598283
49
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
Do not remove this Owner’s Manual from the vehicle. Read this manual carefully
before operating the vehicle as it contains important safety information.
Read this manual carefully.
This Owner’s Manual contains important information on safety, operation and maintenance of your KYMCO scooter.
Any one who operates your scooter should carefully read and understand the contents of this manual before riding the scooter.
For your safety, understand and follow all of the warnings contained in this Owner’s Manual and the labels applied to your scooter.
This Owners Manual should be considered a permanent part of the vehicle, keep it with your scooter at all times.
ON-ROAD USE ONLY This scooter has been designed to be used on the road.
Particularly important information is called out in this manual by the following icons and notations:
WARNING
CAUTION
NO NO
NO NO
NO
TETE
TETE
TE
The SAFETY ALERT symbol with the exclamation point in the triangle means ATTENTION!
BE ALERT! YOUR SAFETY CAN BE AFFECTED.
Failure to follow instructions associated with a WARNING symbol could result in severe injury or
death to the rider, a passenger, a bystander, or a person inspecting or repairing the scooter.
A CAUTION symbol indicates that special precautions must be taken to avoid damaging
the scooter.
The NOTE symbol indicates key information about a procedure or to clarify an operation.
California Proposition 65
WARNING
This product contains or emits chemicals known to the State of California to cause
cancer and birth defects or other reproductive harm.
1
Manual Icon Legend ....................................................(inside of front-cover)
CA Prop 65 Warning ....................................................(inside of front-cover)
Table of Contents.......................................................................................... 1
SECTION 1 - SAFETY .................................................................2 - 6
Foreword ....................................................................................................... 2
Scooter Safety ......................................................................................... 3 - 4
Load Limits & Guidelines ............................................................................. 5
Accessories & Modifications ........................................................................ 6
SECTION 2 - CONTROLS & FEATURES............................... 7 - 15
Locations of Parts & Controls .................................................................7 - 8
Keys............................................................................................................... 9
Ignition Switch & Steering Lock ............................................................9 - 10
Right-hand Handlebar Switch .................................................................... 11
Engine-stop Switch ..................................................................................... 11
Electric Start Button.................................................................................... 11
Left-hand Handlebar Switch................................................................ 11 - 12
Headlight Dimmer Switch ........................................................................... 11
Turn Signal Switch ...................................................................................... 12
Turn Signals ................................................................................................ 12
Under-seat Storage Compartment ............................................................ 12
Helmet Posts............................................................................................... 13
Main Stand .................................................................................................. 13
Instruments ................................................................................................. 14
Clock............................................................................................................ 14
Passenger Foot Rest.................................................................................. 15
SECTION 3 - OPERATION..................................................... 16 - 32
Break-in Recommendations....................................................................... 16
Tire Break-in................................................................................................ 17
Pre-ride Inspection ...............................................................................18 -25
Engine Oil Inspection ................................................................................. 19
Brake Inspection ..................................................................................19 - 20
Tire Inspection .....................................................................................20 - 21
Fuel Level / Filler Cap ................................................................................ 22
TABLE OF CONTENTS
Steering & Handlebar Inspection ............................................................... 23
Instrument Inspection ................................................................................. 23
Horn & Lights Inspection ............................................................................ 24
Chassis Inspection ..................................................................................... 25
Starting the Engine (electric start) ......................................................26 - 27
Starting the Engine (kick start)................................................................... 27
Riding Your Scooter .............................................................................28 - 31
Parking Your Scooter ...........................................................................31 - 32
SECTION 4 - MAINTENANCE ............................................... 33 - 50
Importance of Maintenance ....................................................................... 33
Maintenance Schedule ........................................................................34 - 35
Tires............................................................................................................. 36
Tire Pressure............................................................................................... 36
Air Filter Maintenance ................................................................................ 37
Fuel System ................................................................................................ 38
Battery ..................................................................................................38 - 39
Fuse............................................................................................................. 39
Engine Oil.................................................................................................... 40
Engine Oil Level Inspection & Change...............................................40 - 41
Transmission Fluid Change ....................................................................... 42
Spark Plug................................................................................................... 43
Brake Fluid Level Inspection ...................................................................... 43
Brake Shoe & Pad Inspection .................................................................... 44
Cleaning Your Scooter.........................................................................45 - 46
Storage .................................................................................................47 - 48
Maintenance Record ...........................................................................49 - 50
Specifications (Agility 50) ........................................................................... 51
Specifications (Agility 125) ......................................................................... 52
Emission - KYMCO Clean Air System ....................................................... 53
Emission Information & EPA Warranty ...................................................... 54
KYMCO Limited Scooter Warranty ............................................................ 55
Index ............................................................................................................ 56
Identification Numbers Record .................................. (inside of back-cover)
2
Thank you for purchasing this KYMCO Agility scooter, and welcome to the KYMCO riding family.
Please read this owner's manual carefully before riding so that you will be thoroughly familiar with the
proper operation of your scooter’s controls, its features, its capabilities, and its limitations.
To ensure a long, trouble-free life for your scooter, provide it with the proper care and maintenance as
described in this manual.
For replacement parts and accessories, you should always use genuine KYMCO products, as they have
been specially designed for your vehicle and manufactured to meet KYMCO's demanding standards.
Keep this owner's manual aboard your scooter at all times, so that you can refer to it whenever you need
information. This manual should be considered a permanent part of the scooter and should remain with the
scooter when it is sold.
All information, illustrations, photographs and specifications contained in this manual are based on the
latest product information available at the time of publication. Due to improvements or other changes, there
may be information in this manual that differs slightly from your vehicle. KYMCO reserves the right to make
product and publication changes at any time, without notice, and without incurring any obligation.
SECTION 1 -
FOREWORD & SAFETY INTRODUCTION
3
IMPORTANT SAFETY INFORMATION
Your scooter can provide you many years of service and plea-
sure if you take responsibility for your own safety and under-
stand the challenges that you can meet on the road. There is
much that you can do to protect yourself when you ride. You
will find many helpful recommendations throughout this
manual. Here are some very important safety tips:
Wear a helmet
Scooter safety equipment starts with a quality helmet. One of
the most serious injuries you can suffer in a crash is a head
injury. Always wear a properly approved helmet. You should
also wear suitable eye protection.
Make yourself easy to see
To make yourself more visible, wear bright, reflective clothing;
position yourself so other drivers can see you; signal before
turning or changing lanes; and use your horn when it will help
others notice you.
Know your limits
Ride within the boundaries of your own skill at all times. Know-
ing these limits and staying within them will help you avoid
accidents.
SCOOTER SAFETY
Keep your scooter in safe condition
For safe riding, it's important to inspect your scooter before
every ride and perform all recommended maintenance. Never
exceed load limits, and only use accessories that have been
approved by KYMCO for this scooter.
Inspect your scooter before riding
Do not forget to perform an entire safety inspection to ensure
your, and your passenger's safety, before each ride.
Be extra safety conscious on bad weather days
Riding on bad weather days, especially wet ones, requires ex-
tra caution. Braking distance can double on a rainy day. Stay
off of painted surfaces, manhole covers and greasy appearing
areas on the pavement, as they can be especially slippery. Use
extreme caution at railway crossings and on metal gratings and
bridges. Whenever your are in doubt about the road conditions,
slow down.
Modification
Modification of your scooter, or removal of original equipment
may render the vehicle unsafe or illegal. Obey all applicable
equipment regulations in your area.
4
SCOOTER SAFETY
PROTECTIVE APPAREL
For your safety, always wear an approved motorcycle or scooter
helmet, eye protection, boots, gloves, long pants, and a long-
sleeved shirt or jacket whenever you ride your scooter.
Helmets and protection
Your helmet is your most important piece of riding gear be-
cause it offers the best protection against head injuries. Your
helmet should fit your head comfortably and securely. Always
wear a face shield or goggles to protect your eyes and to aid
your vision.
Additional riding gear
In addition to a helmet and eye protection, you should also use:
Sturdy boots with nonslip soles to help protect your
feet and ankles
Leather gloves to keep your hands warm and help pre-
vent blisters, cuts, burns and bruises
A motorcycle or scooter riding suit or jacket that has
been designed for comfort as well as protection. Bright
colored and reflective clothing can help make you more
noticeable in traffic. Be sure to avoid loose clothing
that can get caught on any part of your scooter.
1 Wear bright or reflective clothing. Clothes should fit
properly (not too tight or loose)
2 Always wear a helmet and eye protection
3 Wear gloves
4 Footwear should be the proper size, have low heels,
and offer ankle protection
Not wearing a helmet increases your chance of serious
injury or death in a crash.
Be sure you and your passenger always wear an approved
motorcycle helmet that fits properly. You should also wear
eye protection and other protective apparel when you ride.
11
11
1
22
22
2
33
33
3
44
44
4
5
LOAD LIMITS & LOADING GUIDELINES
These general guidelines may help you decide how to add
accessories to your scooter and how to load it properly.
Load limits
These specifications are the load limits for your Agility scooter.
Overloading the scooter will affect its stability and handling.
