM Handleiding

30
Verklein
Vergroot
Pagina terug
1/39
Pagina verder
OWNER’S MANUAL
CLEANING ROBOT
VR6170LVM
VR6171LVM
Before using, please carefully read the Safety Precautions pages to
allow for safe operation of the product. After reading the operation
manual, please keep it in an easily accessible location.
www.lg.com
ENGLISH
FRANÇAIS DEUTSCH ITALIANO
FEATURES
Images of the ceiling and floor are obtained from the sensors of the upper
and lower cameras, and through this, the location of HOM-BOT 2.0 will be
confirmed, therefore, elaborate cleaning can be accomplished for every part
of the room.
As the noise levels are at a quiet 60dB(A), cleaning can be performed at
night.
*60dB(A)
HOM-BOT 2.0 memorizes the location for cleaning.
* Minimizes the overlapping of cleaning area
The use of the ultra microfiber mop accessory allows finer dust to be
collected. (option)
The HOM-BOT 2.0 also has voice confirmation and instruction that can be
easily understood by the user.
The HOM-BOT 2.0 has two auto cleaning modes that can be selected by
the user.
*Spatial expantion mode, zigzag mode
Camera sensor
(upper, lower section)
“Please, check
the dust bin.”
ENGLISH
CONTENTS
Safety precautions
Included with product
Parts description
Button functions
Display status information
Before you start
Overview
1
BEFORE THE USE
2
METHOD OF USE
3
HANDLING METHOD AFTER USE
29~31
32
How to install the home station
How to turn the HOM-BOT 2.0 power supply on & off
How to start and stop cleaning
How to charge the battery
Cleaning modes
Auxiliary cleaning modes
Timer cleaning
Mop cleaning (option)
Location search function
Cleaning the dust bin
Cleaning the dust bin filter
Cleaning the brush
Cleaning the sensor/charging terminal
Cleaning the side brush
Cleaning the ultra microfiber mop (option)
4
ADDITIONAL INFORMATION
5
REFERENCE
2~4
5
6~7
8~9
10
11
12
13
14
15
16~17
18
19
20
21
22
23
24
25
26
27
28
Troubleshooting
Before you call for service
Product specifications
Open source software notice
33
34
2
SAFETY PRECAUTIONS
The purpose of the safety precautions described below is for the user to use the product safely and
correctly to prevent any unexpected risk of injury or damage.
Basic safety precautions
For your safety, do not remove the
battery from the HOM-BOT 2.0. If
you need to replace the battery or the
HOM-BOT 2.0, take it to the nearest
authorized LG Electronics service
center or dealer for assistance.
Failure to follow this warning can
cause fire or product failure.
Make sure the power cord of the
home station is not crushed under a
heavy object or damaged by contact
with sharp objects.
Failure to follow this warning can
cause electric shock, fire or product
failure. If the power cord is broken,
do not plug it in. Take the product
to an LG Electronics Authorised
service repairer.
Do not place the home station and
the HOM-BOT 2.0 near a heating
device.
Doing so can cause product
deformation, fire, or product failure.
Do not force the power plug to
bend. Do not use the power plug
when it has been damaged or
loosened.
Doing so can cause fire or product
failure.
Never use the HOM-BOT 2.0 with
a battery and/or home station from
any other product than the
HOM-BOT 2.0.
Doing so can cause fire or product
failure.
Do not use the HOM-BOT 2.0 when
candles or fragile objects are placed
on the floor.
Doing so can cause fire or product
failure.
Always use a dedicated outlet with
5A or above.
If multiple appliances are connected
to an outlet simultaneously, they
can generate enough heat to cause
a fire.
When pulling out the power plug,
always pull it out by grabbing the
plug, not the cord. When pulling out
the power plug, do not to touch the
prongs with your fingers.
Doing so can cause an electric
shock.
After reading this manual, please keep it in an easily accessible location.
This is the safety alert symbol. This symbol alerts you to potential hazards that can result in
property damage and/or serious bodily harm or death.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate
injury.
WARNING
WARNING
CAUTION
3
ENGLISH
SAFETY PRECAUTIONS
Do not touch the power plug with
wet hands.
Doing so can cause electric shock.
Do not spray or suck in inflammable
materials, surfactants, or drinking water
in the vicinity of the HOM-BOT 2.0.
Doing so can cause fire or product
failure.
* Inflammable materials: gasoline,
thinner, etc.
* Surfactant: detergent, articles for
bath, etc.
Do not insert any part of the body,
such as a hand or foot, below the
brush or wheels of the
HOM-BOT 2.0 while in use.
Doing so can cause injury or
product damage.
Do not operate the HOM-BOT 2.0
on narrow and high furniture such
as a wardrobe, refrigerator, desk,
table, etc.
Doing so can cause injury, product
failure or damage which is not
covered by the warranty.
