526328

LG VR6170LVM Handleiding

24
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
OWNER’S MANUAL
CLEANING ROBOT
VR6170LVM
Before using, please carefully read the Safety Precautions pages to
allow for safe operation of the product. After reading the operation
manual, please keep it in an easily accessible location.
www.lg.com
FEATURES
Images of the ceiling and floor are obtained from the sensors of the upper
and lower cameras, and through this, the location of Roboking 2.0 will be
confirmed, therefore, elaborate cleaning can be accomplished for every part
of the room.
As the noise levels are at a quiet 60dB(A), cleaning can be performed at
night.
*60dB(A)
Roboking 2.0 memorizes the location for cleaning.
* Minimizes the overlapping of cleaning area
The use of the ultra microfiber mop accessory allows finer dust to be
collected from hard flooring. (option)
The Roboking 2.0 also has voice confirmation and instruction that can be
easily understood by the user.
The Roboking 2.0 has two auto cleaning modes that can be selected by the
user.
*Spatial expantion mode, zigzag mode
Camera sensor
(upper, lower section)
“Please, check
the dust bin.”
CONTENTS
Safety precautions
Included with product
Parts description
Button functions
Display status information
Before you start
Overview
1
BEFORE THE USE
2
METHOD OF USE
3
HANDLING METHOD AFTER USE
29~31
32
How to install the home station
How to turn the Roboking 2.0 power supply on & off
How to start and stop cleaning
How to charge the battery
Cleaning modes
Auxiliary cleaning modes
Timer cleaning
Mop cleaning (option)
Location search function
Cleaning the dust bin
Cleaning the dust bin filter
Cleaning the brush
Cleaning the sensor/charging terminal
Cleaning the side brush
Cleaning the ultra microfiber mop (option)
4
ADDITIONAL INFORMATION
5
REFERENCE
2~4
5
6~7
8~9
10
11
12
13
14
15
16~17
18
19
20
21
22
23
24
25
26
27
28
Troubleshooting
Before you call for service
Product specifications
Open source software notice
33
34
2
SAFETY PRECAUTIONS
The purpose of the safety precautions described below is for the user to use the product safely and
correctly to prevent any unexpected risk of injury or damage.
Basic safety precautions
For your safety, do not remove the
battery from the Roboking 2.0. If you
need to replace the battery or the
Roboking 2.0, take it to the nearest
authorized LG Electronics service
center or dealer for assistance.
Failure to follow this warning can
cause fire or product failure.
Make sure the power cord of the
home station is not crushed under a
heavy object or damaged by contact
with sharp objects.
Failure to follow this warning can
cause electric shock, fire or product
failure. If the power cord is broken,
do not plug it in. Take the product
to an LG Electronics Authorised
service repairer.
Do not place the home station and
the Roboking 2.0 near a heating
device.
Doing so can cause product
deformation, fire, or product failure.
Do not force the power plug to
bend. Do not use the power plug
when it has been damaged or
loosened.
Doing so can cause fire or product
failure.
Never use the Roboking 2.0 with a
battery and/or home station from
any other product than the
Roboking 2.0.
Doing so can cause fire or product
failure.
Do not use the Roboking 2.0 when
candles or fragile objects are placed
on the floor.
Doing so can cause fire or product
failure.
Always use a dedicated outlet with
5A or above.
If multiple appliances are connected
to an outlet simultaneously, they
can generate enough heat to cause
a fire.
When pulling out the power plug,
always pull it out by grabbing the
plug, not the cord. When pulling out
the power plug, do not to touch the
prongs with your fingers.
Doing so can cause an electric
shock.
After reading this manual, please keep it in an easily accessible location.
This is the safety alert symbol. This symbol alerts you to potential hazards that can result in
property damage and/or serious bodily harm or death.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate
injury.
WARNING
WARNING
CAUTION
3
SAFETY PRECAUTIONS
Do not touch the power plug with
wet hands.
Doing so can cause electric shock.
Do not spray or suck in inflammable
materials, surfactants, or drinking water
in the vicinity of the Roboking 2.0.
Doing so can cause fire or product
failure.
* Inflammable materials: gasoline,
thinner, etc.
* Surfactant: detergent, articles for
bath, etc.
Do not insert any part of the body,
such as a hand or foot, below the
brush or wheels of the
Roboking 2.0 while in use.
Doing so can cause injury or
product damage.
Do not operate the Roboking 2.0
on narrow and high furniture such
as a wardrobe, refrigerator, desk,
table, etc.
Doing so can cause injury, product
failure or damage which is not
covered by the warranty.
Frequently empty the dust bin and
maintain its cleanliness.
The dust collected in the dust
bin can trigger allergies and may
contain harmful insects.
Use the Roboking 2.0 indoors only.
Using it outdoors can cause product
failure and irreparable damage to
the unit.
Close the cover of the dust bin on
the main unit before start cleaning.
If the cover is not closed, it can
cause injury or product damage.
Do not allow children or pets to play
with or rest upon the Roboking 2.0 at
any time. Do not use the Roboking 2.0
while an object is hanging from it.
Doing so can cause injury or
product damage.
Turn the power supply off
immediately if any abnormal sound,
odor, or smoke is generated from
the Roboking 2.0.
Failure to do so can cause fire or
product failure.
Do not operate the Roboking 2.0 in
a room where a child is sleeping.
Doing so can cause injury or
product damage.
Do not leave Children or pets near
the Roboking 2.0 unsupervised.
Doing so can cause injury or
product damage.
Do not drop the Roboking 2.0 or
subject it to strong impacts.
Doing so can cause injury or
product failure not covered by the
warranty.
Do not expose the Roboking 2.0 to
cold temperatures (less than -5°C)
for a long period of time.