Be sure to stay within the limits given below:
Maximum weight capacity (Includes the weight of the rider,
passenger, cargo and accessories):
Agility 50..................................................... 544 lbs (247 kg)
Agility 125................................................... 570 lbs (259 kg)
Maximum cargo weight:................................. 22 lb (10 kg)
Under-seat compartment
55
55
5 weight limit: ......11 lbs (5 kg)
Rear carrier (rack)
6 6
6 6
6 weight limit:...................11 lbs (5 kg)
Loading guidelines
Improperly loading your scooter will affect its stability and han-
dling. You should ride at reduced speeds when you are carrying a
passenger or cargo. Follow these guidelines whenever you carry
a passenger or cargo:
Check that both tires are properly inflated
To prevent loose items from creating a hazard, make
sure all cargo is securely tied down before you ride
Place cargo weight as close to the center of the scooter
as possible
Balance cargo weight evenly on both sides of the scooter
Overloading or improper loading will affect vehicle han-
dling, stability and braking, and can lead to an accident.
Never exceed the stated load capacity of your scooter.
Cargo should be properly distributed and securely at-
tached. Reduce speed when carrying cargo. Allow greater
distance for braking.
55
55
5
66
66
6
6
ACCESSORIES & MODIFICATION
There is a large variety of accessories available to KYMCO
scooter owners. KYMCO cannot have direct control over the
quality or suitability of accessories you may wish to purchase.
The addition of unsuitable accessories to your scooter can
lead to unsafe operating conditions. It is not possible for
KYMCO to test each accessory on the market, or all of the
combinations of the available accessories; however, your
KYMCO dealer can assist you in selecting quality accessories
and then install them correctly.
Use extreme caution when selecting and installing the ac-
cessories for your scooter.
No modifications
KYMCO strongly advises you against removing any original
equipment or modifying your scooter in any way that would
change its design or operation.
Improper accessories or modifications can make your
scooter unsafe and can lead to an accident.
Never modify your scooter through the improper installa-
tion or use of accessories. All parts and accessories added
to this vehicle should be genuine KYMCO or equivalent
components designed for use on this scooter and should
be installed and used according to instruction. If you have
any questions, consult an authorized KYMCO dealer.
7
1 Left front turn signal
2 Rear brake lever
3 Turn signal switch, headlight dim-
mer switch, passing light button,
horn button
4 Under-seat storage compartment
5 Fuel filler
6 Tail/Brake Light
7 Left rear turn signal
8 Kick start lever
9 ESN (Engine Serial Number)
AT Main stand
NOTE: Your scooter may differ slightly in appearance from the images in this manual.
NOTE: Write your scooters VIN and ESN in the boxes provided in the inside, rear cover of this Owner's Manual.
SECTION 2 -
CONTROLS & FEATURES
Location of parts & controls
22
22
2
11
11
1
33
33
3
44
44
4
55
55
5
66
66
6
77
77
7
88
88
8
99
99
9
ATAT
ATAT
AT
8
CONTROLS & FEATURES
Location of parts & controls
NOTE: Your scooter may differ slightly in appearance from the images in this manual.
NOTE: Write your scooters VIN and ESN in the boxes provided in the inside, rear cover of this Owner's Manual.
1 Battery
2 Exhaust muffler
3 Right rear turn signal
4 Rear carrier
5 Ignition switch
6 Engine stop switch, starter motor
button
7 Instruments (Speedometer)
8 Center console
9 Right, front turn signal
AT VIN (Vehicle Identification Number)
33
33
3
44
44
4
55
55
5
66
66
6
77
77
7
88
88
8
99
99
9
ATAT
ATAT
AT
22
22
2
11
11
1
9
Keys
Your Agility scooter is supplied with two identical ignition switch
keys. The ignition key operates the ignition switch, the steer-
ing lock, and is used to open the seat to gain access to the
center compartment and the fuel filler cap.
The keys have a unique code that is stamped on the tab sup-
plied with the keys. This code is not stamped on the scooter
and is not recorded in the vehicle's basic documentation for
security reasons. Since this code is required if you need re-
placement keys, record this important code in the box provided
on the inside, rear cover of this Owner's Manual.
Ignition switch & Steering lock
CONTROLS & FEATURES
NOTE: Your scooters keys may differ slightly in appearance from
the images in this manual.
1 1
1 1
1 ON: In this position, electrical power is connected to start
and operate the engine (the key cannot be removed).
2 2
2 2
2 OFF: In this position, electrical power is disconnected and
the engine cannot start or operate (the key can be removed).
22
22
2
Key code tab
11
11
1
10
CONTROLS & FEATURES
After locking the ignition switch, turn the handlebar gen-
tly to confirm that the steering is locked. Do not park
your scooter in a position that will interfere with vehicle
or pedestrian traffic.
Do not turn the ignition switch to the lock position when
riding, as this could cause the steering to lock and you
could lose control of your scooter.
33
33
3
3 3
3 3
3 LOCK: In this position, the steering is locked, electrical
power is disconnected and the engine cannot start or oper-
ate (the key can be removed).
Locking the steering
Turn the handlebar fully to the left. Press in and rotate the
ignition switch key counterclockwise to the “LOCK” position.
The steering will now be locked. Remove the ignition switch
key.
Unlocking the steering
Insert and rotate the ignition switch key clockwise from the
“LOCK” position to the “OFF” or “ON” position. The steering is
now unlocked, and you may start and operate the scooter.
11
Right handlebar switch
NOTE: The starter motor will not engage unless a brake le-
ver is squeezed at the same time the starter button is pressed.
Electric starter button
22
22
2:
Press the electric starter button to activate the starter motor.
Engine stop switch
11
11
1:
The engine stop switch turns off the ignition, stopping the en-
gine, but the scooter’s lights and horn will still function.
To prevent damage to the starter motor, do not operate
the starter motor for more than five seconds at a time. If
the scooter fails to start immediately, check the fuel level
and the battery condition, and allow the starter motor to
cool before attempting to start the engine again.
CONTROLS & FEATURES
Left handlebar switch
Headlamp switch -- UP
33
33
3:
The upper switch position turns the headlight high beam on.
The high beam indicator light on the dash is activated as well.
Headlamp switch -- DOWN
44
44
4:
The lower switch position turns the headlight low beam on.
Passing light button - PRESS DOWN
55
55
5:
When downward pressure is applied to the headlight rocker
switch, the high beam is activted. When pressure is released,
the the low beam setting is restored. This enables you to rapidly
flick the headlight high beam on and off to signal other vehicles
that you wish to pass.
11
11
1
22
22
2
33
33
3
44
44
4
55
55
5
12
Under-seat storage compartment
Your scooter is equipped with an under-seat storage compart-
ment that permits you to secure your helmet or other items.
To open the seat, insert the ignition switch key into the seat lock
AT and turn it clockwise. When the latch releases, lift up the seat.
Under-seat compartment weight Iimit: .........11 lbs (5 kg)
To close the seat, lower the seat and press down until it is
secured by the latch. Gently lift up on the seat to make sure it
is locked before riding.
Never exceed the maximum weight limit of the storage
compartment, as vehicle handling and stability may be
severely affected. Do not leave the ignition switch key
under the seat.
Turn signal switch:
Use the turn signal indicator to signal to other traffic that you
intend to turn or change lanes. The turn signal light on the
dash will flash to indicate that the switch is engaged.
66
66
6 Slide the turn switch to the left to activate the left turn
signal.
77
77
7 Slide the turn switch to the right to activate the right turn
signal.
To cancel the turn signal, press down on the signal switch 8.
Horn button
99
99
9:
Press the horn button to sound the horn.
NOTE: The horn will only sound when the ignition is “ON”.
CONTROLS & FEATURES
ATAT
ATAT
AT
66
66
6
77
77
7
88
88
8
99
99
9
13
CONTROLS & FEATURES
Helmet posts
Your scooter has two helmet posts AK so you can secure your
helmet(s) outside of the under-seat storage compartment.
With the seat up, put the helmet’s retaining ring onto the helmet
post. Lower and press down on the seat to lock it and secure the
helmet in place. To remove the helmet, open the seat.
Do not ride your scooter with a helmet hanging from a
helmet post, as this can interfere with your ability to con-
trol your scooter, and may cause an accident.
The under-seat storage compartment may become warm
from engine heat. Therefore, do not store any items in
this compartment that are susceptible to heat damage,
such as food or flammable materials.
Main stand
(center stand)
Your Agility scooter is equipped with a main (center) stand.
Always park your the scooter on firm, level ground to
help prevent it from falling over. If you must park on an
incline, aim the front of your scooter uphill.
To park your scooter on the main stand, stand on the left side
of the scooter and grasp the handlebar with your left hand,
while grasping the side of the rear rack with your right hand.
Step down on the foot pad of the main stand with your foot
while pulling up and back on the rear rack. This lifting motion
will allow the scooter to rock backwards and up onto the main
stand.