Frequently empty the dust bin and
maintain its cleanliness.
The dust collected in the dust
bin can trigger allergies and may
contain harmful insects.
Use the HOM-BOT 2.0 indoors
only.
Using it outdoors can cause product
failure and irreparable damage to
the unit.
Close the cover of the dust bin on
the main unit before start cleaning.
If the cover is not closed, it can
cause injury or product damage.
Do not allow children or pets to play
with or rest upon the HOM-BOT 2.0
at any time. Do not use the HOM-BOT
2.0 while an object is hanging from it.
Doing so can cause injury or
product damage.
Turn the power supply off
immediately if any abnormal sound,
odor, or smoke is generated from
the HOM-BOT 2.0.
Failure to do so can cause fire or
product failure.
Do not operate the HOM-BOT 2.0
in a room where a child is sleeping.
Doing so can cause injury or
product damage.
Do not leave Children or pets near
the HOM-BOT 2.0 unsupervised.
Doing so can cause injury or
product damage.
Do not drop the HOM-BOT 2.0 or
subject it to strong impacts.
Doing so can cause injury or
product failure not covered by the
warranty.
Do not expose the HOM-BOT 2.0
to cold temperatures (less than
-5°C) for a long period of time.
Doing so can cause product failure.
Remove any cable or long string on
the floor.
Cable or string can get tangled in
the wheels of HOM-BOT 2.0 to
cause product failure or the cord
can be disconnected.
Gasoline
Detergent
WARNING
CAUTION
4
SAFETY PRECAUTIONS
Check the following items before use:
• Empty the dust bin after if fills up.
• Remove any cables or long strings from the floor.
• Remove any moisture from the floor before cleaning.
• Close the cover of the dust bin before cleaning.
• Remove fragile or unnecessary objects from the room to be cleaned.
For example, remove expensive ceramics and valuables from the floor.
• Confirm whether the battery has sufficient power, and if it is low, recharge it.
• Close the doors of any room that you do not want the HOM-BOT 2.0 to enter.
During cleaning, the HOM-BOT 2.0 may enter another room and continue cleaning.
• Do not use this product in the room where a child is sleeping alone. The child can be hurt.
• Remove towels, foot towel or any other thin cloth from the floor as they can get caught by the
brush.
• Cleaning will not proceed smoothly on carpets with tassels or carpets thicker than 8 mm
(0.315 in). It may be more convenient to arrange them before using the product.
CAUTION
In rare cases, the HOM-BOT 2.0’s
brush can damage the carpet. If
this happens, immediately stop the
cleaning operation.
When a carpet has long tassels, the
tassels can be damaged.
Do not let the main unit and
charging terminal of the home
station come into contact with
metallic objects.
Doing so can cause product failure.
Do not put water, detergent, etc.
into the HOM-BOT 2.0.
Doing so can cause product failure.
Do not put any water or detergent
on the HOM-BOT 2.0. If liquids get
inside of the HOM-BOT 2.0, turn off
the power supply and contact an LG
Electronics sales agent or customer
care center.
If the floor is wet or has wet spots,
wipe them up before using the
HOM-BOT 2.0. Do not use the
HOM-BOT 2.0 on a wet surface.
Failure to do so can cause product
failure.
When attaching the mop, do not
block the bottom camera sensor.
Blocking the bottom camera sensor
may not allow the product to work
smoothly.
Do not allow the HOM-BOT 2.0 to
sweep up liquids, blades, thumb
tacks, kindling, etc.
These items can cause product
failure.
Do not put sharp objects into the
opening of the HOM-BOT 2.0’s
supersonic sensor.
Doing so can cause product failure.
Do not use the HOM-BOT 2.0 when
the dust bin is completely filled up.
Doing so can cause product failure.
When the robot cleaner is
operating, it may hit the chair leg,
desk leg, table leg or other narrow
pieces of furniture.
For quicker and better cleaning,
place the dining chairs on top of the
dining table.
Tip
5
ENGLISH
INCLUDED WITH PRODUCT
 Figures can be different from actual objects.
Dust bin filter (spare)
Brush for cleaning filter Mop plate Ultra microfiber mop
(2 pieces) (option)
Dry cell for
remote controller
(2 units of AAA size)
Quick guide
Operation manual
Home station
HOM-BOT 2.0
www.lg.c om
QUICK GUIDE
CLEANING ROBOT
This guide briefly describes how to use the Cleaning Robot.
Fo r more detail, please refe r to the user manual
ENGLISH
FRANÇAIS
DEUTSCH DEUTSCH
OWNER’S MANUAL
CLEANING ROBOT
Before using, please carefully read the Safety Precautions pages to
allow for safe operation of the product. After reading the operation
manual, please keep it in an easily accessible location.
www.lg.com
ENGLISH
FRANÇAIS
DEUTSCH
DEUTSCH
Remote controller
6
PARTS DESCRIPTION - HOM-BOT 2.0
 Figures can be different from actual objects.