Doing so can cause product failure.
Remove any cable or long string on
the floor.
Cable or string can get tangled in
the wheels of Roboking 2.0 and
cause product failure or the cord to
be disconnected.
Gasoline
Detergent
WARNING
CAUTION
4
SAFETY PRECAUTIONS
Check the following items before use:
• Empty the dust bin after if fills up.
• Remove any cables or long strings from the floor.
• Remove any moisture from the floor before cleaning.
• Close the cover of the dust bin before cleaning.
• Remove fragile or unnecessary objects from the room to be cleaned.
For example, remove expensive ceramics and valuables from the floor.
• Confirm whether the battery has sufficient power, and if it is low, recharge it.
• Close the doors of any room that you do not want the Roboking 2.0 to enter.
During cleaning, the Roboking 2.0 may enter another room and continue cleaning.
• Do not use this product in the room where a child is sleeping alone. The child can be hurt.
• Remove towels, foot towel or any other thin cloth from the floor as they can get caught by the
brush.
• Cleaning will not proceed smoothly on carpets or rugs with tassels or carpets thicker
than 8 mm (0.315 in). It may be more convenient to rearrange or remove them before using
the product.
CAUTION
In rare cases, the Roboking 2.0’s
brush can damage the carpet. If
this happens, immediately stop the
cleaning operation.
When a carpet has long tassels, the
tassels can be damaged.
Do not let the main unit and
charging terminal of the home
station come into contact with
metallic objects.
Doing so can cause product failure.
Do not put water, detergent, etc.
into the Roboking 2.0.
Doing so can cause product failure.
Do not put any water or detergent
on the Roboking 2.0. If liquids get
inside of the Roboking 2.0, turn off
the power supply and contact an LG
Electronics sales agent or customer
care center.
If the floor is wet or has wet spots,
wipe them up before using the
Roboking 2.0. Do not use the
Roboking 2.0 on a wet surface.
Failure to do so can cause product
failure.
When attaching the mop, do not
block the bottom camera sensor.
Blocking the bottom camera sensor
may not allow the product to work
smoothly.
Do not allow the Roboking 2.0 to
sweep up liquids, blades, thumb
tacks, hot ashes, wooden shavings
etc.
These items can cause product
failure.
Do not put sharp objects into the
opening of the Roboking 2.0’s
supersonic sensor.
Doing so can cause product failure.
Do not use the Roboking 2.0 when
the dust bin is completely filled up.
Doing so can cause product failure.
When the robot cleaner is
operating, it may hit the chair leg,
desk leg, table leg or other narrow
pieces of furniture.
For quicker and better cleaning,
place the dining chairs on top of the
dining table.
Tip
5
INCLUDED WITH PRODUCT
 Figures can be different from actual objects.
Dust bin filter (spare)
Brush for cleaning filter Mop plate Ultra microfiber mop
(2 pieces) (option)
Dry cell for
remote controller
(2 units of AAA size)
Quick guide
Operation manual
Home station
Roboking 2.0
Remote controller
Side brush
(2 pieces)
OWNER’S MANUAL
CLEANING ROBOT
VR6170LVM
Before using, please carefully read the Safety Precautions pages to
allow for safe operation of the product. After reading the operation
manual, please keep it in an easily accessible location.
www.lg.com
6
PARTS DESCRIPTION - Roboking 2.0
 Figures can be different from actual objects.
Plan view
Manipulation button
Dust bin cover button
Dust bin cover
Status indication lamp
Upper camera sensor
Detecting sensor of home station &
receiving sensor of remote controller
Ultrasonic sensor
Obstacle detecting sensor window
Ventilation port
Cliff detection sensor
Charging terminal
Brush
Side brush
Wheel
Lower camera sensor
Mop plate fixing hook
Battery
Power switch
Front view
Rear view
Bottom view
7
PART DESCRIPTION – HOME STATION / DUST BIN
 Figures can be different from actual objects.
Home station
Dust bin
Remote controller holder
Charging terminal
Reset button
Sponge filter
HEPA filter
Dust bin handle
Dust bin cover
Suction port cover
Dust bin cover
opening button
Power cord fixing hook
8
BUTTON FUNCTIONS – Roboking 2.0
• Use the TIMER button to start cleaning after a set amount of time has elapsed.
• The timer can be set from 1 to maximum of 12 hours in 1 hour units.
• If the timer is set whilst the unit is away from the home station, the cleaning
time will be reduced. Therefore use the product while attached to the home
station as much as possible.
• The timer setting is inoperative if there is no dust bin.
• Press this button to change the cleaning mode.
• When the product is attached to the home station and when the timer is set,
spot cleaning mode cannot be selected.
TIMER
MODE
HOMING
START/STOP
• Press the START/STOP button to turn the Roboking 2.0 on/off or start/stop
cleaning.
• Press the START/STOP button while the Roboking 2.0 is on and it will
automatically start cleaning.
• If the START/STOP button is pressed during automatic cleaning, the Roboking 2.0
will stop cleaning.
• Press and hold the START/STOP button for approximately two seconds to turn
off the Roboking 2.0.
• If the button is pressed while in the timer mode, the reservation will be canceled.
• Press the HOMING button to move the Roboking 2.0 to the home station for
battery charging.
• When cleaning is complete or the battery is low, the device will automatically
move to the home station to charge the battery even without pressing the
HOMING button.
9
BUTTON FUNCTIONS – REMOTE CONTROL
• The Roboking 2.0’s power supply cannot be turned on with the remote control.
• If the main unit is turned off, the remote control will not activate the unit.
• To turn the cleaner on from the stand by mode or off during cleaning, use START/STOP
button on the top of Roboking 2.0.
