Handleiding Kratki KDZ (pagina 15 van 136) (Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Zweeds)

813982

Verklein

Vergroot

Pagina terug

1/136

Pagina verder

ber requires about 8 m3 of air. In the room in which the replace insert is to be installed that draws air

from the room, there must be no exhaust devices or other appliances equipped with a hearth. In rooms

with mechanical ventilation or very tight window frames, an individual air supply to the combustion

chamber of the insert should be used. It is best to use a fresh air intake from the outside for this pur-

pose. In the case of cast iron inserts with an optional intake, the intake system should additionally be

equipped with a damper so that the room does not lose temperature when the replace is not in use.

The air intake supplying combustion air should be selected so that it cannot become clogged. Inserts

with sealed combustion chamber SERIES NB, MB, NADIA, VN, LUCY, ZIBI realize air intake through the

intake nozzle. Eective combustion is guaranteed only by connecting the air intake from the outside.

Lack of such connection may result in inecient combustion, dirtying of windows.

The replace must not be exposed to moisture. If the chimney insert is installed at the stage of con-

struction and nishing works, care should be taken to protect the replace from moisture associated

with the conduct of so-called wet works such as plaster, plasterboard. In this case, you should also pay

special attention to the fuel used, so that construction waste and other materials than recommended

are not burned in the replace, as this can result in overheating of the insert and numerous damages.

Construction of the replace insert housing

The cladding should be designed so that the replace insert is not permanently attached to it, with

the ability to be installed and removed without damaging it. The cladding should allow easy access

for inspection of the chimney connector, operation of the shaft or chimney draft regulator (if these

are installed). Non-ammable and insulating materials should be used for the construction, such as

aluminum-coated mineral wool, ceramic bers, glass ber-reinforced heat-resistant plates, aluminum

coatings. The distance of insulation from the walls of the replace insert should be 8 - 12 cm. The di-

stance between the frame of the replace and the casing must not be less than 5 mm (the expansion

joint does not require insulation). The cladding should provide access to the air needed for combu-

stion, as well as ventilation of the replace, through the use of appropriate grilles selected according to

the power of the device. At the bottom of the replace stove enclosure should be installed inlet grille

through which air is supplied to the housing (40-60 cm2 / 1 kW). To ensure proper discharge of hot air

from the hood, an air outlet grille must be installed in the hood. The minimum active area of the grilles

is selected depending on the power of the insert: from 50 to 70 cm2 per 1 kW.

A very high temperature is reached inside the housing, so a decompression shelf should be installed

in the housing at a distance of about 40 cm from the ceiling. It prevents heating of the ceiling in the

room, heat loss, and forces the installation of outlet grilles under it at the appropriate height that emit

heat from the chamber above the replace. Decompression grilles are installed on two sides of the

enclosure alternately, for example, alternately higher and lower above the decompression half. The

size of the grilles and their active area is not important.

Note

Due to the high temperature in the insert housing, the grilles in the hood as well as the crown of the

air distribution system in the house must be metal. In the replace hood, we only install grilles without

louvers.

OPERATION OF THE FIREPLACE INSERT

When cold, the replace insert should have all the dampers closed so that the room in which it is

installed does not lose temperature when the replace is not in use. Closed dampers will also prevent

the possibility of condensation on the lower parts of the insert, especially the sill, The appearance of

condensation can result in corrosion of steel components. Do not use an uncovered replace insert

except for test kindling. BASIA and MILA replace inserts must be equipped with a manual or auto-

matic ue gas damper mounted on their inlet. To purchase a compatible damper, contact the sales

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Kratki KDZ Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info