Plan view
Manipulation button
Dust bin cover button
Dust bin cover
Status indication lamp
Upper camera sensor
Detecting sensor of home station &
receiving sensor of remote controller
Ultrasonic sensor
Obstacle detecting sensor window
Ventilation port
Cliff detection sensor
Charging terminal
Brush
Side brush
Wheel
Lower camera sensor
Mop plate fixing hook
Battery
Power switch
Front view
Rear view
Bottom view
7
ENGLISH
PART DESCRIPTION – HOME STATION / DUST BIN
 Figures can be different from actual objects.
Home station
Dust bin
Remote controller holder
Charging terminal
Reset button
Sponge filter
HEPA filter
Dust bin handle
Dust bin cover
Suction port cover
Dust bin cover
opening button
Power cord fixing hook
8
BUTTON FUNCTIONS – HOM-BOT 2.0
• Use the TIMER button to start cleaning after a set amount of time has elapsed.
• The timer can be set from 1 to maximum of 12 hours in 1 hour units.
• When starting the timer clean outside of the home station, the cleaning time
can be reduced. Therefore use the product while attached to the home station
as much as possible.
• The timer setting is restricted if there is no dust bin.
• Press this button to change the cleaning mode.
• When the product is attached to the home station and when the timer is set,
spot cleaning mode cannot be selected.
Timer button
CLEAN MODE
button
HOMING button
START/STOP
button
• Press the START/STOP button to turn the HOM-BOT 2.0 on/off or start/stop
cleaning.
• Press the START/STOP button while the HOM-BOT 2.0 is on and it will
automatically start cleaning.
• If the START/STOP button is pressed during automatic cleaning, the HOM-BOT
2.0 will stop cleaning.
• Press and hold the START/STOP button for approximately two seconds to turn
off the HOM-BOT 2.0.
• If the button is pressed while in the timer mode, the reservation will be canceled.
• Press the HOMING button to move the HOM-BOT 2.0 to the home station for
battery charging.
• When cleaning is complete or the battery is low, the device will automatically
move to the home station to charge the battery even without pressing the
HOMING button.
9
ENGLISH
BUTTON FUNCTIONS – REMOTE CONTROL
• The HOM-BOT 2.0’s power supply cannot be turned on with the remote control.
• If the main unit is turned off, the remote control will not be activated.
• To turn on/off the power supply, use START/STOP button on the top of HOM-BOT 2.0.
• In order to do spot cleaning, timer cleaning, zigzag cleaning, and spatial expansion cleaning,
you must first stop the operation of the HOM-BOT 2.0.
Start
The HOM-BOT 2.0 will start
cleaning
Charging
The HOM-BOT 2.0 will move to the
home station for charging.
Timer
The timer can be set from 1-12
hours in the future. (Page 20)
Stop
If the HOM-BOT 2.0 is in operation
it will be stopped.
If it has been set for timer cleaning,
the reservation will be canceled.
Zigzag cleaning
Cleaning will be performed by
the HOM-BOT 2.0 in the zigzag
traveling fashion. (Page 18)
Spot Cleaning
Cleaning will concentrate
within a space of about 1 m
(3.28 ft). (Page 19)
Directional button
The HOM-BOT 2.0 will
move as desired by the
user: to front, rear, left, and
right sides for cleaning.
Cell by Cell cleaning
The HOM-BOT 2.0 will clean
using the spatial expansion
style.
(Page 18)
Tip
10
DISPLAY STATUS INFORMATION
• Once the cleaning mode is selected, it will be maintained even when the power is turned off.
• To cancel the timer setting, press the STOP button on the remote control or the START/
STOP button on the HOM-BOT 2.0.
Zigzag cleaning
• Indicates when the HOM-
BOT 2.0 is in zigzag
cleaning mode. (Page 18)
Timer icon
• This indicates when timer
cleaning has been set up.
(Page 20)
Battery and timer hour
indication
• While waiting for cleaning,
the remaining battery charge
will be shown.
• While waiting for timer
cleaning, the reservation time
will be shown.
• The state of the HOM-BOT
2.0 will be shown. (Page 17)
Spot cleaning
• Indicates when the
HOM-BOT 2.0 is in
spot cleaning mode.
(Page 19)
Spatial expansion
cleaning
• Indicates when the
HOM-BOT 2.0 is in
spatial expansion
cleaning mode.
(Page 18)
Battery icon
• Indicates when the
remaining charge
is displayed on the
section for battery
level, and flashes
when charging is
required. (Page 17)
Tip
11
ENGLISH
BEFORE YOU START
• Do not use this device in a room where a child is left alone. The child could be injured.
• Remove fragile or unnecessary objects from the room to be cleaned.