• In order to do spot cleaning, timer cleaning, zigzag cleaning, and spatial expansion cleaning,
you must first stop the operation of the Roboking 2.0.
Start
The Roboking 2.0 will start
cleaning
Charging
The Roboking 2.0 will move to the
home station for charging.
Timer
The timer can be set from 1-12
hours in the future. (Page 20)
Stop
If the Roboking 2.0 is in operation
it will be stopped.
If it has been set for timer cleaning,
the reservation will be canceled.
Zigzag cleaning
Cleaning will be performed by
the Roboking 2.0 in the zigzag
traveling fashion. (Page 18)
Spot Cleaning
Cleaning will concentrate
within a space of about 1 m
(3.28 ft). (Page 19)
Directional button
The Roboking 2.0 will move
as desired by the user: to
front, rear, left, and right
sides for cleaning.
Cell by Cell cleaning
The Roboking 2.0 will clean
using the spatial expansion
style.
(Page 18)
Tip
10
DISPLAY STATUS INFORMATION
• Once the cleaning mode is selected, it will be kept in memory even when the power is
turned off.
• To cancel the timer setting, press the STOP button on the remote control or the START/
STOP button on the Roboking 2.0.
Zigzag cleaning
• Indicates when the
Roboking 2.0 is in zigzag
cleaning mode. (Page 18)
Timer icon
• This indicates when timer
cleaning has been set up.
(Page 20)
Battery and timer hour
indication
• While waiting for cleaning,
the remaining battery charge
will be shown.
• While waiting for timer
cleaning, the reservation time
will be shown.
• The state of the Roboking 2.0
will be shown. (Page 17)
Spot cleaning
• Indicates when the
Roboking 2.0 is in
spot cleaning mode.
(Page 19)
Spatial expansion
cleaning
• Indicates when the
Roboking 2.0 is in
spatial expansion
cleaning mode.
(Page 18)
Battery icon
• Indicates when the
remaining charge
is displayed on the
battery level indicator,
and flashes when
charging is required.
(Page 17)
Tip
11
BEFORE YOU START
• Do not use this device in a room where a child is left alone. The child could be injured.
• Remove fragile or unnecessary objects from the room to be cleaned.
Especially, remove expensive ceramics and valuables from the floor.
• Close the cover of the dust bin before cleaning.
• Remove any moisture that might be on the floor.
• Remove cables, strips, towels, mat etc. from the floor so they will not get caught by the brush.
• Confirm whether battery charge is sufficient, and if it is low, recharge it.
• Empty the dust bin if it is full.
• Close the doors of any room that you do not want the Roboking 2.0 to enter. During cleaning,
the Roboking 2.0 may enter another room and continue cleaning.
• When the mop is attached, Roboking 2.0 will not be able to go over thresholds of 5mm or higher.
If you are not planning to use the mop for cleaning, separate the mop before using Roboking 2.0.
1. Open the battery cover by lifting the rear hook of the remote controller.
2. Insert two AAA batteries, checking for +, - nodes while loading.
3. Close the battery cover completely so that the batteries will not fall out.
• Only press one button at a time.
• Do not drop or subject it to forceful impact.
• Do not store it near devices that give off heat, fire or hot air.
• Certain fluorescent lamps, such as 3 wavelength fluorescent lamps, can interfere with the activation of the
remote control. Therefore, use it as far away as possible from such lamps.
• If the remote control is far from the Roboking 2.0 when activated, it may fail to operate properly. Use the
device within 3 m (9.84 ft) of the Roboking 2.0 if possible.
Check these items before cleaning
Loading the remote controller battery
Precautions while using the remote control
–
+
+
–
–
+
+
–
–
+
+
–
12
OVERVIEW
1
Install the home station. (Page 13)
Insert the power cord plug into an outlet and locate the
station against a wall. If power is not supplied to the
home station, the Roboking 2.0 will not charge.
2
Turn on the power supply of the Roboking 2.0.
(Page 14)
Turn on the power switch located on the bottom of the
Roboking 2.0 and press the upper START/STOP button
to turn on the power supply.
※
If the power supply is not turned on, refer to page 14.
3
Check the dust bin.
Check the cleanness of the dust bin before starting
the cleaning and close the cover of the dust bin on the
main unit.
4
Start cleaning. (Page 15)
Press the START/STOP button once again while
the Roboking 2.0 is turned on. You will hear the
announcement of cleaning and cleaning will begin.
5
6
Automatic charge. (Page 16-17)
Use the cleaning mode and auxiliary functions.
(Page 18-22)
The Roboking 2.0 will self-diagnose and automatically
return to the home station to recharge before the
complete discharge of the battery. It takes approximately
three hours to charge the battery.
With the Roboking 2.0 and remote controller button, the
cleaning method and auxiliary functions can be used.
Zigzag or spatial expansion (cell by cell) cleaning method
can be selected for the cleaning mode and manual
cleaning, spot cleaning, timer cleaning and micro fiber
mop cleaning can be selected as an auxiliary function.
< Warning > When Roboking 2.0 is operated with the cover of the dust bin open,
it can cause an injury or serious damage to the product.
Flickering
13
HOW TO INSTALL THE HOME STATION
1. Position the home station against a wall, to prevent sliding during
docking, on hard level flooring.
Remove objects within 1m to the right and left side and within
2m to the front.
2. Plug the power cord into an outlet.
Wrap the power cord around the fixed hook on the back side of
the home station or along the wall surface so that the travel path
of the Roboking 2.0 will not be obstructed.
3. Fix the home station against the wall so that it does not move.
4. When the remote controller is not used, store it on the remote
controller holder on the home station.
Fixing hook of power cord
• Always keep the home station plugged in. If the home station is not plugged in, the
Roboking 2.0 will not return to the station to charge automatically.
