457447
13
Verklein
Vergroot
Pagina terug
1/29
Pagina verder
13 Service Manual
For internal use only
4. Function tests
4.1 Safety precautions - microwave energy
Service technicians must never be exposed to the microwave radiation which can be
emitted by the magnetron or other components producing microwaves if the appliance
is not connected correctly or operated improperly.
All input and output connections, waveguides, flanges and seals are to be attached and
sealed correctly.
Never operate the appliance without having placed items in the cooking cavity which
absorb the microwaves.
Never look into the open waveguide or the antenna when the. magnetron is live.
The appliance must never be operated without the housing or with the door open.
If the fuse blows, always block the system operability first (all microswitches) before the
appliance is switched on again. If a microswitch is defective, always replace all micro-
switches.
Before activation of the magnetron or before repair work, check the following points with all
appliances:
The door does not close properly at the frame because it is deformed or the hinges are damaged.
Door or door seal damaged.
Appliance obviously damaged.
All defective or incorrectly set components in the locking, control, door locking, microwave generator and
transmission systems must be repaired, replaced or correctly set. Service technicians must first remove
their watches for all work on or near the magnetron.
Attention!
The high-voltage capacitor could still be electrically charged about 30 sec. after the appliance has
been switched off. It is advisable to discharge the capacitor each time through both poles using a
suitably insulated cable. Secondary power circuits of the transformer have a high voltage and a low
amperage and for this reason it is extremely dangerous to work near these components if the
appliance is plugged into the mains. Never touch cables with your bare hands or with non-insulated
tools when the appliance is in operation.
Do not measure the electric voltage of a high-voltage circuit or magnetron filament.
Make sure that the door is not loose or missing. If the screws are not properly tightened, this could
lead to the discharge of microwaves.
Before you switch on the appliance, check that all electric connections are tight.
Ensure with a reasonable procedure that no microwaves are emitted.
Do not insert any metal objects through the lamp gap or through any other gap as such objects could
act as an antenna and could result in the emission of microwaves.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Kuppersbusch-EMWG-1050

Zoeken resetten

  • EMWG 1030. 0E vr.01 Typ BH32GF2
    Geen microgolven : Geen opwarming
    Voor de rest werkt alles Gesteld op 23-10-2023 om 14:34

    Reageer op deze vraag Misbruik melden
  • Magnetron inbouw EMWG 1050 1E-G is tijdens het opwarmen volledig (stil) uitgevallen. Niets werkt, geen toetsen, geen scherm. Doet helemaal niets meer. Gesteld op 11-4-2021 om 15:09

    Reageer op deze vraag Misbruik melden
  • De magnetron doet het niet meer de aardlekschakelaar schakelt uit als we de stekker erin doen Gesteld op 17-1-2021 om 17:33

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kuppersbusch EMWG 1050 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kuppersbusch EMWG 1050 in de taal/talen: Engels als bijlage per email.

De handleiding is 1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Kuppersbusch EMWG 1050

Kuppersbusch EMWG 1050 Gebruiksaanwijzing - Nederlands - 29 pagina's

Kuppersbusch EMWG 1050 Gebruiksaanwijzing - Deutsch - 33 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info