AKAK
AKAK
AK
AKAK
AKAK
AK
14
CONTROLS & FEATURES
1 1
1 1
1 Odometer: Indicates the total riding mileage of the scooter.
22
22
2 High Beam Indicator Light: This light is illuminated when
the headlight high beam is on.
33
33
3 Clock: Indicates the time (24-hour format).
4 4
4 4
4 Turn Signal Indicator Light: Flashes when either turn
signal is being used.
55
55
5 Speedometer: Indicates the road speed in MPH (miles
per our) and K/PH (kilometers per hour).
66
66
6 Fuel Gauge: This gauge indicates the amount of gasoline
in the fuel tank. Refill the tank with unleaded gasoline be-
fore the needle reaches the “E” (empty) mark. (Best prac-
tice is to maintain the fuel level no lower than the one-
quarter mark above empty whenever possible).
Instruments
22
22
2
33
33
3
44
44
4
11
11
1
55
55
5
66
66
6
Your Agility scooter is equipped with a digital clock 7. To set the
clock, follow this procedure:
1. Press and hold the SETTING BUTTON 8 until the clock’s
hour display begins to flash.
2. Press the ADJUST BUTTON 9 to change the clock’s hour
to the desired setting.
3. Press the SETTING BUTTON again so that the clock’s
minute display is flashing.
4. Press the ADJUST BUTTON to adjust the minute setting.
5. Once the desired time is set, press the SETTING BUTTON
once again to finalize your adjustments to the clock’s set-
tings and to release the clock from the adjustment mode.
77
77
7
88
88
8
99
99
9
Digital clock
15
CONTROLS & FEATURES
Passenger foot rest
The floorboard of your Agility scooter is equipped with a raised
section AT and floorboard area for use when you are carrying a
passenger.
Riding with a passenger will change the handling char-
acteristics of your scooter. Allow for extra braking dis-
tance and use extra care when riding in traffic.
Be sure you and your passenger always wear an ap-
proved motorcycle helmet that fits properly. You should
also wear eye protection and other protective apparel
when you ride.
ATAT
ATAT
AT
16
Break-in recommendations
The first 600 miles (1,000 km) of riding are the most important
in the life of your scooter. Following proper break-in proce-
dures during this time will help ensure maximum life and per-
formance from your new scooter. Proper break-in operation
allows the machined surfaces to polish each other and mate
smoothly.
Your scooter’s reliability and performance depend on your
exercise of special care and restraint during the break-in pe-
riod. It is especially important that you avoid operating the
engine in a manner which could expose the engine parts to
excessive heat.
The following guidelines should be followed during the break-
in period:
Maximum throttle operation:
Initial 300 miles (600 km): ........ Less than 1/2 throttle
Up to 600 miles (1,000 km): ..... Less than 3/4 throttle
Vary the engine speed:
The engine speed should be varied and not held at a constant
rate for long periods of time. This allows the parts to be "loaded"
with pressure, and then unloaded, allowing the parts to cool.
This aids in the mating process of the engine and transmis-
sion components. It is essential that some stress be placed on
these components during break-in to ensure that this mating
process occurs. Do not, however, apply excessive load on the
scooter's drive line.
Avoid constant low speed:
Operating the engine at constant low speed (light load) can
cause parts to glaze and not seat in properly. Allow the engine
to accelerate freely through the gears, without exceeding the
recommended throttle openings.
Avoid using full throttle for the first 300 miles (500 km).
The initial service:
The 200 mile (300 km) initial service is the most important
service your scooter will receive. Take extra care to observe
your scooter’s initial service in a timely fashion. During
the break-in period, all of the engine components will have
worn in, and all of the other parts will have seated in, so ad-
justments will be required. All fasteners will be tightened, and
the contaminated engine oil will be replaced.
NOTE: Completion of the 200 mile (300 km) initial service
will ensure optimum service life and performance from
your scooter. Do not delay in having this service performed
SECTION 3 -
OPERATION
17
Breaking in the new tires
New tires need proper break-in to assure maximum perfor-
mance, just as your scooter's engine does. Wear in the tread
surface by gradually increasing your cornering lean angles
over the first 100 miles (160 km) before attempting maximum
lean angles. Avoid hard acceleration, hard cornering, and hard
braking for the first 100 miles (160 km).
The 200 mile (300 km) service should be performed as
outlined in the maintenance schedule section of this
owner's manual. Pay particular attention to the cautions
and warnings in the Maintenance Schedule section.
Unless you have formal training as a service techni-
cian and have access to KYMCO technical reference
materials, it is strongly suggested that you have the
initial service performed by a KYMCO dealer.
Failure to break in your tires could cause the tires to
slip and could result in you losing control of the scooter.
Use extra care when riding on new tires. Perform proper
break-in of the tires as described in this Owner’s Manual
and avoid hard acceleration, hard cornering, and hard
braking for the first 100 miles (160 km).
OPERATION
Troubleshooting
It can be fustrating if your scooter fails to start or stops running
while your are riding. In the rare instance this occurs, take a
few moments to check the following items. This checklist cov-
ers some of the most common, simple problems which may
arise and which can be quickly resolved.
Do you have enough gasoline in the fuel tank?
Did you follow the correct procedure for starting the
engine?
Is the battery voltage low (you may need to kick start
your scooter)?
Is the main fuse in good condition?
NOTE: Use this Owner’s Manual to check components and
adjustments that are within your technical ability. If you
cannot resolve the problem, do not hesitate to contact your
KYMCO dealer for assistance.
18
Improperly maintaining your scooter or failing to cor-
rect a problem before riding can cause a crash in which
you can be seriously hurt or killed.
Always perform a pre-ride inspection before every ride
and correct any problems.
6. Steering: Check for smooth operation in all steering posi-
tions (page 23).
7. Instruments: Make sure the speedometer, fuel level gauge
and indicator lights function (page 23).
8. Lights and horn: Check that headlight, tail/brake light, turn
signals, indicators and horn function properly (page 24).
9. Chassis: Check for overall proper function (page 25).
1. Engine oil level: Add engine oil if required (page 19). Check
for leaks.
2. Front and rear brakes: Check operation, making sure there
is proper free-play at the left lever
, and that there is brake
fluid in the front brake fluid reservoir (pages 19 & 20).
3. Tires: Check condition and inflation pressure (pages 20 & 21).
4. Fuel level: Fill fuel tank when necessary (page 22). Check
for leaks.
Performing pre-ride inspections does not take the place
of regular maintenance. Follow the maintenance sched-
ule recommendations on pages 33 - 50 of this manual.
After one month of use or 200 miles (300 km) of riding,
which ever occurs first, contact your KYMCO dealer to
have an initial service of your scooter performed.
This initial service is most important service in the life
of your scooter and includes checks and adjustments
that will help ensure that your scooter operates effi-
ciently and safely
.
OPERATION
Pre-ride inspection (PRI)
For your safety, it is very important to take a few moments
before each ride to walk around your scooter and check its
condition. If you detect any problem, be sure to address it im-
mediately, or have it corrected by your KYMCO dealer.
19
OPERATION
1. Unscrew the dip stick 1, remove it and wipe it with a clean
cloth
2. Reinsert the dip stick until the threaded part of the dip stick
touches the engine case.
Do not thread the dipstick into the
engine case.
3. Remove the dip stick again and inspect the oil level on the
stick. The engine oil level should be above the "L" mark but
not higher than the "F" mark. Add or remove oil as required.
Do not overfill the engine with oil. Overfilling the en-
gine can cause oil leaks and/or oil contamination of
the air filter element. Always make sure the oil level is
above the "L" mark but not higher than the "F" mark.
PRI - Engine oil level inspection
NOTE: Park your scooter on the main stand, on level ground.
L
F
Use extreme caution when performing the oil level in-
spection or any other checks if the scooter’s engine
has been recently run. The engine oil, engine case and
muffler can become very hot creating a burn hazard.
PRI - Rear brake lever inspection (left lever)
1. Measure the free-play at the left brake lever end:
0.4 - 0.6 in (10 - 20 mm).
2. Use the cable adjuster on left brake lever perch for minor
free play adjustment.
Your scooter requires the proper brake lever free-play so the
brakes will be responsive and will not drag, causing prema-
ture wear to the brake pads. The free-play is the measured
distance between the brake lever at rest and the point at which
the brake first begins to engage.
11
11
1
0.4 - 0.6 in
(10 - 20 mm)
20
PRI - Tire inspection
The condition of your scooter’s tires is vital for operational ef-
ficiency and your safety. Check the tires’ inflation pressure,
the tread depth, and for damage before each ride.
1. Measure and adjust the tire pressure when the tires are
touching the ground (with no person on the scooter).
NOTE: Measure the pressure before riding as the heat gen-
erated during operation may cause improper readings.
Front tire (rider only): 17.5 PSI (1.25 kg/cm
2
)
Rear tire (rider only): 29.0 PSI (2.0 kg/cm
2
)
Front tire (rider & passenger): 17.5 PSI (1.25 kg/cm
2
)
Rear tire (rider & passenger): 32.0 PSI ( 2.25 kg/cm
2
)
PRI - Front brake lever & fluid inspection
(right lever)
The right brake lever on your Agility scooter controls the front
hydraulic brake. Check the free-play at the end of the lever so
the brake will be responsive and will not drag, which could
cause premature wear to the brake pads or brake rotor.