How to Install the Home Station
< Warning > Do not operate the Roboking 2.0 or its Home Station if it has a damaged cord or plug,
if it is not working properly, or if it has been damaged or dropped. To avoid hazard, the
cord must be replaced by LG Electronics, Inc. or a qualified service person.
Tip
14
HOW TO TURN THE Roboking 2.0 POWER SUPPLY ON & OFF
To turn the power supply on, turn the Roboking 2.0 upside down
on a smooth/soft surface and check whether the main power
supply switch is turned on.
※
Please make sure to remove the dust bin before turning over
the main body. Otherwise, the dust in the dust bin may fall out.
If the main power supply switch is turned off, turn on the switch.
※
When turning on the power switch, do not press the button
located at the upper section of the Roboking 2.0. Operation of
the button can be delayed.
※
Turn off the power switch if the Roboking 2.0 will not be used
for a long period of time, in order to protect the battery.
Press the START/STOP button for two seconds while the
Roboking 2.0 is turned on. A melody will sound when the power is
turned off.
• If the power cannot be turned on, do the following.
- Turn on the power switch if off, and wait for more than 3 seconds.
- Press the ‘START/STOP’ button when the power switch is turned on.
- If the power is not turned on or if there is no display but only the “Ting” sound, put
the Roboking 2.0 on the home station.
- If there is no change even when Roboking 2.0 is attached to the home station, press
the reset switch located on the rear side of the home station for 3 seconds while the
Roboking 2.0 is attached on the home station.
Turning on the main power supply
Turning on from Stand By power.
Turning off the power supply (stand by mode)
Tip
When the Roboking 2.0 is not at the Home Station, and is in the
Stand by mode, press the ‘START/STOP’ button for more than
1 second. The Roboking 2.0 will be turned on and a melody will
be sounded.
※
Roboking 2.0 will automatically return to the home station to
recharge when the charge is low during operation, or if left idle
with no cleaning command for more than 10 minutes.
※
Do not operate Roboking 2.0 on tables or desks. It will result in
an injury or damage to the product when it starts to search for
the home station after 10 minutes.
Be sure to turn the main power off from the on/off switch on
the underside of the unit when placing Roboking 2.0 on high
furniture for storage purposes.
15
HOW TO START AND STOP CLEANING
After the Roboking 2.0 is turned on, press the START/STOP button
to begin cleaning. A melody will sound and cleaning will begin.
Press the START/STOP button during the cleaning cycle to stop
cleaning.
※
When the ‘START/STOP’ button is pressed while the power supply
of the Roboking 2.0 is turned off, the power will be turned on. Press
the ‘START/STOP’ button one more time to start cleaning.
After the Roboking 2.0 is turned on, press the START button on the
remote control. A melody will sound and cleaning will begin.
Press the STOP button during the cleaning cycle to stop cleaning.
※
The Roboking 2.0 cannot be turned on from Stand By, by using the
remote control when the power of the Roboking 2.0 is off. When
the power is off, press the ‘START/STOP’ button on the upper side
of Roboking 2.0 to turn the power on and to allow the remote to be
used.
※
During cleaning, collisions can happen when the sensor cannot detect objects because of their shape (Thin
chair and table leg, furniture corner). When this happens, the internal impact detecting sensor will avoid
the obstacles by using a backward motion.
※
If the Roboking 2.0 is set to start cleaning at a location away from the home station, put the device on
a flat floor in order to prevent a malfunction of the obstacle detecting sensor. In addition, start cleaning
from a location where there are not any obstacles such as curtains or walls within 30 cm (11.8 in) of the
Roboking 2.0.
For best results:
• Briefly scan the area to be cleaned for big and small objects that will cause difficulty for the
Roboking 2.0.
• If cleaning is started when the Roboking 2.0 is at the home station, the device can rapidly be
returned to the home station as the current home position has been accurately read.
• For the safety of the Roboking 2.0, a step height of more than 10mm (0.4 in) cannot be
crossed.
• When then mop plate is fitted, the Roboking 2.0 cannot go over door sills or step treads that
are higher than 5mm.
Using the buttons on the Roboking 2.0
Using the remote control
Tip
16
HOW TO CHARGE THE BATTERY
The Roboking 2.0 returns to the home station at the
end of a cleaning cycle or when its battery is running low.
※
When cleaning is started from the Home-station, Roboking 2.0 will
show better performance in automatic recharge.
(Even in the wide area where the Robot vacuum cleaner cannot see
the signal from Home-station, the Robot will remember the location
if the cleaning is started from the station.
※
In the event that the unit returns to the Home Station due to a low
battery, cleaning will be started, after the charging, from the nearest
place of the area which has not been cleaned before. (Page 17)
※
If Roboking 2.0 is unable to dock to the home station on its first
attempt, it will try again until it docks successfully.
※
When Roboking 2.0 completed all areas that it can clean, it will return to the home station even when the
battery level is not low.
※
Roboking 2.0 will automatically return to the home station to recharge when it's left uncharged or without
cleaning order for more than 10 minutes.
※
Do not operate Roboking 2.0 on tables or desks. It may result in an injury or damage to the product when
it starts to search for home station after 10 minutes.
Be sure to turn the power off when placing Roboking 2.0 on high furniture.
※
If the Roboking commenced cleaning whilst away from the home station, and then the Homing button is
pressed from either the remote or the unit, it may take slightly longer to find the home station.
※
If the Roboking 2.0 stays within 10 cm (3.9 in) of the front of the charging terminal while the power supply
is turned on, it will automatically be returned to the home station and charging will begin.
Automatic charging
Method 1. Attach the Roboking 2.0 to the home station
by aligning to the front side of the home
station. A melody sound will be generated
along with an audio message to start
charging.
