716903
12
Verklein
Vergroot
Pagina terug
1/29
Pagina verder
22 23
This means that the temperature increases far above the desired value or falls
far below the desired value. The innovative new percent mode now lets the user
specify the switching duration of the heater in percent using the "+" and "-" but-
tons (Pos. 3+4) (100% being the max. temperature) rather than setting the desired
temperature. Now the result of the setting must be checked by using the "Actual"
temperature display. If the desired temperature has not yet been reached, the
percentage must be increased.
By setting percentages of the heating duration, the temperature of the
high-pressure jet is kept constant in a very narrow range.
The last value set is also saved after the unit is switched off in percent mode.
Operating hour meter
The cleaner is equipped with an operating hour meter. If during normal opera-
tion the momentary operating mode button ( "°C" or "%" ) is actuated for more
then 2 seconds, the operating time of the pump is displayed for 5 seconds and
afterwards the combustion time for 5 seconds as well. Thereafter the display
shows the original values again. As long as the operating hours are displayed
no further inputs on the monitor are possible.
The operating time is displayed in hours [ h ] either in the “TARGET” or in
the „ACTUAL“ window. The 1000 and 100 hours are displayed in the „TARGET“
window and the 10, 1 and 1/10 hours in the “ACTUAL” window:
Pump operating time: Target-Display: P 9 9 Actual-Display: 9 9. 9 for 9 999,9h
Combustion time: Target-Display: F 9 9 Actual-Display: 9 9. 9 for 9 999,9h
e.g.: F00 27.3 = Cumbustion time 27 hours and 18 minutes
The thermostat has two operating modes:
1. Temperature mode
This mode is always activated when the unit is switched on or can be selected
using the "°C°" button (Pos. 5). The red LED above the "°C" button and next
to the set temperature display lights up.
The desired "Set" temperature is set using the two buttons (+/-, Pos. 3+4) and
can be read in the upper display (Pos. 1). If you press the button for a longer time,
the set temperature is quickly adjusted in 5 °C increments.
The last set value set is also stored after the unit is switched off and is available
again immediately after switching back on. The current spray temperature can
be read from the bottom display (Pos. 2)
2. Percentage mode
This mode is activated by pressing the "%" button (Pos. 6). The yellow LED above
the "%" button and next to the set temperature display flashes.
In the temperature control of high-pressure cleaners in temperature mode (“°C”),
the water temperature is measured at the outlet of the heater, and the heater
is switched on an off according to the temperature desired by the user.
Due to the large amount of water in the heating coil, it takes a long time
until the temperature sensor registers that the burner has switched on
and the desired temperature has been reached.
Thermostat
The thermostat controls the spray water tem-
perature. After you switch on the device, "888"
appears in both displays for approx. 1 second
as a test of the functioning of the displays.
Functional details Functional details
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kranzle e-therm 603 M 36 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kranzle e-therm 603 M 36 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Kranzle e-therm 603 M 36

Kranzle e-therm 603 M 36 Aanvulling / aanpassing - Deutsch - 25 pagina's

Kranzle e-therm 603 M 36 Gebruiksaanwijzing - Deutsch - 29 pagina's

Kranzle e-therm 603 M 36 Aanvulling / aanpassing - English - 25 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info