508042
12
Verklein
Vergroot
Pagina terug
1/63
Pagina verder
12
English 133 MDX
Mechanical 2-speed selector
For battery equipment, the mechanical 2-speed selec-
tor permits optimal drilling torques of 0–1500 rpm in
2nd speed and with high transmission in 1st speed
(0–450 rpm) very high tractive power even with
screws of a large diameter. The switchover is per-
formed by moving the switch
3
until it stops in position
1 or 2.
Torque selection
The battery-driven rotary screwdriver is equipped with
a seven-stage mechanical torque selection. The start-
ing torque for a particular screw is set at the adjusting
ring
4
according to the scale.
The volume of the torque is dependent on various fac-
tors – type and hardness of the material to be proc-
essed, type and length of the screws to be used, but
in addition the demands made on the screw connec-
tion. The data contained in the following table should
be observed as a guideline:
Stage 1 = approx. 1 Nm:
screws Ø 3 mm
Stage 2 = approx. 2 Nm:
screws Ø 3.5 mm
Stage 3 = approx. 3 Nm:
screws Ø 4 mm
Stage 4 = approx. 4 Nm:
screws Ø 4.5 mm
Stage 5 = approx. 5 Nm:
screws Ø 5 mm
Stage 6 = approx. 6 Nm:
screws Ø 5.5 mm
Stage 7 = approx. 7 Nm:
screws Ø 6 mm
When the set torque is reached it is signalled acousti-
cally through the construction of the torque coupling.
The coupling disengages with a click.
Operation of the
Quick Clamping Drill Chuck
Rotational direction switch in the LOCK position
.
The fully automatic spindle locking makes possible
quick and easy changing of the tool in the drill chuck.
Opening: Turn the sleeve in the “AUF” direction.
Clamping: Open the chuck and insert the tool as far
as possible.
Firmly clamp the chuck by turning the
sleeve in the “ZU” direction.
For soft drill shafts, it may be necessary to retighten
after a short time.
Caution! For reasons of safety, take the bat-
tery out of the device for all installation and
removal operations!
Drilling
When drilling, set the torque ring to the
“drill”
symbol.
The torque coupling is deactivated. Maximum torque
is available for drilling.
When drilling steel, take care that no swarf
enters the ventilation slits of the housing, as
these are attracted by the permanently active
magnet of the motor and would remain on the
motor.
Screwing
Make sure that the bit and screw correspond in size
and shape.
It is advisable to use socket-head screws since their
self-centering action ensures safe work.
Or even better – TORX screws and the corresponding
bits. Optimal screwing is achieved when the screwing
device is fixed securely in the screw head.
Dismounting the Drill Chuck
Rotational direction switch in the LOCK position
.
Remove the left-hand threaded screw that secures
the drill chuck on the drill spindle against unscrewing
in left rotation. The drill chuck can then be loosened
by lightly striking a Allen key clamped in the drill chuck
and screwed off.
Remounting takes place in the reverse order.
Clean the flat surfaces on the drill chuck and spindle
before mounting. Screw on the drill chuck firmly and
secure with the safety screw.
Observe in addition that, when using a rim gear drill
chuck, the chuck key must not be attached to the
machine with chains, cords or similar means.
When drilling or screwdriving, secure the work
pieces against being rotated by the drill.
8 Practical Tips
133 MDX - GB Seite 12 Freitag, 24. März 2000 8:42 08
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kress 133 MDX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kress 133 MDX in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info