OPERATION
1. Measure the free-play at the right brake lever end:
0.4 - 0.6 in (10 - 20 mm).
2. Verify that the fluid level is between the “L” mark 1 and the
“F” mark 2 in the brake fluid reservoir window. See the
MAINTENANCE section of this Owner’s Manual for addi-
tional information about the front brake fluid.
See your KYMCO dealer immediately if the front brake le-
ver free-play is not within specification.
22
22
2
11
11
1
21
OPERATION
2. Inspect the tires for nails, screws and other objects 3 that
may be imbedded into the rubber.
33
33
3
3. Check the tread depth 4 at the wear indicator points 5. If
the tread is worn smooth at these points, the tire must
be replaced.
44
44
4
55
55
5
55
55
5
4. Check for damage 6 (blisters or cuts) in the side wall, or
for significant flat spots 7 on the tires’ tread. Replace the
tire immediately if any damage of this type is present.
66
66
6
66
66
6
77
77
7
The tires on your scooter must be replaced if they:


 Leak air (even at a slow rate)


 Have any damage on the tread or side wall areas


Have been damaged by intrusion of objects, such as a nail


 Are worn as evidenced by the wear indicators
Failure to replace a tire in poor condition will cause an
unsafe riding condition on your scooter. Replace worn or
damaged tires immediately for your, and your passenger’s,
safety.
Consult your KYMCO dealer for replacement tire service.
22
OPERATION
PRI - Fuel level inspection / Refilling
To open the fuel filler cap:
1. With the engine “OFF”, place the scooter on its main stand
and open the seat (see page 12 of this manual).
When the fuel level gauge needle approaches “E” (indicating
the tank is nearly empty) refill the tank with unleaded gasoline.
Do not overfill the tank. There should be no fuel in the
fuel filler neck. Excess fuel can contaminate the evapo-
rative emission canister, resulting in poor drivability.
Fuel recommendation
Use unleaded gasoline with a research octane number of 91
or higher. Unleaded gasoline will extend spark plug life.
Gasoline is highly flammable and explosive. You can be
burned or seriously injured while handling fuel.
* Stop the engine and keep heat, sparks, and flame away.
* Refuel only out doors.
* Clean up fuel spills immediately.
2. Insert the ignition switch key into the lock on the fuel filler
cap 1 and rotate the key counterclockwise to unlock and
open the cap.
3. Add fuel (per the recommendations listed in this manual).
11
11
1
4. Replace the fuel filler cap by aligning the tabs on the cap
with the slots in the fuel filler neck.
5. When closing the cap, press down on the cap slightly and
rotate the ignition switch key clockwise to lock the cap into
place.
6. Remove the key from the fuel filler cap and close the seat.
23
OPERATION
1. Visually inspect the handlebars for any damage.
2. Apply the front brake (right lever) and press down and re-
lease pressure on the handlebar, listening for any abnormal
noise.
3. As you press down and release, also feel for any looseness
from the chassis transmitted to the handlebar.
4. Turn the handlebar from the center fully to the left and then
fully to the right, feeling for any loose components and lis-
tening for any abnormal sounds.
PRI - Steering & handlebar inspection
Before riding, inspect your scooter’s handlebars for damage,
and make sure the steering’s side-to-side and up-and-down
movement is smooth.
If you detect any looseness or abnormal sounds dur-
ing your steering inspection, do not ride your scooter.
Consult your KYMCO dealer for chassis service.
PRI - Instrument inspection
Before your ride, and as you begin your ride, make sure the
instruments are functioning.
1. Do the indicator lights 1 (turn signal, for example) function?
2. Does the speedometer 2 needle move as the scooter moves?
3. Does the fuel level gauge needle 3 indicate the fuel level?
11
11
1
22
22
2
33
33
3
NOTE: Contact your KYMCO dealer for repair of your
scooter’s instruments if they are not functioning properly.
24
1. Turn the ignition switch to “ ON“ and press the horn button
on the left handlebar switch to check if it sounds.
OPERATION
2. Turn on the headlight switch to see if the headlight 1 and
the tail light 3 are illuminated. Check the lenses for dirt or
damage.
3. Operate the turn signal switch to make sure the turn signals
2 flash. Make sure each of the four signals flash and the
lenses are free of dirt and are not broken.
4. Squeeze each brake lever to make sure the brake lamp in
the tail light 4 illuminates.
The horn is an essential safety item, as it alerts other
traffic to your presence.
The headlight must be in good working order to illumi-
nate your riding path at night.
The tail/brake light is required so others in traffic can
see your scooter and be alerted to your intention to stop
or slow down.
The turn signals indicate your turning intentions.
Because all of these systems are vital safety items, con-
tact your KYMCO dealer for replacement bulbs or elec-
trical system service or repair should there be any mal-
functions.
PRI - Horn & lights inspection
11
11
1
22
22
2
33
33
3
25
PRI - Chassis inspection
Complete the pre-ride inspection of your scooter by checking
items on its chassis.
OPERATION
Front suspension & rear shock absorber: Check the op-
eration of the suspension by pressing down on the handlebars
and seat. Make sure the suspension returns in a smooth fash-
ion.
Brake lever operation: Check that the rear brake (left lever)
and the front brake (right lever) have pressure and lock the
wheels when you squeeze the levers.
Mirrors: Adjust the mirrors while seated on the scooter BE-
FORE you begin riding.
License plate: Make sure your license plate is securely
mounted and your registration is current.
Reflectors: Look to make sure all of the safety reflectors are
still mounted to your scooter. Replace any missing or dam-
aged reflectors.
Lubrication points: Occasionally check and lubricate certain
controls and points on the scooter as called out in the periodic
maintenance schedule (see pages 24 & 35).
26
OPERATION
Starting the engine (electric start)
To start your scooter using the electric starting motor, follow
this procedure:
1. Unlock the steering with the ignition switch key and turn the
ignition switch to “ON“.
NOTE: Before starting, check the engine oil and fuel lev-
els. Take the scooter off of the main stand.
2. Apply the rear brake (left lever) .
The brake must be adjusted and functioning properly
to lock the rear wheel during starting or the scooter
could accelerate away when the engine starts.
To prevent damage to the starter motor, do not operate
the starter motor for more than five seconds at a time. If
the scooter fails to start immediately, check the fuel level
and the battery condition, and allow the starter motor to
cool before attempting to start the engine again.
3. Press the starter button 1 without rotating the throttle grip.
NOTE: If the scooter’s engine is warm and does not start
immediately, rotate the throttle grip to 1/8 to 1/4 open to
help the engine start.
NOTE: The rear brake must be held for the starter motor
to engage the engine. It is normal for the stop light to be
illuminated during starting.
11
11
1
27
OPERATION
Your scooter's exhaust emits poisonous carbon mon-
oxide gas. High levels of carbon monoxide can collect
rapidly in enclosed areas such as a garage. Do not run
the scooter's engine with the garage door closed. Even
with the door open, run the engine only long enough
to move your scooter out of the garage.
3. While squeezing the rear brake lever, kick down on the
kick start lever without rotating the throttle grip.
Once the scooter starts, the rear wheel may spin. To
avoid injury, keep your body and clothing away from
the rear wheel.
NOTE: If the scooter has not been ridden for a long pe-
riod of time it may be hard to start. Add fresh fuel and
press the starter button several times in succession to
try to start the engine. If the scooter does not start, con-
tact your KYMCO dealer as your scooter may need to have
its fuel system cleaned and adjusted.
Do not press the starter button once the engine is run-
ning or the starter motor and engine may be damaged.
Starting the engine (kick start)
To start your scooter using the kick start lever, follow the elec-
tric starting procedure, except use the kick lever in place of the
electric start button.
4. Allow a cold engine to warm up 2 - 3 minutes before riding.
NOTE: If the scooter’s engine is warm and does not start
immediately, rotate the throttle grip to 1/8 to 1/4 open to
help the engine start.
Once the scooter is started, fold the kick start lever
back to its original position.
28
OPERATION
Riding your scooter
NOTE: After starting, allow the engine oil to circulate be-
fore riding your scooter. Allow sufficient idling time after
warm or cold engine start-up before applying load or rev-
ving the engine. This allows time for the lubricating oil to
reach all the critical engine components.
NOTE: Review the scooter safety recommendations on
pages 2 through 6 before you ride.
Make sure flammable materials such as dry grass or
leaves do not come into contact with the exhaust sys-
tem when riding, idling, or parking your scooter
.
1. Make sure the throttle is closed and the rear brake is en-
gaged before moving the scooter off the main stand.
You and your passenger should always wear appropriate
safety apparel such as a helmet, eye protection, gloves
and other protective clothing each time you ride the scooter.
Never wear any items that will adversely affect your safety.
2. Mount the scooter from the left side and sit in an upright
position on the seat. Place both hands on the handlebars
and touch the ground with your left foot 1 for stability.