Especially, remove expensive ceramics and valuables from the floor.
• Close the cover of the dust bin before cleaning.
• Remove any moisture that might be on the floor.
• Remove cables, strips, towels, mat etc. from the floor so they will not get caught by the brush.
• Confirm whether battery charge is sufficient, and if it is low, recharge it.
• Empty the dust bin if it is full.
• Close the doors of any room that you do not want the HOM-BOT 2.0 to enter. During cleaning,
the HOM-BOT 2.0 may enter another room and continue cleaning.
• When the mop is attached, HOM-BOT 2.0 will not be able to go over thresholds of 5mm or higher.
If you are not planning to use the mop for cleaning, separate the mop before using HOM-BOT 2.0.
1. Open the battery cover by lifting the rear hook of the remote controller.
2. Insert two AAA batteries, checking for +, - nodes while loading.
3. Close the battery cover completely so that the batteries will not fall out.
• Only press one button at a time.
• Do not drop or subject it to forceful impact.
• Do not store it near devices that give off heat, fire or hot air.
• Certain fluorescent lamps, such as 3 wavelength fluorescent lamps, can interfere with the activation of the
remote control. Therefore, use it as far away as possible from such lamps.
• If the remote control is far from the HOM-BOT 2.0 when activated, it may fail to operate properly. Use the
device within 3 m (9.84 ft) of the HOM-BOT 2.0 if possible.
Check these items before cleaning
Loading the remote controller battery
Precautions while using the remote control
–
+
+
–
–
+
+
–
12
OVERVIEW
1
Install the home station. (Page 13)
Insert the power cord plug into an outlet and locate the
station against a wall. If power is not supplied to the
home station, the HOM-BOT 2.0 will not charge.
2
Turn on the power supply of the HOM-BOT 2.0.
(Page 14)
Turn on the power switch located on the bottom of
the HOM-BOT 2.0 and press the upper START/STOP
button to turn on the power supply.
※
If the power supply is not turned on, refer to page 14.
3
Check the dust bin.
Check the cleanness of the dust bin before start
cleaning and close the cover of the dust bin on the
main unit.
4
Start cleaning. (Page 15)
Press the START/STOP button once again while the
HOM-BOT 2.0 is turned on. You will hear the sound of
cleaning and cleaning will begin.
5
6
Automatic charge. (Page 16-17)
Use the cleaning mode and auxiliary functions.
(Page 18-22)
The HOM-BOT 2.0 will self-diagnose and automatically
return to the home station to recharge before the
complete discharge of the battery. It takes approximately
three hours to charge the battery.
With the HOM-BOT 2.0 and remote controller button,
the cleaning method and auxiliary functions can be used.
Zigzag or spatial expansion cleaning method can be
selected for the cleaning mode and manual cleaning,
spot cleaning, timer cleaning and micro fiber mop
cleaning can be selected for auxiliary function.
< Warning > When HOM-BOT 2.0 is operated with the cover of the dust bin open,
it can cause an injury or serious damage to the product.
Flickering
13
ENGLISH
HOW TO INSTALL THE HOME STATION
1. Position the home station against a wall, to prevent sliding during
docking, on hard level flooring.
Remove objects within 3 ft. to the right and left side and within
6 ft. to the front.
2. Plug the power cord into an outlet.
Wrap the power cord around the fixed hook on the back side of
the home station or along the wall surface so that the travel path
of the HOM-BOT 2.0 will not be obstructed.
3. Fix the home station against the wall so that it does not move.
4. When the remote controller is not used, store it on the remote
controller holder on the home station.
Fixing hook of power cord
• Always keep the home station plugged in. If the home station is not plugged in, the
HOM-BOT 2.0 will not return to the station to charge automatically.
How to Install the Home Station
< Warning > Do not operate the HOM-BOT 2.0 if it has a damaged cord or plug, if it is not working
properly, or if it has been damaged or dropped. To avoid hazard, the cord must be
replaced by LG Electronics, Inc. or a qualified service person.
Tip
14
HOW TO TURN THE HOM-BOT 2.0 POWER SUPPLY ON & OFF
To turn the power supply on, turn the HOM-BOT 2.0 upside down
on a smooth/soft surface and check whether the main power
supply switch is turned on.
※
Please make sure to remove the dust bin before flipping the
main body. Otherwise, the dust in the dust bin may fall out.
If the main power supply switch is turned off, turn on the switch.
※
When turning on the power switch, do not press the button
located at the upper section of the HOM-BOT 2.0. Operation of
the button can be delayed.
※
Turn off the power switch if the HOM-BOT 2.0 will not be used
for a long period of time, in order to protect the battery.
When the HOM-BOT 2.0 is not at the Home Station, and is in the
Stand by mode, press the ‘START/STOP’ button for more than
1 second. The HOM-BOT 2.0 will be turned on and a melody will
be sounded.
