508068
19
Verklein
Vergroot
Pagina terug
1/184
Pagina verder
Operation English 19
1400HKS,1400DS-EN / 1106
EN
Swing guard
When the saw blade is applied to the work-
piece, the swing guard (11), which covers the
saw blade, moves back automatically at the
same speed at which the blade is applied.
When you reach the end of the cut, the swing
guard moves back under spring pressure to
cover the blade again.
Setting the cut depth
The cutting depth can be set up to 66 mm
(1400 HKS).
The cutting depth can be set up to 200 mm
(1400 DS).
By releasing the clamp lever (7) on the housing,
the base (14) can be pressed downwards and
thus moved in the direction of cutting depth "0."
The cutting depth can be read off on the indi-
cator (24) or reset according to the scale.
Sawing to layout lines
On the front edge of the circular saw base,
there is a marker (indentation) for right-angled
cuts (zero setting) corresponding to the saw
blade width. There are also marking tongues
for 0° and 45° bevel cuts. These enable simple
and precise operation.
The marking tongues in the base of the circular
saw (see drawing) also correspond to the cut
width of the saw blade.
Fitting the saw blade
Move the motor of the circular saw to its highest
position (min. cutting depth) – as described
under Setting the cutting depth – by releasing
the clamp lever (7) and then re-securing the
clamp lever (7).
Pull the swing guard (11) back and hold it in
end position.
Then fit the individual parts onto the drive
spindle of the saw in the following order:
1. Flange (20)
2. Saw blade (18)
3. Thrust washer (22)
4. Washer (21)
5. Socket-head cylinder bolt M8 x 18 (23)
Press and hold down the pin for spindle lock
(19), and if necessary, rotate the saw blade
until the lock snaps into place.
With the pin for spindle lock (19) pressed down,
tighten the socket-head cylinder bolt (23) with
the hex key (13).
To replace the saw blade, carry out the same
steps in reverse order. Fit the new blade as
described.
Fitting the riving knife
Leave the motor of the circular saw in the
same position (min. cutting depth) as was
required to fit the saw blade.
Attach the riving knife (12) using the socket-
head bolt (16) and the washer provided. At first,
only tighten the socket-head bolt (16) lightly.
Adjust the riving knife (12) so that the dis-
tance to the tips of the saw teeth and to the
lowest point of the saw blade is max. 5 mm
(see Figure). The distance to the toothed rim
of the saw blade must not exceed 5 mm.
-NOTE-
The cutting depth should always match the thick-
ness of the workpiece, i.e. the blade should only
protrude from the material by approx.the height of 1
saw tooth. This is important in order to prevent
accidents!
-NOTE-
When sawing along a layout line, please ensure
that you cut according to the left or right edge of
the indentation or marking tongue, depending on
whether you are sawing to the left or right of the
layout line.
Changing the tool
-NOTE-
When inserting the blade, make sure that the
direction of the arrow on the saw blade corre-
sponds to the direction of the arrow on the housing.
The bearing surfaces of the saw blade, flange and
washer must be clean.
-NOTE-
This kickback safety device must be fitted!
36727_a_BA_Handkreissäge_1400HKS.book Seite 19 Donnerstag, 20. Oktober 2011 9:25 09
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kress 1400 HKS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kress 1400 HKS in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 13,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info