3. Release the rear brake and slowly rotate the throttle grip
so that the engine power will be transmitted smoothly to
the rear wheel.
Use the scooter’s turn signals to signal your intention to
merge into traffic. Always scan around you and check the
rear view mirrors so you are aware of other traffic. Use
caution as you merge into traffic, keeping to the right until
you match the pace of the traffic.
11
11
1
29
OPERATION
4. Control the scooter’s speed with the throttle grip.
Rotating the grip towards you 2 will increase the scooter’s
speed.
Rotating the grip away from you will decrease the scooter’s
speed.
5. Limit the maximum speed of your scooter during the first
600 miles (1,000 km) of operation. Keep the road speed
below 25 MPH (40 KPH) during this break-in period.
In hot weather the engine could overheat if it idles for a
long period of time. Very slow speed traffic could also
cause the scooter to overhead. To promote engine lon-
gevity permit the engine to cool in these situations.
Avoid sudden acceleration and prolonged high speed
use that can accelerate engine wear.
Moderate use will prolong the engine life of the scooter.
22
22
2
6. Use both brake levers when slowing and stopping the
scooter. Release the throttle when braking.
NOTE: Decreasing the scooter’s speed with a balanced
application of both brake levers and a reduction of throttle
will reduce the distance required to stop. Squeeze the le-
vers lightly at first and then increase the pressure when
stopping.
Avoid using just one brake to stop the scooter, as this will
affect the tires’ grip.
Avoid sudden braking as this will also affect the tires’ grip
and can cause an accident.
30
OPERATION
NOTE: At certain speeds your scooter will turn more ef-
fectively by leaning your body, than by applying pressure
on the handlebars. Practice steering in an open, traffic-
free area until you are familiar with the handling charac-
teristics of your scooter.
Reduce your speed when riding on uneven or loose road
surfaces. When riding downhill, use less throttle and inter-
mittently brake to control the vehicle’s speed. These con-
ditions reduce tire grip and can cause an accident.
Reduce your speed when riding your scooter in the rain.
Wet road surfaces reduce tire grip and greatly increases
the distance required for safe braking. The wet surface
also reduces tires grip during cornering. Reduced tire grip
will make it more difficult to control your scooter and may
cause an accident.
8. As you approach a turn, or plan to stop, use the turn sig-
nals well in advance to alert other traffic of your intentions.
Scan for other vehicles around you and slowly move to the
right side of the road. Close the throttle, apply the brake
smoothly, as the brake light will warn vehicles behind you
that you are braking.
7. When riding and turning the scooter, use smooth move-
ments.
31
OPERATION
9. When you stop the scooter, press the center of the turn
signal indicator switch to cancel the signal flashing. Turn
the ignition switch to the “OFF“ position to stop the engine
and turn off the scooter’s electrical system.
Never operate the ignition switch while riding your scooter.
If the ignition switch is turned during riding it could turn
off the engine and lights, possibly causing you to lose con-
trol of the scooter.
With the lights off, your scooter may not be visible to other
traffic, and this could cause a traffic accident.
Only operate the ignition switch when the scooter is not
moving.
Parking your scooter
Use the following procedure and suggestions when parking
your scooter.
1. Place the scooter on level ground.
2. Stand on the left side of the scooter and grasp the handle-
bar with your left hand, while grasping the side of the rear
rack with your right hand. Step down on the foot pad of the
main stand with your foot while pulling up and back on the
rear rack. This lifting motion will allow the scooter to rock
backwards and up onto the main stand.
32
OPERATION
The scooter may fall over if it is not parked on level
ground.
Make sure flammable materials such as dry grass or
leaves do not come into contact with the exhaust sys-
tem when parking your scooter.
Lock the steering of your scooter (see pages 9 & 10) to
reduce the risk of theft.
Do not park your scooter in a place that hinders traffic,
or that is unsafe to you or others.
33
SECTION 4 -
MAINTENANCE
The importance of maintenance
Maintaining your scooter properly is essential for safe, eco-
nomical and trouble-free riding. It will also help reduce air pol-
lution and maximize fuel economy.
To help you properly care for your scooter, the following pages
in this Owner's Manual include a maintenance schedule to
help you make sure your scooter is serviced at the appropri-
ate intervals.
These instructions are based on the assumption that your
scooter will be used exclusively for its designed purpose. Sus-
tained, high-speed operation, or operation in unusually wet or
dusty conditions, will require more frequent service than speci-
fied in the maintenance schedule. Consult your KYMCO dealer
for recommendations applicable to your individual needs and
use.
NOTE: Always follow the inspection and maintenance rec-
ommendations and schedules in this Owner's Manual.
When performing maintenance on your scooter you may
need to start the engine. Running your scooter's en-
gine indoors or in a garage can be hazardous. Exhaust
gas contains carbon monoxide, a gas that is colorless
and odorless, and can cause death or severe injury.
Operate the engine only where there is adequate venti-
lation, preferably outdoors.
If your scooter tips over or becomes involved in a crash,
be sure your KYMCO dealer inspects all major parts,
even if you are able to make some repairs.
Improperly maintaining this scooter or failing to cor-
rect a problem before you ride could result in a crash in
which you could be seriously hurt or killed.
34
MAINTENANCE
Maintenance Schedule
Perform the pre-ride inspection (see pages 18 - 25) at each scheduled maintenance period. This interval should be judged by
odometer reading or months, whichever comes first.
Maintenance Schedule Legend (see page 35):
I: INSPECT AND CLEAN, ADJUST, LUBRICATE OR REPLACE IF NECESSARY
C: CLEAN R: REPLACE A: ADJUST L: LUBRICATE T: TIGHTEN
The maintenance schedule on page 35 specifies the maintenance required to keep your Agility scooter in peak operating
condition. Maintenance work should be performed in accordance with KYMCO standards and specifications by properly trained
and equipped technicians. Your KYMCO dealer meets all of these requirements.
* Should be serviced by your KYMCO dealer, unless you have the proper tools, service data and are technically qualified.
* * In the interest of safety, we recommend these items be serviced only by your KYMCO dealer. KYMCO USA recommends
that your KYMCO dealer road test your scooter after each periodic maintenance service is completed.
Maintenance Schedule Notes (see page 35):
1. At higher odometer readings, repeat at the frequency interval listed here.
2. Service more frequently if the scooter is ridden in unusually wet or dusty areas.
3. Service more frequently when riding in rain or at full throttle.
4. “PRI” indicates that the item should be checked as part of the Pre-Ride Inspection (see page 18 through 25)
5. “See page” indicates on which page of the Owner
’s Manual you will find information about the required maintenance.
6. “Dealer” indicates maintenance or service procedure that should be performed by your KYMCO dealer.
35
MILEAGE
200 mi 600 mi 1850 mi 3100 mi 4300 mi 5500 mi 7000 mi Pre-ride See
ITEM
300 km 1000 km 3000 km 5000 km 7000 km 9000 km 11000 km inspection page
Engine oil * R R R R R R R PRI 19, 40
Engine oil strainer * C - C - C - C - 40
Gear oil * R - R - R - R - 42
Spark plug * C I C R C I R - 43
Valve clearance ** A - A - A - A - Dealer
Carburetor ** I - I - I - I - Dealer
Drive belt ** - - - - I - - - Dealer
Air cleaner * C I R I R I R - 37
Battery * I I I I I I I PRI 38, 39
Fuel filter ** - - - - R - - - Dealer
Brake system ** I I I I I I I PRI 19, 43
Tires ** I I I I I I I PRI 20, 36
Bolts & nuts * T I I T I I T PRI 25
Maintenance Schedule - Agility 50 & 125
MAINTENANCE
I: INSPECT AND CLEAN, ADJUST, LUBRICATE OR REPLACE IF NECESSARY
C: CLEAN R: REPLACE A: ADJUST L: LUBRICATE T: TIGHTEN
36
MAINTENANCE
Tires
NOTE: Check the tire inflation pressure and tire tread con-
dition at the periods listed in the Periodic Maintenance
Schedule. For maximum safety and good tire life, the tire
pressures should be inspected more often.
Failure to follow these warnings may result in an acci-
dent due to tire failure. The tires on your scooter are a
crucial link between your scooter and the road. You and
your passenger's personal safety are dependant upon
the condition of your scooter's tires.
Follow these instructions:
Check tire condition and pressure, and adjust the
inflation pressure before each ride.
Avoid overloading your scooter.
Replace a tire when worn to the specified limit, or
if you find any damage such as cuts or cracks.
Always use the proper size and type of tires as
specified in this Owner's Manual.
Balance the wheel after tire installation.
Read this section of Owner's Manual carefully.
Failure to perform a reasonable break-in of the tires
could cause tire slip and loss of control.
Use extra care when riding on new tires, as the grip
will be limited. Perform proper break-in of the tires, as
set forth in the break-in recommendation section of this
manual. Avoid hard acceleration, hard cornering, and
hard braking for the first 100 miles (160 km).