※
If an audio message saying “Turn on the
main power switch on the bottom of the
unit” is generated repeatedly when the
Roboking 2.0 is attached to the home
station, please check the power switch
and turn it on.
Method 2. When the HOMING button of the remote
control or the Roboking 2.0 is pressed, the
charge process will start by announcing the
search for the Home Station and will then
attempt to return to it for charging.
Manual charging
Take the following precautions when using the home station:
• If foreign material is covering the charging terminal, charging may not proceed smoothly.
Wipe the terminal from time to time with a dry cloth after the power plug is disconnected.
• To prevent electric shock, do not touch the charging terminal with any metallic objects.
• To avoid fire or electric shock, never disassemble or modify the home station.
• Do not to place the home station or power plug near to a heating appliance.
Tip
If using the Roboking 2.0 for the first time or when charging the battery during cleaning, you can manually
charge the battery.
17
HOW TO CHARGE THE BATTERY
Check 1:
If the battery is not charging even when the Roboking 2.0 is
attached to the home station, check the following items.
- Turn the power switch on the bottom of the Roboking 2.0
off once and then on again.
- Check the power lamp of the home station.
- Wipe the terminal on the home station with a dry cloth
Check 2:
If the battery is still not charging after the previous check,
try the following.
- Manually attach the Roboking 2.0 to the home station.
- Press the reset button at the rear of the home station for
three seconds.
The remaining battery charge can be confirmed from the charge indication light, which will indicate charge
as follows:
• During charging, the charge remaining indication light will icker.
• When charging is completed at the home station, only the battery icon will illuminate to save power.
• The battery icon will icker when battery charging is required.
Full charging
(Under charging)
The status indication lamp
while the robot is charged
(In spatial expand mode)
High Middle Low Charging is
required
※
If there is still an area to be cleaned when the Roboking 2.0
is returned to the home station for charging, the selected
cleaning mode is displayed.
- When the battery is fully charged, it cleans the area that
remains to be cleaned. (Perform 1 time)
- During charging, when the cleaning mode is displayed,
pressing the START button on the remote controller or
the START/STOP button on Roboking 2.0 will cause the
Roboking 2.0 to search for the un-cleaned area and start
cleaning.
- Pressing the mode selection button (ZIGZAG, CELL BY
CELL) will start the cleaning process from the beginning.
Remaining Battery Charge Indicator
If the Battery is Not Charging
Flickering
In the case of not
existing an area to
be cleaned
In the case of
existing an area
to be cleaned
(Flickering)
Charge
terminal
18
CLEANING MODES
With zigzag cleaning, the total of the cleaning area will be
cleaned with the repetition of zigzag traveling.
If rapid cleaning is desired, use zigzag cleaning.
When pressing ‘ZIGZAG’ button on the remote controller,
zigzag cleaning will be started while zigzag cleaning icon is
indicated by the indication lamp.
With spatial expansion cleaning, the cleaning will be
performed by dividing the cleaning area into partial square
spaces.
If elaborate cleaning is desired, use spatial expansion
cleaning.
When pressing ‘Cell by Cell’ button on the remote
controller, spatial expansion cleaning will be started
while spatial expansion cleaning icon is indicated by the
indication lamp.
The 1st stage:
The maximum outline of 3m x 3m of cleaning area
will be cleaned. (The size of outline will be changed in
accordance with the shape of the house inside.)
The 2nd stage:
Inside of the outline will be cleaned with zigzag traveling.
When the 1st, 2nd stages are completed, the inside of
the cleaning area will be cleaned through the repetition of
above cleaning method as the device is being moved to
the next cleaning area.
• Once set up, the cleaning mode will be kept in memory even after the power supply is
turned off.
• During operation, if a mode change is required, press the STOP button and then select the
mode.
Zigzag Cleaning
Spatial Expansion Cleaning
Tip
19
AUXILIARY CLEANING MODES
This method of cleaning involves manually moving the Roboking 2.0 by pressing the directional (arrow)
buttons on the remote control.
The interior space will be cleaned by the Roboking 2.0 as it is being moved to the front, rear, or rotated to
the left and right side according to the input of the directional buttons.
If it meets an obstacle during manual cleaning in a forward motion, it stops.
Use this cleaning method when concentrated cleaning of a small interior space is required.
After moving the Roboking 2.0 to the location to be cleaned, press the SPOT button on the remote control.
The spot cleaning icon will illuminate on the Roboking 2.0, and concentrated cleaning will be performed for
a space within a radius of 1 m (3.28 ft).
※
During charging, the spot cleaning button on the remote control will not activate.
※
The following device show weaker on inhalation
than ordinary vacuum cleaner, but with rotation
brush and side rotation brushes, the device
shows similar performance on cleaning as
ordinary vacuum cleaner.
Manual cleaning
Spot Cleaning
It stops at the started position after
completing the cleaning(takes 4~5 min.).
Brush
Side brush
20
TIMER CLEANING
1. By pressing the TIMER button on the remote
control or the Roboking 2.0, a cleaning time can be
scheduled.
2. Adjust the time as much as desired by multiple
presses of the TIMER button. Each time you
press the button, the time will increase by one
hour.
- The start time can be set up to a maximum of
12 hours and once set up, the time in hours, will
be indicated by the status indication lamps.
3. After setting up the start time, press the START/STOP
button on the Roboking 2.0 or wait about five seconds.
When the timer setting is complete, a melody will sound,
and the timer indicator will remain on.
- If the timer is set, timer icon of a clock shape is
displayed on the status indicator lamp.
Set the timer to schedule the cleaning and begin in 1-12 hours.
The timer setting is inactive if there is no dust bin.
• When the set up time elapses, cleaning will start automatically.
