813988
42
Verklein
Vergroot
Pagina terug
1/206
Pagina verder
42
REPLACEMENT OF BATTERIES
Batteries in the receiver, remote control or the power supply module can overheat, spill or even cause
an explosion. Do not use batteries that have been exposed to the sun, moisture, heat or vibration.
Install only batteries of the same type and the same manufacturer. Do not install new batteries with
worn ones. The remote control is powered by two AAA batteries. The B6R-R8U receiver and the
G60-ZB90 power module are powered by four AA batteries 1.5V. The battery life in the case of the
remote control and the receiver is estimated at about 1 heating season. The device manufacturer re-
commends the use of alkaline batteries because of the lower risk associated with unsealing. It is also
permissible to use rechargeable batteries. When removing batteries, do not use tools that can cause
a short-circuit. Replacing batteries with conductive objects can permanently damage the electronic
components of the remote control and the receiver.
Replacement of the batteries in the remote control:
Remove the cover located on the rear of the remote control.
Gently remove the used batteries from the remote control.
Install new AAA batteries observing the polarity markings (+/-).
Replace the cover on the back wall of the remote
Replacing batteries in the receiver/power supply module:
Open the cabinet door panel.
Carefully remove the B6R-R8U receiver/G60-ZB90 power module.
Remove the cover.
Remove the used four AA batteries and install new, paying attention to the
polarity markings (+/-) on the receiver/power module.
Replace the cover on the cover receiver/supply module.
NOTE!!!
Replacing batteries in the receiver/power supply module can only be done on a cool replace
with the gas supply cut o.
NOTE!!!
Batteries are classied as hazardous chemical waste, so, after using them, they should not be
disposed of with other household waste.
MANUAL CONTROL
The user selecting the manual control option receives a device equipped with a GV32 controller. Ple-
ase read this manual before operating the control module. Proceeding contrary to the instructions
may result in damage to the gas control system or to the device itself, and may result in re, property
damage or health impairment.
USER MANUAL FOR THE MANUAL CONTROL MODULE
Firing the device should be carried out according to the instructions below. The GV32 gas control sys-
tem has been designed to completely eliminate the need for maintenance or any adjustments. The
knobs are non-removable. Removing the knobs will damage the device. Never attempt to open or
otherwise tamper with the valve or any of its components.
Starting the device:
1. Turn ON / OFF Knob A slightly counter clockwise towards the IGNITION position until it stops. Then
press and hold the knob for 5 seconds (the gas ows to the control burner only).
2. Continue to hold down the knob and at the same time turn it towards the PILOT position (this activa-
tes the piezo pilot of the control burner). Hold down the knob in this position for another 10 seconds
until the control burner ignites (if the pilot does not light up, repeat the procedure immediately
42

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kratki PATIO MINI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kratki PATIO MINI in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans, Pools, Fins als bijlage per email.

De handleiding is 4.06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info