Tire pressure
Insufficient air pressure in the tires not only accelerates tire
wear, but it also affects the stability of your scooter. Under-
inflated tires make smooth cornering difficult, and overinflated
tires decrease the amount of tire in contact with the ground,
which can lead to skids and loss of control. Make sure that the
tire pressures on your scooter are within the specified limits at
all times.
NOTE: Tire pressure should only be adjusted when the
tires are cold.
Front tire (rider only): 17.5 PSI (1.25 kg/cm
2
)
Rear tire (rider only): 29.0 PSI (2.0 kg/cm
2
)
Front tire (rider & passenger): 17.5 PSI (1.25 kg/cm
2
)
Rear tire (rider & passenger): 32.0 PSI ( 2.25 kg/cm
2
)
37
MAINTENANCE
Air cleaner filter element
The air cleaner filter element should be serviced at regular
intervals. Service the element more often when riding in un-
usually wet or dusty areas.
1. Open seat (see page 12).
2. Remove air cleaner cover screws 1.
3. Remove the air cleaner case cover 2.
4. Remove the air cleaner element
5. If lightly soiled, clean the filter 3 with compressed air. If very
dirty (or if the filter is at the replacement interval per the main-
tenance schedule) discard the air cleaner element.
6. Install the cleaned or new air cleaner element. Use the
KYMCO genuine air cleaner element or an equivalent air
cleaner element specified for your scooter.
7. Complete the installation by reinstalling the air cleaner parts in
the reverse order of removal.
Improper installation for the filter can cause water or
dirt to enter the engine causing premature wear.
Using the wrong KYMCO air cleaner element or a non-
KYMCO air cleaner element which is not of equivalent
quality may cause premature engine wear or perfor-
mance problems.
11
11
1
22
22
2
33
33
3
38
MAINTENANCE
Fuel system & hoses
Check the fuel hoses and fittings for any signs of leakage.
1. Check for leakage at the carburetor 1.
2. Check for leakage from the fuel hoses, clamps and joints 2.
3. Check for leakage at the fuel filter 3.
4. Check for leakage at the fuel tank 4.
Replace any fuel system components that are leaking fuel.
Contact your KYMCO dealer for fuel system service and
repairs.
Battery
Your KYMCO scooter is equipped with a maintenance-free
(sealed) battery. Therefore, it is not necessary to check the
battery's electrolyte level or add distilled water.
NOTE: If your battery seems weak and/or is leaking elec-
trolyte (causing hard starting or other electrical troubles),
contact your KYMCO dealer immediately .
Your battery is a maintenance-free type and can be per-
manently damaged if the cap strip is removed.
Charge the battery with a charger specifically designed
for use with a maintenance-free type battery. Using an-
other type of charger can damage the battery.
Your scooter's battery gives off explosive hydrogen gas
during normal operation. A spark or flame can cause
the battery to explode with enough force to kill or seri-
ously injure you. Wear protective clothing and a face
shield, or have a qualified technician perform the bat-
tery maintenance.
11
11
1
22
22
2
33
33
3
44
44
4
39
MAINTENANCE
Battery removal & installation
The battery 5 is in the battery box below seat.
Fuses
When frequent fuse failures occur, it usually indicates a short
circuit or an overload in the electrical system.
Fuse replacement
FUSE SIZE: 7A
(One MAIN fuse & one SPARE)
NOTE: See your KYMCO dealer for electrical system
diagnosis and repair.
Never use a fuse with a different rating from that speci-
fied. Serious damage to the electrical system or a fire
hazard may result, causing a dangerous loss of lights
or engine power.
1. When removing the battery for charging or replacement, dis-
connect the negative (-) terminal lead from the battery first,
then disconnect the positive (+) terminal lead.
2. When installing the battery, connect the positive terminal
lead (+) first, then the negative terminal lead (-).
1. Open the fuse holder 6.
Pull the fuse holder clips
7 out of the holder.
2. Slide the fuse 8 out of
the holder clips.
3. Install a new fuse 8 of
the proper specification
into the holder clips.
4. Press the fuse and the
holder clips 7 back into
the holder.
5. Close the fuse holder 6
and set it back in place.
66
66
6
66
66
6
77
77
7
88
88
8
88
88
8
77
77
7
NOTE: Always keep ignition switch OFF when servicing
the battery.
55
55
5
40
Engine oil
Engine oil recommendation
Use a premium quality 4-stroke engine oil to ensure longer
service life of your scooter. Only use oils that have a SJ rating
per the API service classification.
Engine oil capacity: 0.95 qt (0.9 L)
Engine oil viscosity: SAE 15W-40
If this viscosity is not available, select an alternative engine
oil according to the chart shown below.
ENGINE OIL VISCOSITIES
Engine oil level inspection
Check the engine oil level each day before riding your scooter
(see page 19).
The engine and related components can become very hot.
Use care when inspecting or adjusting the oil level to avoid
injury. If needed, let the engine and exhaust system cool
before working in those areas.
Prolonged contact with used engine oil can cause skin
cancer. Although rare, this possibility exists if you handle
oil on a frequent basis. Thoroughly wash your hands with
soap and water as soon as possible after handling used
oil.
Engine oil replacement
Engine oil quality is the primary factor affecting engine longev-
ity. Change your scooter's engine oil as specified in the main-
tenance schedule (see page 35).
NOTE: When riding your scooter in very dusty conditions,
oil changes should be performed more frequently than
specified in the maintenance schedule.
NOTE: Always dispose of used engine oil in a environ-
mentally responsible manner. You should take the drained
oil in a sealed container to your local recycling center or
service station for reclamation. Do not throw the oil in the
trash, pour it on the ground, or pour it down a drain.
NOTE: Change the engine oil with the engine at normal
operating temperature, with the scooter positioned on its
main stand, to assure complete and rapid draining.
MAINTENANCE
41
1. Place a suitable container (drain pan) under the left crank-
case. Remove the drain bolt 1 to drain the oil.
3. Replace the drain bolt 1. Tighten it to the specified torque.
Do not overfill the engine with oil. Overfilling the en-
gine can cause oil leaks and/or oil contamination of
the air filter element. Always make sure the oil level is
above the "L" mark but not higher than the "F" mark
on the dipstick.
Engine oil capacity: 0.95 qt (0.9 L)
Engine oil viscosity: SAE 15W-40
5. Refer to page 19: Wipe the dipstick 2 o
ff with a clean cloth
and reinstall it in its hole, but do not thread it into the engine
case. Push the dip stick in until it touches the case.
6. Remove the dip stick and visually inspect the oil level on the
stick. The engine oil level should be above the "L" mark but
not higher than the "F" mark. Add or remove oil as required.
7. Replace the oil filler/dipstick and tighten it securely.
MAINTENANCE
Oil drain plug torque: 18 lb-ft (25 N-m)
4. Add engine oil through the oil filler/dipstick hole.
11
11
1
2. Remove the oil filler/dipstick 2 from the right crankcase
cover.
22
22
2
42
MAINTENANCE
Transmission fluid change
1. Place the scooter on its main stand.
3. After the fluid has drained out, reinstall the drain bolt with a
new sealing washer and tighten it to the specified torque.
2. Place a suitable container (drain pan) under the transmis-
sion case on its left side. Remove the drain bolt 1 to
drain the fluid.
Transmission fluid type: SAE 90
Transmission fluid capacity (Agility 50): 0.12 qt (0.11 L)
Transmission fluid capacity (Agility 125): 0.21 qt (0.20 L)
NOTE: The fill amount specified is the amount to use after
completely draining the used transmission fluid.
Transmission fluid drain bolt torque: 15 lb-ft (20 N-m)
4. Remove the transmission fluid filler bolt 2.
5. Add the
exact specified fluid through the fluid filler hole 3.
Using the wrong transmission fluid type or viscosity
may cause premature transmission component wear.
Do not exceed the specified amount when adding trans-
mission fluid. If too much fluid is added to the trans-
mission case it could be forced into the air cleaner as-
sembly during operation, causing air filter contamina-
tion and poor engine performance.
11
11
1
22
22
2
33
33
3
43
MAINTENANCE
Spark plug
Remove the carbon deposits from the spark plug
with a small wire brush or a spark plug cleaning
machine. After cleaning (or when installing
a new spark plug) readjust the spark plug
gap to specified limit by using a spark plug
gap thickness gauge. The spark plug
should be replaced periodically. Under nor-
mal usage, a spark plug's porcelain tip should
appear light brown or tan in color. If the spark plug porcelain
tip is very white or glazed appearing, then the spark plug has
been operating too hot. In such a situation, you
should replace the standard spark plug with a spark
plug that has a colder heat range (usually a higher
number; consult with your KYMCO dealer when
selecting an alternate spark plug).
An improper spark plug may have an incorrect fit or
heat range for your engine. This may cause severe en-
gine damage which will not be covered under warranty.
Never use a spark plug with an improper heat range, as
severe engine damage may result.
