508050
10
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
10 English 1500 KS
Cutting Angle Adjustment
The base 13 can be tilted up to 45° for bevel cuts.
First loosen the two clamp levers 8 on the angle
scales incline the base according to the scale and
then retighten the clamp levers 8.
There are markings for 0, 15, 30 and 45° on the rec-
tangular opening at the front of the base. These mark-
ings show where the middle of the cut line is for bevel
work (the middle position has changed due to the
base having been tilted).
Note: For mitre cuts, the cutting depth does not corre-
spond to the value indicated on the cutting depth
scale 19.
The base has been set in the factory so that it makes
an angle of exactly 90° with the blade in basic position
(zero mark on scale). If you discover a slight deviation,
it can be corrected by turning the two threaded
studs 20 slightly.
Parallel Guide
The parallel guide 11 makes possible exact cuts
along a workpiece edge or the cutting of parallel
strips.
Release star grip bolt 10, slide parallel stop 11 by the
required amount. Tighten up star grip bolt 10.
Check before putting into operation that the mains
voltage agrees with the voltage specified on the
nameplate of the machine.
Switching on and off
Switching on: Press the safety button 2.
Press the on-off switch 3 and hold depressed.
Note: The on-off switch 3 cannot be locked on.
Switching off: Release the on-off switch 3.
Before any work on the machine itself, pull the
mains plug!
Wear protective gloves.
The saw blades used must conform with the char-
acteristic data given in these operating instructions.
Press and hold down the pin for spindle lock 4 and if
necessary rotate the blade until the lock snaps into
place.
Removal:
Swing back and hold the swinging protective
guard 12. Unscrew the clamping screw 22 with the
Allen key 21.
Remove the clamping flange 23 and the saw blade.
Assembly:
Clean the motor spindle, saw blade and all clamping
parts to be mounted. Mount the clamping screw 22
with washer and the clamping flange 23. Tighten with
the Allen key 21.
Pay attention to the correct mounting position of
the mounting flange 24 and the clamping
flange 23.
Observe when assembling: The cutting direction of
the teeth (direction of arrow on the saw blade) and
the direction of rotation arrow on the protective
guard must agree.
The swing guard 12, which covers the blade, moving
back automatically when the blade is brought into the
work, at the same rate at which the saw is brought in.
When you reach the end of the cut, the swing guard
moves back by spring action to cover the blade again.
The eye shield 14 allows you to look directly at the cut
or layout line. It adjusts itself automatically to the
depth setting and prevents chips and sawdust from
flying out towards you. Even at the minimum depth cut
setting the blade is covered, thus minimizing the risk
of accidents.
7 Putting into Operation
8 Replacing the Saw Blade
9 Swing guard
10 Eye shield
21
22
23
24
1500 KS.book Seite 10 Montag, 15. April 2002 11:11 11
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kress 1500 KS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kress 1500 KS in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info