※
If the power supply is turned on and nothing is done for ten
minutes, the power supply will automatically turn off to reduce
battery consumption.
Press the START/STOP button for two seconds while the
HOM-BOT 2.0 is turned on. A melody will sound when the power
is turned off.
• If the power cannot be turned on, do the following.
- Turn on the power switch and wait for more than 3 seconds.
- Press the ‘START/STOP’ button when the power switch is turned on.
- If the power is not turned on or if there is no display but only the “Ting” sound, put
the HOM-BOT 2.0 on the home station.
- If there is no change even when HOM-BOT 2.0 is attached to the home station,
press the reset switch located on the rear side of the home station for 3 seconds
while the HOM-BOT 2.0 is attached on the home station.
Turning on the main power supply
Turning on from Stand By power.
Turning off the power supply
Tip
15
ENGLISH
HOW TO START AND STOP CLEANING
After the HOM-BOT 2.0 is turned on, press the START/STOP button
to begin cleaning. A melody will sound and cleaning will begin.
Press the START/STOP button during the cleaning cycle to stop
cleaning.
※
When the ‘START/STOP’ button is pressed while the power supply
of the HOM-BOT 2.0 is turned off, the power will be turned on.
Press the ‘START/STOP’ button one more time to start cleaning.
After the HOM-BOT 2.0 is turned on, press the START button on the
remote control. A melody will sound and cleaning will begin.
Press the STOP button during the cleaning cycle to stop cleaning.
※
The HOM-BOT 2.0 cannot be turned on from Stand By, by using
the remote control when the power of the HOM-BOT 2.0 is off.
When the power is off, press the ‘START/STOP’ button on the
upper side of HOM-BOT 2.0 to turn the power on and to allow the
remote to be used.
※
During cleaning, collisions can happen when the sensor cannot detect objects because of their shape (Thin
chair and table leg, furniture corner). When this happens, the internal impact detecting sensor will avoid
the obstacles by using a backward motion.
※
If the HOM-BOT 2.0 is set to start cleaning at a location away from the home station, put the device on
a flat floor in order to prevent a malfunction of the obstacle detecting sensor. In addition, start cleaning
from a location where there are not any obstacles such as curtains or walls within 30 cm (11.8 in) of the
HOM-BOT 2.0.
For best results:
• Briefly scan the area to be cleaned for big and small objects that will cause difficulty for the
HOM-BOT 2.0.
• If cleaning is started when the HOM-BOT 2.0 is at the home station, the device can rapidly
be returned to the home station as the current home position has been accurately read.
• For the safety of the HOM-BOT 2.0, a threshold of more than 10mm (0.4 in) cannot be
crossed.
• When the rag plate is installed, to prevent the 2
nd
contamination by the contaminated rag, it
cannot go over door sill of 5mm or higher.
Using the buttons on the HOM-BOT 2.0
Using the remote control
Tip
16
HOW TO CHARGE THE BATTERY
The HOM-BOT 2.0 returns to the home station at the end of a
cleaning cycle or when its battery is running low.
※
In the event that the unit returns to the Home Station due to
a low battery, cleaning will be started, after the charging, from
the nearest place of the area which has not been cleaned
before. (Page 17)
※
If HOM-BOT 2.0 is unable to dock to the home station on its
first attempt, it will try again until it docks successfully.
※
When HOM-BOT 2.0 completed all areas that it can clean, it
will return to the home station even when the battery level is
not low.
If using the HOM-BOT 2.0 for the first time or when charging the battery during cleaning, you can manually
charge the battery.
Method 1. Attach the HOM-BOT 2.0 to the home
station by aligning to the front side of the
home station. A melody sound will be
generated along with an audio message to
start charging.
※
If an audio message saying “Turn on the
main power switch on the bottom of the
unit” is generated repeatedly when the
HOM-BOT 2.0 is attached to the home
station, please check the power switch
and turn it on.
Method 2. When the HOMING button of the remote
control or the HOM-BOT 2.0 is pressed,
charging will start by automatically
generating a searching sound and returning
the HOM-BOT 2.0 to the home station.
※
If the HOM-BOT 2.0 does not start cleaning from the home station or if the HOM-BOT 2.0 is manually
charged by pressing the charge button, it may take slightly longer to find the home station.
※
If the HOM-BOT 2.0 stays within 10 cm (3.9 in) of the front of the charging terminal while the power
supply is turned on, it will automatically be returned to the home station and charging will begin.
Automatic charging
Manual charging
Take the following precautions when using the home station:
• If foreign material is caught in the charging terminal, charging may not proceed smoothly.
Wipe the terminal from time to time with a dry cloth after the power plug is disconnected.
• To prevent electric shock, do not touch the charging terminal with any metallic objects.
• To avoid fire or electric shock, never disassemble or modify the home station.