• Use the timer setting when the Roboking 2.0 is attached to the home station. If the timer is
set while Roboking 2.0 is away from the home station, the cleaning time can be shortened.
• To cancel the timer setting during the set up time, press the STOP button on the remote
control or the START/STOP button twice on the Roboking 2.0.
1 hour
9 hours
6 hours
12 hours
Tip
21
MOP CLEANING (OPTION)
1. Attach the ultra microfiber mop to the Velcro
of the mop plate as shown in the figure.
※
To prevent the Roboking 2.0 from
malfunctioning, attach the mop so that the
mop attaching guide will not be covered by
the mop.
2. Accurately match up and insert the mop plate
fixing hook on the lower section of the
Roboking 2.0 into the fixing groove of the
mop plate.
3. When you accurately match up and press the
mop plate to the rear side of the Roboking 2.0,
it will mount with a clicking sound.
※
Be careful to properly mount the mop plate,
or it can separate during cleaning.
For mop cleaning, mount the mop and mop plate to the Roboking 2.0 according to the following instructions:
By attaching the ultra microfiber mop, you can
effectively use the Roboking 2.0 to remove dust
from hard floors.
When the mop plate is attached, the Roboking 2.0
will not climb on to carpets or over thresholds, in
order to prevent transferring dirt from the mop.
• To avoid odors, wash any foreign material or dust off the mop after cleaning is complete.
• To avoid staining floors, do not use the ultra microfiber mop to clean when dirt is mixed with
liquids such as coffee or ink.
• To avoid damage to carpets from the Velcro or dirt transfer from the mop, do not clean the
carpet while the mop plate or mop is attached.
• Keep the ultra microfiber mop dry. Do not use it on wet surfaces.
If there is moisture, it can interfere with the navigation.
Ultra microfiber mop
Mop plate
Mop plate
Fixing hook
Fixing groove
“Click!”
Ultra microfiber mop
Ultra microfiber mopUltra microfiber mop
Mop fixing section With mop attached
Bottom camera sensor
Tip
22
LOCATION SEARCH FUNCTION
When the user removes any abnormal condition of
Roboking 2.0 or moves the location arbitrarily, the
location search function will activate.
1. Locate Roboking 2.0 near the location where
Roboking 2.0 was moved.
※
Location search is more effective when
Roboking 2.0 is closer to the location where it
was moved.
※
If it goes out of diameter of 1m from the
occurrence position, it becomes difficult to
search the position.
2. Press the START/STOP button on Roboking 2.0 or START button on the remote controller.
Roboking 2.0 will start the location search function along with an audio guide.
※
When the location search is successfully completed, Roboking 2.0 will continue to the cleaning from where
it was moved. If position search fails, it will start again from the beginning.
Roboking 2.0 remembers its location while cleaning.
If the user moves the Roboking 2.0 while it is operating, it will search its location with
the location search function so that it can continue from the previous location.
Change location
Location of incident
Location of incident
1m
1m
When the location search
function is activated, the
cleaning mode of the status
indicator will flash
Checking current location.
• When the power is turned off after the location search function is set, the location search
function will be canceled.
• Location search is more effective when Roboking 2.0 is closer to the location where it was
moved.
• The position search function will be cancelled if the remote is pressed to engage any other
function.
Tip
23
CLEANING THE DUST BIN
1. Open the dust bin cover by pressing the PUSH
button on the Roboking 2.0.
2. Grab the handle of the dust bin and pull it
upward.
3. Separate the HEPA filter and the inside sponge
filter by removing the HEPA filter
※
To clean the dust bin filter, refer to page 24.
4. Lift the cover upward while pressing the
separation button on the dust bin.
5. Empty the dust bin and clean it with a cleaning
brush or under running water.
※
Please use vacuum cleaner when cleaning the
filter.
(Be sure to fully dry the filter after washing it. It
may can affect inhalation or can make smell.)
6. After cleaning with water, completely dry the dust
bin in a well-ventilated area out of direct sunlight.
7. When you have completed cleaning the dust bin,
close the dust bin lid and replace the sponge
filter and HEPA filter.
8. Put the dust bin into the Roboking 2.0 and close
the dust bin cover.
If the dust bin is full, suction power can be weakened. Clean the dust bin before and after each cleaning
session. Clean the dust bin using the following sequence:
• After cleaning, always mount the dust bin filters (HEPA filter, sponge filter) to the dust bin.
If they are not mounted, dust may enter the Roboking 2.0 interior and cause product failure.
• After cleaning the dust bin, make sure to start the operation with the dust bin installed.
If operation is attempted without the dust bin, a voice message, “please check the dust bin”
will sound.
Tip
24
CLEANING THE DUST BIN FILTER
The dust bin filters are comprised of the HEPA filter and the sponge filter.
Clean the HEPA filter and the sponge filter according to the following sequence:
1. Separate the HEPA filter and the inside sponge
filter by removing the HEPA filter (as shown).
3. After washing the HEPA filter and the sponge filter
with water, place them out of direct sunlight and allow
them to dry completely.
※
Please use vacuum cleaner when cleaning the filter.
(Be sure to fully dry the filter after washing it. It may
can affect inhalation or can make smell.)
4. Mount the cleaned HEPA filter and sponge filter
into the dust bin according to the sequence
shown to the right. When assembling the filter,
the filter handle should face upward.
2. Carefully clean any fine dust off the HEPA filter and
the sponge filter with a vacuum cleaner or water.
• In order to maintain the performance of the Roboking 2.0, the HEPA filter should be cleaned
with a cleaning brush or vacuum cleaner at least once a week, and should be washed under
running water at least once a month.
Tip
25
CLEANING THE BRUSH
Insert the fixing hook on the
opposite side of the brush
(marked with a rounded
rectangle) by matching it to
the separation groove of the
brush.