Recommended spark plug
Spark plug type: CR7HSA
Spark plug gap: 0.024 - 0.028 in
(0.6 - 0.7 mm)
Brake fluid (front brake)
Your scooter is equipped with a hydraulic front brake. Check
the brake fluid level window on the master cylinder reservoir
on the handlebars per the maintenance schedule.
UPPER LEVEL
LOWER LEVEL (add)
1. Remove the two Phillips screws retaining the master cylin-
der cap. Remove the cap.
2. Add the specified type of brake fluid to bring the level up to
the “UPPER” level in the window.
3. Wipe the master cylinder cap and gasket with a clean cloth
and reinstall the cap, tightening the screws securely.
Adding brake fluid:
Brake fluid type: DOT 4
Do not allow brake fluid to touch the scooter’s body
work, as it will damage the painted surface.
Do not mix brake fluid types. Doing so may cause brake
failure and could result in an accident.
44
Brake shoe adjustment (rear brake)
Your scooter requires the proper lever free-play and brake
shoe adjustment so the rear brake will be responsive and will
not drag, causing premature wear to the brake shoes.
Make sure the rear wheel turns freely after free play
adjustment so the brake will function properly and not
wear prematurely.
MAINTENANCE
1. Measure the free-play at the left brake lever end 1:
0.4 - 0.6 in (10 - 20 mm).
2. Use the cable adjuster on left brake lever perch for minor
free play adjustment.
Note: The free-play is the measured distance between the
brake lever at rest and a fully applied brake.
11
11
1
22
22
2
33
33
3
44
44
4
55
55
5
4. Use the cable end adjuster 4 to set the free play
NOTE: If the brake arm pointer is outside of the adjust-
ment range markings
3 3
3 3
3 the brake shoes must be in-
spected and possibly be replaced by your KYMCO dealer.
NOTE: If the wear indicator grooves in the front brake pads
5 5
5 5
5 are no longer visible , it is an indication that the brake
pads are worn and require replacement. Consult your
KYMCO dealer for any brake-related service.
3. Adjust the rear brake major free play so the pointer on the
brake arm 2 is within the adjustment range markings 3
on the transmission case.
45
MAINTENANCE
Washing your scooter
1. Rinse the scooter thoroughly with cool water to remove any
loose dirt.
2. Clean the scooter with a sponge or soft cloth using cool water.
Avoid directing water at muffler outlets and electrical parts.
3. Clean the plastic parts using a cloth or sponge dampened with
a solution of mild detergent and water. Rub the soiled area
gently, rinsing it frequently with fresh water. Take care to keep
brake fluid or other chemical solvents away from the scooter,
as they will damage the plastic and painted surfaces.
NOTE: The inside of the headlight lens may become clouded
immediately after washing the scooter. Moisture condensa-
tion inside the headlight lens will disappear gradually as it is
heated by the headlight. After washing, run the engine while
keeping the headlight on to dissipate any condensation.
4. After cleaning, rinse the scooter thoroughly with plenty of
clean water. This rinsing is required to remove detergent
residue which can corrode alloy parts.
5. Dry the scooter and then start the engine, allowing it to run
for several minutes.
Cleaning
Clean your scooter regularly to protect the surface finishes
and inspect for damage, wear, and oil, coolant or brake fluid
leakage.
Avoid cleaning products that are not specifically designed for
scooter, motorcycle, or automobile surfaces. Nonspecific clean-
ers may contain harsh detergents or chemical solvents that
could damage the metal, paint, and plastic on your scooter.
NOTE: If your scooter is still warm from recent operation,
give the engine and exhaust system time to cool off be-
fore washing. Avoid the use of high pressure water spray
(typical in coin-operated car washes), as the powerful
spray can damage components on your scooter.
46
MAINTENANCE
6. Test the brakes before riding the scooter. Several applica-
tions of the brakes may be necessary to restore normal brak-
ing performance.
NOTE: Due to water on the brake components, braking
efficiency may be temporarily impaired immediately after
washing the scooter. Anticipate longer stopping distances
to avoid a possible accident.
Finishing touches:
After washing your scooter, consider using a commercially-
available spray cleaner/polish or a quality liquid or paste wax
to enhance and protect the paint's finish. Use only a nonabra-
sive polish or wax made specifically for scooters, motorcycles,
or automobiles. Apply the polish or wax according to the in-
structions on the container.
Removing road salt
The salt used in some communities to prevent road icing can
become very corrosive to your scooter. Wash your scooter as
soon as possible if it comes in contact with road salt (or sea
water).
1. Clean the scooter using cool water (see page 45). Do not
use warm water; as this will increase the corrosive effect of
the salt.
2. Dry the scooter and protect painted and metal surfaces
with wax or polish.
Painted aluminum wheel maintenance
Even if protected by paint, aluminum may corrode from con-
tact with dirt, mud, or road salt. Clean the scooter's wheels
with a wet sponge and mild detergent. Avoid stiff brushes, steel
wool, or cleaners containing abrasives or chemical compounds.
After washing, rinse with plenty of water and dry with a clean
cloth. Apply touch-up paint to the wheels where damage has
occurred.
Exhaust pipe maintenance
The exhaust system is stainless steel, but it can become stained
by oil or mud. If necessary, remove heat stains with a liquid
kitchen-counter abrasive.
47
MAINTENANCE
STORAGE GUIDE
Extended storage, such as for the winter months, requires that
you take certain steps to reduce the effects of deterioration
from the non-use of your scooter. Whenever possible, perform
any necessary periodic maintenance or repairs before storage
so the scooter will be in good condition for riding when it is
removed from storage.
Storage
1. Change the engine oil and filter.
2. Drain the carburetor (if equipped) and empty the fuel tank
into an approved gasoline container using a commercially
available hand siphon or an equivalent method. Spray the
inside of the tank with an aerosol rust-inhibiting oil. Close
the fuel filler cap on the fuel tank
Gasoline is highly flammable and explosive. You can
be burned or seriously injured when handling fuel. Stop
the engine and keep heat, sparks, and flame away. Re-
fuel the scooter outdoors and wipe up any spills imme-
diately.
3. To prevent rusting in the cylinder, perform the following:
Remove the spark plug cap from the spark plug, and use tape
or string to secure the cap to any convenient plastic body part
so that it is positioned away from the spark plugs.
Remove the spark plug from the engine and store it in a
safe, dry place. Do not connect the spark plug to the spark
plug cap.
Pour a tablespoon (15 - 20 cc) of clean engine oil into the
cylinder and cover the spark plug hole with a piece of cloth.
Crank the engine several times to distribute the oil.
Reinstall the spark plug and spark plug cap.
5. Remove the battery. Store it in an area protected from freez-
ing temperatures and direct sunlight. Slow charge the bat-
tery once a month (use a quality charger designed for use
on a maintenance-free type battery).
6. Wash and dry the scooter. Wax all painted surfaces. Coat
the chrome or bare aluminum parts with rust inhibiting oil.
7. Inflate the tires to their recommended pressures. Place the
scooter on blocks to raise both tires off the ground.
8. Cover the scooter (don't use plastic or other coated materi-
als) and store in an unheated area, free of excessive mois-
ture, with a minimum of daily temperature variation. Do not
store the scooter in direct sunlight, as the sun's UV rays
can damage the body work and other components.
48
Removal from storage
1. Uncover and clean the scooter.
2. Change the engine oil if more than 1 month has passed
since the start of storage.
3. Charge the battery as required (use a quality charger de-
signed for use on a maintenance-free type battery). Install
the battery.
4. Drain any excess aerosol rust-inhibiting oil from the fuel
tank. Fill the fuel tank with fresh gasoline.
5. Perform all the pre-ride inspection checks (see pages 18 -
25). T
est ride the scooter at low speeds in a safe riding
area, away from traffic.