• Do not to place the home station or power plug near to a heating appliance.
Tip
17
ENGLISH
HOW TO CHARGE THE BATTERY
Check 1:
If the battery is not charging even when the HOM-BOT 2.0
is attached to the home station, check the following items.
- Turn the power switch on the bottom of the HOM-BOT 2.0
off once and then on again.
- Check the power lamp of the home station.
- Wipe the terminal on the home station with a dry cloth
Check 2:
If the battery is still not charging after the previous check,
try the following.
- Attach the HOM-BOT 2.0 to the home station.
- Press the reset button at the rear of the home station for
three seconds.
The remaining battery charge can be confirmed from the charge indication light, which will indicate charge
as follows:
• During charging, the charge remaining indication light will icker.
• When charging is completed at the home station, only the battery icon will illuminate to save power.
• The battery icon will icker when battery charging is required.
Full charging
(Under charging)
The status indication lamp
while the robot is charged
(In spatial expand mode)
High Middle Low Charging is
required
※
If there is still an area to be cleaned when the HOM-BOT 2.0
is returned to the home station for charging, the selected
cleaning mode is displayed.
- When the battery is fully charged, it cleans the area that
remains to be cleaned. (Perform 1 time)
- During charging, when the cleaning mode is displayed,
pressing the START button on the remote controller or
the START/STOP button on HOM-BOT 2.0 will cause the
HOM-BOT 2.0 to search for the un-cleaned area and start
cleaning.
- Pressing the mode selection button (ZIGZAG, CELL BY
CELL) will start the cleaning process from the beginning.
Remaining Battery Charge Indicator
If the Battery is Not Charging
Flickering
In the case of not
existing an area to
be cleaned
In the case of
existing an area
to be cleaned
(Flickering)
Charge
terminal
18
CLEANING MODES
With zigzag cleaning, total inside of the house will be
cleaned with the repetition of zigzag traveling.
If rapid cleaning is desired, use zigzag cleaning.
When pressing ‘ZIGZAG’ button of remote controller,
zigzag cleaning will be started while zigzag cleaning icon is
indicated at the state indication lamp.
With spatial expansion cleaning, the cleaning will be
performed by dividing the inside of the house into partial
square spaces.
If elaborate cleaning is desired, use spatial expansion
cleaning.
When pressing ‘Cell by Cell’ button of remote controller,
spatial expansion cleaning will be started while spatial
expansion cleaning icon is indicated at the state indication
lamp.
The 1st stage:
The maximum outline of 3m x 3m of cleaning area
will be cleaned. (The size of outline will be changed in
accordance with the shape of the house inside.)
The 2nd stage:
Inside of the outline will be cleaned with zigzag traveling.
When the 1st, 2nd stages are completed, the inside of
the house will be cleaned through the repetition of above
cleaning method as the device is being moved to the next
cleaning area.
• Once set up, the cleaning mode will be maintained even after the power supply is turned off.
• During operation, if a mode change is required, press the STOP button and then select the
mode.
Zigzag Cleaning
Spatial Expansion Cleaning
Tip
19
ENGLISH
AUXILIARY CLEANING MODES
This method of cleaning involves manually moving the HOM-BOT 2.0 by pressing the directional (arrow)
buttons on the remote control.
The interior space will be cleaned by the HOM-BOT 2.0 as it is being moved to the front, rear, or rotated to
the left and right side according to the input of the directional buttons.
If it meets an obstacle during manual cleaning (straight driving), it stops.
Use this cleaning method when concentrated cleaning of a small interior space is required.
After moving the HOM-BOT 2.0 to the location to be cleaned, press the SPOT button on the remote
control.
The spot cleaning icon will illuminate on the HOM-BOT 2.0, and concentrated cleaning will be performed
for a space within a radius of 1 m (3.28 ft).
※
During charging, the spot cleaning button on the remote control will not activate.
Manual cleaning
Spot Cleaning
It stops at the started position after
completing the cleaning(takes 4~5 min.).
20
TIMER CLEANING
1. By pressing the TIMER button on the remote control
or the HOM-BOT 2.0, a cleaning time can be
scheduled.
2. Adjust the time as much as desired by multiple
presses of the TIMER button. Each time you
press the button, the time will increase by one
hour.
- The start time can be set up to a maximum of
12 hours and once set up, the time in hours, will
be indicated by the status indication lamps.
3. After setting up the start time, press the START/STOP
button on the HOM-BOT 2.0 or wait about five seconds.
When the timer setting is complete, a melody will sound,
and the timer indicator will remain on.
- If the timer is set, timer icon of a clock shape is
displayed on the status indicator lamp.
Set the timer to schedule the cleaning and begin in 1-12 hours.
The timer setting is restricted if there is no dust bin.
• When the set up time elapses, cleaning will start automatically.