Insert the fixing guide in front
of the brush by matching it to
the fixing groove located on the
main unit.
Close the cover by pressing
it down until you hear a click
from the fixing hook.
※
Be careful that the side
brush is not caught by the
cover.
Grab the brush and remove
by pulling it up.
Clean the brush with a vacuum
cleaner, scissors, etc.
Insert the fixing hook on the
side of the brush (marked with
the square) by matching it to
the fixing groove of the brush.
Lay a smooth cloth on the
floor. Turn the Roboking 2.0
over and put the Roboking
2.0 on the cloth. Turn off the
power switch before cleaning.
Separate the cover by pressing
the fixing hook and pulling
upward.
Wearing gloves turn the brush
until the separation groove of
the brush appears.
The brush, located on the bottom of the Roboking 2.0, helps with the suction of foreign objects. Perform
the following steps to clean the brush:
※
Please make sure to remove the dust bin before turning over the main body.
Otherwise, the dust in the dust bin may fall out.
Separation
groove of
brush
26
CLEANING THE SENSOR/CHARGING TERMINAL
Receiving sensor of
remote controller
Camera sensor
• Do not clean the Roboking 2.0 by directly spraying it with water, thinner, benzene, etc.
• Call the service center if the sensor or charging terminal is damaged. Sensor and terminal
damage can cause the product to malfunction.
There are sensors on the Roboking 2.0 that can detect obstacles, stairways
and the home station for charging the battery. In order to maintain the
performance of the Roboking 2.0, regularly clean the sensors and charging
terminal as follows:
1. Lay a smooth cloth on the floor, overturn the Roboking 2.0 and put it on
the cloth.
※
Please make sure to remove the dust bin before turning over the main body.
Otherwise, the dust in the dust bin may fall out.
2. Turn off the power switch on the bottom of the Roboking 2.0. Injury can
be caused by the activation of the Roboking 2.0 if the main power is not
turned off.
3. Use a smooth cloth or cleaning brush to wipe the dust off each sensor
and the charging terminal as described below.
Charging terminal
Obstacle detection sensor
Cliff detection sensor
Charging terminal
Bottom camera sensor
Lens
Tip
※
The device may move backwards while operating when the cliff sensor or bottom camera sensor is
contaminated.
Please clean the sensor with soft brush or cleaning brush.
27
CLEANING THE SIDE BRUSH
Foreign objects/materials such as hair can easily adhere to the side
brush. Remove such materials at least once a week.
If excessive amounts of foreign materials are stuck to the brush,
there is the risk of damage to the brushes.
If the floor is rough or skirting boards are frequently cleaned, the side brush may bend or become
damaged. In this case, use the following method to straighten the side brush.
1. The following procedure is helpful in restoring
deformed brushes.
2. Turn off the power supply by pressing the
START/STOP button on the Roboking 2.0 for two
seconds.
3. Place the Roboking 2.0 at the end of a table to
make cleaning the side brush easier. Make sure
that the Roboking 2.0 is not in danger of falling.
4. Soak the side brush in warm water.
5. Press down on the side brush for about ten
seconds so that it is completely submerged in
the water.
6. Slowly wipe the side brush by sliding it through
your hand.
7. Rotate the side brush and repeat steps 4-6 for
each section of the brush.
8. Use the side brush only after it has completely
dried.
1. Remove the screw and separate the side brush.
2. Exchange and re-assemble new side brushes.
How to change the side brush
28
CLEANING THE ULTRA MICROFIBER MOP (OPTION)
1. Separate the ultra microfiber mop from the mop plate.
2. Carefully clean it with water.
3. Use the mop only after allowing it to dry completely in a
sunny, well-ventilated area.
To avoid odors, dirt and dust should be washed off the mop after it is used for cleaning. Follow these
directions to wash the ultra microfiber mop:
• To avoid product malfunction, only use the ultra microfiber mop provided with
the Roboking 2.0.
• Additional microfiber mops can be purchased by visiting a nearby LG Electronics service
center.
Tip
29
TROUBLESHOOTING
If the unit becomes stuck or suspended and the wheels do not allow the unit to move, the voice,
“Please check the wheels”, will be announced.
• Is a wheel trapped in a oor gap, door, balcony, stairway, etc?
 Move the Roboking 2.0 on to the flat floor.
• Is any foreign material wound around the wheel?
Lay a protective cloth on the floor, overturn the Roboking 2.0, and put it on the cloth.
Remove foreign material by confirming the wheel.
※
Please make sure to remove the dust bin before turning over the main body.
Otherwise, the dust in the dust bin may fall out.
• Is the Roboking 2.0 stuck?
After removing the part that is stuck, place the Roboking 2.0 on flat floor.
When the voice, “Please check the wheels”, is announced.
30
TROUBLESHOOTING
When an abnormality is detected with the dust bin, the voice,
“Please check the dust bin”, is announced.
• Is the dust bin tted correctly?
Open the dust bin cover, and if check if the dust bin is actually fitted.
The unit will not operate without the dust bin.
 If the dust bin cover is opened, close the cover before operating the unit.
When remaining amount of battery is almost nil, the voice, “Battery is low”, is generated.
• Initiate battery charging of Roboking 2.0 by moving it to the home station.
If Roboking 2.0 is attached to the docking station, it will start the recharging with the recharging start
melody.
When the voice, “Please check the dust bin”, is announced
When the voice, “Battery is low”, is announced.
31
TROUBLESHOOTING
Proper assembly assures that the rotation of
the brush becomes smooth.
※
For a more detailed description of this process, refer to the instructions on page 25.
When the Roboking 2.0 detects that the brush is not functioning properly, you will hear the message
“Please check the brush.”