49
MAINTENANCE RECORD
DATE MILEAGE SERVICE PERFORMED & NOTES
50
MAINTENANCE RECORD
DATE MILEAGE SERVICE PERFORMED & NOTES
51
SPECIFICATIONS - AGILITY 50
Dimensions
Overall length .......................................... 72.0 in (1830 mm)
Overall width.............................................. 27.1 in (690 mm)
Overall height .......................................... 44.5 in (1130 mm)
Wheel base...............................................52.1 in (1325mm)
Seat height ................................................29.0 in (790 mm)
Dry weight............................................... 202.8 lbs (92.0 kg)
Capacities
Engine oil .................................................0.95 US qt. (0.9 L)
Transmission oil............................................ 0.12 qt (0.11 L)
Fuel tank ................................................... 1.3 US gal (5.0 L)
Maximum weight capacity....................... 544.0 lbs (247 kg)
Engine
Type ...................................... Four-stroke, air-cooled SOHC
Displacement....................................... 49.5 cm3 (3.0 cu. in)
Bore and stroke ...............1.53in X 1.61 in (39 X 41.4 mm)
Compression ratio .......................................................... 11:1
Spark plug .............................................................. CR7HSA
Idle speed ............................................................ 2000 RPM
Cooling system............................................ Forced Air (fan)
Starting system... Electric starter motor (kick-start back-up)
Transmission ................................................ Automatic CVT
Chassis
Tire size, front..................................................... 120/70 - 12
Tire size, rear...................................................... 130/70 - 12
Chassis material................................................... Aluminum
Front suspension.........................................Telescopic forks
Rear suspension .............................. Single shock absorber
Brake (front) ...........................................................Disc type
Brake (rear) .................................................Drum/shoe type
Electrical
Ignition type ..............................................................DC-CDI
Battery ..................................................................... 12v-6Ah
Headlight ........................................................... 12v 35/35W
Tail/brake light ..................................................... 12v 5/21W
Turn signal light ................................................12v 10W X 4
Position light ........................................ 12v5W (front & rear)
Main Fuse......................................................................... 7A
52
SPECIFICATIONS - AGILITY 125
Dimensions
Overall length .......................................... 72.0 in (1830 mm)
Overall width.............................................. 27.1 in (690 mm)
Overall height .......................................... 44.3 in (1125 mm)
Wheel base..............................................51.7 in (1315 mm)
Seat height ................................................30.9 in (785 mm)
Dry weight................................................ 233.6 lbs (106 kg)
Capacities
Engine oil ............................................. .. 0.95 US qt. (0.9 L)
Transmission oil............................................. 0.21 qt (0.2 L)
Fuel tank ................................................... 1.3 US gal (5.0 L)
Maximum weight capacity.......................... 570 lbs (259 kg)
Engine
Type ...................................... Four-stroke, air-cooled SOHC
Displacement..................................... 124.6 cm3 (7.6 cu. in)
Bore and stroke .......... 2.06 in X 2.27 in (52.4 X 57.8 mm)
Compression ratio ..........................................................13:1
Spark plug .............................................................. CR7HSA
Idle speed ............................................................ 1700 RPM
Cooling system............................................ Forced Air (fan)
Starting system... Electric starter motor (kick-start back-up)
Transmission ................................................ Automatic CVT
Chassis
Tire size, front..................................................... 120/70 - 12
Tire size, rear...................................................... 130/70 - 12
Chassis material................................................... Aluminum
Front suspension.........................................Telescopic forks
Rear suspension .............................. Single shock absorber
Brake (front) ...........................................................Disc type
Brake (rear) .................................................Drum/shoe type
Electrical
Ignition type ..............................................................DC-CDI
Battery ..................................................................... 12v-6Ah
Headlight ........................................................... 12v 35/35W
Tail/brake light ..................................................... 12v 5/21W
Turn signal light ................................................12v 10W X 4
Position light ........................................ 12v5W (front & rear)
Main Fuse......................................................................... 7A
53
EXHAUST EMISSION CONTROL SYSTEM
KYMCO Clean-Air System
The KYMCO Clean-Air System is a secondary air suction system that helps the exhaust gases to burn more completely.
When the engine's exhaust is sent into the exhaust system, it contains some unused fuel. This exhaust is still hot
enough to burn the unused fuel. The Clean-Air system introduces more air so the oxygen will then permit the unused fuel
to burn in the exhaust system. This continued burning action uses up a great deal of the normally unused fuel and other
gases, as well as changing a significant portion of the poisonous carbon monoxide into harmless carbon dioxide. The
Clean-Air system does not use any energy from the engine and does not affect the scooter's performance.
1 Exhaust valve
2 Cylinder
3 Catalytic converter
4 Engine oil
5 Crankshaft
6 Fresh air
7 Carburetor
8 Intake manifold
9 Fresh air
AT Air injection air cleaner
AK Vacuum hose
AL Air injection control valve
AM Air
22
22
2
33
33
3
44
44
4
11
11
1
55
55
5
66
66
6
77
77
7
88
88
8
99
99
9
ATAT
ATAT
AT
AKAK
AKAK
AK
ALAL
ALAL
AL
AMAM
AMAM
AM
54
Crankcase Emission Control System
Your Agility scooter’s engine is equipped with a closed crankcase system. Blow-by gases are routed back in to the combus-
tion chamber via the intake system. This system does not allow the blow-by gases to enter the atmosphere.
Exhaust Emission Control System
The exhaust emissions from your scooter are controlled by engine design, factory-set fuel delivery, ignition settings, and
exhaust system design. This system also includes a catalyzer in the exhaust system.
Noise Exhaust Emission Control System
The engine, intake and exhaust systems of your scooter were designed to comply with federal, state and local noise level
requirements. Do not modify the engine, intake or exhaust components, as doing so will affect compliance with these noise
level requirements.
Please do not modify or change any KYMCO-designed components that may alter the sound or emission level from
your Agility scooter.
EMISSION CONTROL & WARRANTY INFORMATION
KYMCO LIMITED WARRANTY
NOISE EMISSIONS
KYMCO USA Inc, 5 Stan Perkins Road, Spartanburg, SC 29307, USA warrants that this vehicle was designed, manufac-
tured and equipped so that when new, it would conform with the applicable Motorcycle Noise Regulations of the U.S. EPA
Environmental Protection Agency.
This warranty is not limited to any particular part, component or system of the vehicle. Defects in design, assembly, or in any
part, component or system of the vehicle which, at the time of sale to the first purchaser, caused noise emission levels to
exceed applicable Federal standards in effect at the time of manufacture, are covered by this warranty.
55
KYMCO LIMITED WARRANTY
56
INDEX
Accessories & Modifications ..................................6
Air Filter Maintenance ..........................................37
Battery ........................................................... 38 - 39
Brake Fluid Level Inspection ................................43
Brake Inspection ........................................... 19 - 20
Brake Shoe & Pad Inspection ..............................44
Break-in Recommendations.................................16
CA Prop 65 Warning ............. (inside of front-cover)
Chassis Inspection ...............................................25
Cleaning Your Scooter.................................. 45 - 46
Clock......................................................................14
Electric Start Button.............................................. 11
Emission - KYMCO Clean Air System .................53
Emission Information & EPA Warranty ................54
Engine Oil Inspection ...........................................19
Engine Oil Level Inspection & Change........ 40 - 41
Engine Oil..............................................................40
Engine Stop Switch .............................................. 11
Forward ...................................................................2
Fuel Level / Filler Cap ..........................................22
Fuel System ..........................................................38
Fuse.......................................................................39
Headlight Dimmer Switch ..................................... 11
Helmet Posts.........................................................13
Horn & Lights Inspection ......................................24
ID Numbers Record .............. (inside of back-cover)
Ignition Switch & Steering Lock ..................... 9 - 10
Importance of Maintenance .................................33
Index ......................................................................56
Instrument Inspection ...........................................23
Instruments ...........................................................14
Keys.........................................................................9
KYMCO Limited Scooter Warranty ......................55
Left-hand Handlebar Switch......................... 11 - 12
Load Limits & Guidelines .......................................5
Locations of Parts & Controls .......................... 7 - 8
Main Stand ............................................................13
Maintenance Record .................................... 49 - 50
Maintenance Schedule ................................. 34 - 35
Manual Icon Legend ............. (inside of front-cover)
Parking Your Scooter .................................... 31 - 32
Passenger Foot Rest............................................15
Pre-ride Inspection ........................................ 18 -25
Riding Your Scooter ...................................... 28 - 31
Right-hand Handlebar Switch .............................. 11
Scooter Safety .................................................. 3 - 4
SECTION 1 - SAFETY ..................................... 2 - 6
SECTION 2 - CONTROLS & FEATURES..... 7 - 15
SECTION 3 - OPERATION .......................... 16 - 32
SECTION 4 - MAINTENANCE.....................
33 - 50
Spark Plug.............................................................43
Specifications (Agility 125) ...................................52
Specifications (Agility 50) .....................................51
Starting the Engine (electric start) ............... 26 - 27
Starting the Engine (kick start).............................27
Steering & Handlebar Inspection .........................23
Storage .......................................................... 47 - 48
Table of Contents....................................................1
Tire Break-in..........................................................17
Tire Inspection .............................................. 20 - 21
Tire Pressure.........................................................36
Tires.......................................................................36
Transmission Fluid Change .................................42
Turn Signal Switch ................................................12
Turn Signals ..........................................................12
Under-seat Storage Compartment ......................12
The ignition switch key identification code is stamped on tab 1 supplied with the key. If you require a replacement key, you will
need this code to obtain a new key from your authorized KYMCO dealer. Record the key number in the box above.
Record the Vehicle Identification Number 2 and Engine Serial Number 3 in the boxes above for future reference (to assist
you in ordering parts from your authorized KYMCO dealer or for reference in case the vehicle is stolen).
Identification Numbers Record
1. IGNITION SWITCH KEY IDENTIFICATION NUMBER
2. VEHICLE IDENTIFICATION NUMBER (VIN)
3. ENGINE SERIAL NUMBER (ESN)
NOTE: Your scooter’s keys may differ in appearance from those shown in this manual.
11
11
1
3
22
22
2
5 Stan Perkins Road
Spartanburg, SC 29307
Telephone: (888) 235-3417
FAX: (864) 327-4745
Prepared: February 2009
T300-KG10SA/KN25SA-US-A5
49

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kymco Agility 125 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kymco Agility 125 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info