• Use the timer setting when the HOM-BOT 2.0 is attached to the home station. If the timer is
set while HOM-BOT 2.0 is away from the home station, the cleaning time can be shortened.
• To cancel the timer setting during the set up time, press the STOP button on the remote
control or the START/STOP button on the HOM-BOT 2.0.
1 hour
9 hours
6 hours
12 hours
Tip
21
ENGLISH
MOP CLEANING (OPTION)
1. Attach the ultra microfiber mop to the Velcro
of the mop plate as shown in the figure.
※
To prevent the HOM-BOT 2.0 from
malfunctioning, attach the mop so that the
mop attaching guide will not be covered by
the mop.
2. Accurately match up and insert the mop plate
fixing hook on the lower section of the
HOM-BOT 2.0 into the fixing groove of the
mop plate.
3. When you accurately match up and press the
mop plate to the rear side of the HOM-BOT
2.0, it will mount with a clicking sound.
※
Be careful to properly mount the mop plate,
or it can separate during cleaning.
For mop cleaning, mount the mop and mop plate to the HOM-BOT 2.0 according to the following instructions:
By attaching the ultra microfiber mop, you can
effectively use the HOM-BOT 2.0 to remove dust.
When the mop plate is attached, the HOM-BOT 2.0
will not climb on to carpets or over thresholds, in
order to prevent transferring dirt from the mop.
• To avoid odors, wash any foreign material or dust off the mop after cleaning is complete.
• To avoid staining floors, do not use the ultra microfiber mop to clean when dirt is mixed with
liquids such as coffee or ink.
• To avoid damage to carpets from the Velcro or dirt transfer from the mop, do not clean the
carpet while the mop plate or mop is attached.
• Keep the ultra microfiber mop dry. Do not use it on wet surfaces.
If there is moisture, it can interfere with the navigation.
Ultra microfiber mop
Mop plate
Mop plate
Fixing hook
Fixing groove
“Click!”
Ultra microfiber mop
Ultra microfiber mopUltra microfiber mop
Mop fixing section With mop attached
Bottom camera sensor
Tip
22
LOCATION SEARCH FUNCTION
When the user removes any abnormal condition of
HOM-BOT 2.0 or moves the location arbitrarily, the
location search function will activate.
1. Locate HOM-BOT 2.0 near the location where
HOM-BOT 2.0 was moved.
※
Location search is more effective when HOM-
BOT 2.0 is closer to the location where it was
moved.
※
If it goes out of diameter of 1m from the
occurrence position, it becomes difficult to
search the position.
2. Press the START/STOP button on HOM-BOT 2.0 or START button on the remote controller.
HOM-BOT 2.0 will start the location search function along with an audio guide.
※
When the location search is successfully completed, it will continue to the cleaning from where it was
moved.
If position search fails, it will start again from the beginning by pressing remote control mode button or
if cleaning mode is changed.
HOM-BOT 2.0 remembers its location while cleaning.
If the user moves the HOM-BOT 2.0 while it is operating, it will search its location with
the location search function to continue from previous location.
Change location
Location of incident
Location of incident
1m
1m
When the location search
function is activated, the
cleaning mode of the status
indicator will flash
Checking current location.
• When the power is turned off after the location search function is set, the location search
function will be canceled.
• Location search is more effective when HOM-BOT 2.0 is closer to the location where it was
moved.
• After position search function is set, if timer is set or it is recharged, then the setting will be
cancelled.
Tip
23
ENGLISH
CLEANING THE DUST BIN
1. Open the dust bin cover by pressing the PUSH
button on the HOM-BOT 2.0.
2. Grab the handle of the dust bin and pull it
upward.
3. Separate the HEPA filter and the inside sponge
filter by removing the HEPA filter
※
To clean the dust bin lter, refer to page 24.
4. Lift the cover upward while pressing the
separation button on the dust bin.
5. Empty the dust bin and clean it with a cleaning
brush or under running water.
6. After cleaning with water, completely dry the
dust bin in a well-ventilated area out of the direct
sunlight.
7. When you have completed cleaning the dust bin,
close the cover and replace the sponge filter and
HEPA filter.
8. Put the dust bin into the HOM-BOT 2.0 and
close the dust bin cover.
If the dust bin is full, suction power can be weakened. Clean the dust bin before and after each cleaning
session. Clean the dust bin using the following sequence:
• After cleaning, always mount the dust bin filters (HEPA filter, sponge filter) to the dust bin.
If they are not mounted, dust may enter the HOM-BOT 2.0 interior and cause product failure.
• After cleaning the dust bin, make sure to start the operation with the dust bin installed.
If it is operated without the dust bin, voice message, “please check the dust bin” will sound.
Tip
24
CLEANING THE DUST BIN FILTER
The dust bin filters are comprised of the HEPA filter and the sponge filter.