Lay a protection cloth on the floor, overturn the Roboking 2.0, and place it on the cloth.
※
Please make sure to remove the dust bin before turning over the main body.
Otherwise, the dust in the dust bin may fall out.
• The side brush is stuck.
Remove any foreign materials such as cables, thread or hair caught in the side brush or the brush.
 Confirm the correct assembly of the brush by checking the separation groove of the brush.
• The brush is making a loud, abnormal sound.
Remove the brush from the Roboking 2.0 and remove any foreign material from the brush.
When the voice, “Please check the brush”, is announced
Separation
groove of brush
Separation
groove of brush
32
BEFORE YOU CALL FOR SERVICE
Confirm before reporting the failure of Roboking 2.0.
Problem Solutions (Reference page)
The Roboking 2.0 will not
activate.
Confirm that the power switch is turned on. (Page 14) Ƭ
Confirm that the battery has been charged. (Page 17) Ƭ
Movements or travel path are
abnormal.
Carefully wipe the sensor with a smooth cloth. (Page 26) Ƭ
If the ultra microfiber mop is attached, confirm that it is mounted Ƭ
properly. (Page 21)
Turn on the power switch off and on. Ƭ
Suction power becomes weak. Check whether there is foreign material blocking the suction port. Ƭ
(Page 25)
Empty the dust bin. (Page 23) Ƭ
Clean the dust bin filter. (Page 24) Ƭ
Noise becomes louder. Confirm that the dust bin has been mounted properly. Ƭ
Confirm that the dust bin filter has been mounted properly. Ƭ
(Page 24)
Check whether foreign material is caught in the brush. (Page 25) Ƭ
Please check if there is any tape, gum or other kind of foreign Ƭ
materials are on the wheel.
The Roboking 2.0 cannot
be activated with the remote
control.
Replace the remote control batteries. (Page 11) Ƭ
Confirm that the control is within the coverage area of the main unit, Ƭ
which is less than 3 m or 9.84 ft. (Page 11)
Check whether the main power switch on the bottom is turned on. Ƭ
(Page 14)
The brush does not rotate. Clean the brush. (Page 25) Ƭ
Confirm that the brush has been mounted properly. (Page 25) Ƭ
The Roboking 2.0 will not
charge.
Remove objects around the home station. (Page 13) Ƭ
Confirm that the power supply is connected to the home station. Ƭ
(Page 13)
Wipe the charging terminal with a dry cloth. Ƭ
Press the reset button on the back of the home station for Ƭ
3 seconds while the Roboking 2.0 is attached to the home station.
(Page 14)
Automatically starts
searching for home station.
Automatically turns
the power off.
Roboking 2.0 will automatically return to the home station to recharge
when it's left uncharged or without cleaning order for more than 10
minutes.
The power supply cannot be
turned on.
Check that the power switch is turned on. (Page 14)
33
PRODUCT SPECIFICATIONS
Item/Model LG Roboking 2.0
VR6170LVM
External Dimensions
Φ
360 mm
×
90 mm
Weight 3.2 kg
Power Consumption 18 W
Battery (Fully Charging) DC 16.8 V
Traveling Velocity 350 mm/sec
Use Time Approx. 100 minutes
(Based on general wooden floor)
Charging Time 3 hours
Main Functions Obstacle detection
Fall prevention
Timer cleaning
Error indication
Location search
Automatic / manual charging
Dry mop (Wiping)
Corner cleaning
Voice output
Map building
Spot cleaning
Spatial expansion cleaning
Zigzag cleaning
Item/Model Home Station VR607
External Dimensions 245 mm
×
193 mm
×
132 mm
Rating AC 220-240V,50Hz
Output Voltage/Current 17.1VDC / 1.1 A
Power Consumption 23 W
Item/Model Battery
Type Lithium Ion Polymer Battery
34
REFERENCE ITEMS
Open source software notice
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available
for download.
Disposal of waste batteries/accumulators
1. When this crossed-out wheeled bin symbol is attached to batteries/accumulators of Your product it means they
are covered by European Directive 2006/06/EC.
2. This symbol may be combined with chemical symbols for mercury(Hg), cadmium(Cd) or lead(Pb) if the battery
Contains more that 0.0005% of mercury, 0.002% of cadmium or 0.004% of lead.
3. All batteries/accumulators should be disposed separately from the municipal waste stream via designated
collection facilities appointed by the government or the local authorities.
4. The correct disposal of Your old batteries/accumulators will help to prevent potential negative consequences for
the environment, animal and human health.
5. For more detailed information about disposal of Your old batteries/accumulators, please contact Your city office,
waste disposal service or the shop where You purchased the product.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the
European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the municipal waste stream via
designated collection facilities appointed by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment
and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office, waste
disposal service or the shop where you purchased the product.
WARNING
Please be careful of fire, explosion, electric shock, or breakdown.
• Do not charge this Battery Pack(Pack hereafter) with any other type of charger than the one originally
provided whit the charger.
• Do not damage the Pack in such ways as drop, crush, puncture, cut or short extemal contacts.
• Do not attempt to disassembly the pack In any case. When the Pack is damaged or malfunctioning,
bring it to the service center.
• Do not place this pack near a heat source or do not dispose of in fire or water.
• Please keep the Pack away from damp or wet environment when the pack is charged.
• Please keep away from children, infant or pets.
MEMO
MEMO
Made in Korea
… 24 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw LG VR6170LVM bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van LG VR6170LVM in de taal/talen: Engels als bijlage per email.

De handleiding is 23,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van LG VR6170LVM

LG VR6170LVM Gebruiksaanwijzing - Deutsch - 40 pagina's

LG VR6170LVM Gebruiksaanwijzing - Deutsch, English, Français, Italiano - 39 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info