Clean the HEPA filter and the sponge filter according to the following sequence:
1. Separate the HEPA filter and the inside sponge
filter by removing the HEPA filter (as shown).
3. After washing the HEPA filter and the sponge
filter with water, place them out of direct sunlight
and allow them to dry completely.
4. Mount the cleaned HEPA lter and sponge lter
into the dust bin according to the sequence
shown to the right. When assembling the filter,
the filter handle should face upward.
2. Carefully clean any fine dust off the HEPA filter and
the sponge filter with a vacuum cleaner or water.
• In order to maintain the performance of the HOM-BOT 2.0, the HEPA filter should be
cleaned with a cleaning brush or vacuum cleaner at least once a week, and should be washed
under running water at least once a month.
Tip
25
ENGLISH
CLEANING THE BRUSH
Insert the fixing hook on the
opposite side of the brush
(marked with a rounded
rectangle) by matching it to
the separation groove of the
brush.
Insert the fixing guide in front
of the brush by matching it to
the fixing groove located on the
main unit.
Close the cover by pressing
it down until you hear a click
from the fixing hook.
※
Be careful that the side
brush is not caught by the
cover.
Grab the brush and remove
by pulling it up.
Clean the brush with a vacuum
cleaner, scissors, etc.
Insert the fixing hook on the
side of the brush (marked with
the square) by matching it to
the fixing groove of the brush.
Lay a smooth cloth on the
floor. Turn the HOM-BOT 2.0
over and put the HOM-BOT
2.0 on the cloth. Turn off the
power switch before cleaning.
Separate the cover by pressing
the fixing hook and pulling
upward.
Wearing gloves turn the brush
until the separation groove of
the brush appears.
The brush, located on the bottom of the HOM-BOT 2.0, helps with the suction of foreign objects. Perform
the following steps to clean the brush:
※
Please make sure to remove the dust bin before flipping the main body.
Otherwise, the dust in the dust bin may fall out.
Separation
groove of
brush
26
CLEANING THE SENSOR/CHARGING TERMINAL
Receiving sensor of
remote controller
Camera sensor
• Do not clean the HOM-BOT 2.0 by directly spraying it with water, thinner, benzene, etc.
• Call the service center if the sensor or charging terminal is damaged. Sensor and terminal
damage can cause the product to malfunction.
There are sensors on the HOM-BOT 2.0 that can detect obstacles,
stairways and the home station for charging the battery. In order to
maintain the performance of the HOM-BOT 2.0, regularly clean the sensors
and charging terminal as follows:
1. Lay a smooth cloth on the floor, overturn the HOM-BOT 2.0 and put it on
the cloth.
※
Please make sure to remove the dust bin before flipping the main body.
Otherwise, the dust in the dust bin may fall out.
2. Turn off the power switch on the bottom of the HOM-BOT 2.0. Injury can
be caused by the activation of the HOM-BOT 2.0 if the main power is
not turned off.
3. Use a smooth cloth or cleaning brush to wipe the dust off each sensor
and the charging terminal as described below.
Charging
terminal
Obstacle detection sensor
Cliff detection sensor
Charging terminal
Bottom camera
sensor
Lens
Tip
27
ENGLISH
CLEANING THE SIDE BRUSH
Foreign objects/materials such as hair can easily adhere to the side
brush. Remove such materials at least once a week.
If excessive amounts of foreign materials are stuck to the brush,
there is the risk of damage to the brushes.
If the floor is rough or walls are frequently cleaned, the side brush may bend or become damaged. In this
case, use the following method to straighten the side brush.
1. The following procedure is helpful in restoring
deformed brushes.
2. Turn off the power supply by pressing the
START/STOP button on the HOM-BOT 2.0 for
two seconds.
3. Place the HOM-BOT 2.0 at the end of a table to
make cleaning the side brush easier. Make sure
that the HOM-BOT 2.0 is not in danger of falling.
4. Soak the side brush in warm water.
5. Press down on the side brush for about ten
seconds so that it is completely submerged in
the water.
6. Slowly wipe the side brush by sliding it through
your hand.
7. Rotate the side brush and repeat steps 4-6 for
each section of the brush.
8. Use the side brush only after it has completely
dried.
28
CLEANING THE ULTRA MICROFIBER MOP (OPTION)
1. Separate the ultra microfiber mop from the mop plate.
2. Carefully clean it with water.
3. Use the mop only after allowing it to dry completely in a
sunny, well-ventilated area.
To avoid odors, dirt and dust should be washed off the mop after it is used for cleaning. Follow these
directions to wash the ultra microfiber mop:
• To avoid product malfunction, only use the ultra microfiber mop provided with
the HOM-BOT 2.0.
• Additional microfiber mops can be purchased by visiting a nearby LG Electronics service
center.
Tip
… 30 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw LG VR6171LVM bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van LG VR6171LVM in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 87,07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info