716915

Kranzle WS-RP 1000 TS Handleiding

18
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
www.kraenzle.com
High-pressure cleaner
WS 800 TS
|
WS 1000 TS
|
WS 1200 TS
WS-RP 1000 TS
|
WS-RP 1200 TS
WS-RP 1400 TS
|
WS-RP 1600 TS
WSC-RP 1000 TS
|
WSC-RP 1200 TS
WSC-RP 1400 TS
|
WSC-RP 1600 TS
Operating manual
EN
2 3
EN
Operating manual
High-pressure cleaner
WS 800 TS
|
WS 1000 TS
|
WS 1200 TS
WS-RP 1000 TS
|
WS-RP 1200 TS
WS-RP 1400 TS
|
WS-RP 1600 TS
WSC-RP 1000 TS
|
WSC-RP 1200 TS
WSC-RP 1400 TS
|
WSC-RP 1600 TS
Operating manual!
This manual is a translation of the original manual.
Read and conform safety
instructions before use! Technical data will be found in the Spare parts list.
Please be aware that the spare part list is part of the operating manual.
Keep both leaflets for later use or any subsequent owners.
4 5
Contents Explanatory symbols
Dear customer:
We would like to congratulate you on the purchase of your new high pressure
cleaner and thank you for your confidence in our products!
Your choice has fallen on an absolute quality product!
Kränzle high pressure cleaners are characterized by their convenient and compact
design as well as their high suitability for everyday use.
Highest precision and dimensional accuracy in addition to a technology package
consisting of a multitude of details mark the difference when it comes to
performance, safety and durability.
In order to facilitate handling of the high pressure cleaner, the following pages are
intended to further explain its use. The illustrations may be subject to deviation
depending on the type of equipment or accessory of high pressure cleaner
purchased by you.
Contents ........................................................................................... 4
Explanatory symbols ................................................................. 5
Safety notes ................................................................................... 6
Description of high pressure cleaner .................................. 10
General rules ................................................................................... 12
Functional details ......................................................................... 14
Putting into operation .............................................................. 19
Direct suction ................................................................................ 24
Taking out of operation ............................................................ 25
Small repairs - do it yourself ................................................... 2
Kränzle accessories .................................................................... 30
EU Declaration of Conformity ................................................ 32
Warranty ......................................................................................... 33
Inspection reports ....................................................................... 34
Explanatory symbols used in the operating manual
Failure to observe this note may entail
environmental damage.
Note on the use of the high pressure cleaner that failure
to adhere to the instructions may cause excessive wear
or total breakdown of the WS/WS-RP/WSC-RP-series.
Warning!
Failure to observe this note may result in serious injuries!
Explanatory symbols affixed to the high-pressure cleaner
In case of improper use, the high pressure jets can be
very dangerous. Do not direct high pressure jet at persons,
animals or active electrical equipment or the high-pressure
cleaner itself.
The high-pressure cleaner may not be connected directly
to the public drinking water supply network.
Risk of burns due to hot surfaces!
Products marked with this symbol may contain constituents
posing a risk to health or the environment if incorrectly
disposed of. These products must never be disposed of
as household waste.
Explanatory symbols affixed on the packaging
This symbol denotes recyclable packaging materials
which must not be disposed of as household waste.
Information on proper disposal will be gathered from
the recycling directives issued by your local authority.
6 7
Safety notes - This is prohibited!Safety notes
Replacement of the power supply cables is only permitted by use of an original
power supply cable of the manufacturer and must be performed by a qualified
electrician.
Safety devices serve to protect the user and must never be de-activated or their
function bypassed.
The high-pressure cleaner is to be properly used. The user is required to adhere
to local requirements and to watch out for the persons in the danger zone!
If used in elevated positions where there is a risk of the unit falling to the ground,
it must be secured against rolling away or tipping over.
The high-pressure cleaner is not designed for use by persons with restricted physical,
sensory or mental abilities (including children)!
User operating the high-pressure cleaner should wear the necessary protective
clothing, i.e. waterproof clothing, rubber boots, safety goggles, ear protection
headwear etc. It is prohibited to use the high-pressure cleaner in close vicinity
to people lacking suitable protective clothing.
Use of high-pressure cleaners may result in aerosols being generated. An aerosol
is a mixture of floating solid or liquid particles in a gas. Inhaling aerosol parti-
cles may cause damage to health. Employers are under obligation to carry out
a hazards assessment in order to determine the necessary protective measures
to prevent inhalation of aerosols as governed by the surface due to be cleaned
in each case. Respiratory masks, Class FFP 2 or higher, are suitable for protection
against aqueous aerosols.
Whenever the high-pressure cleaner is left unattended, the mains disconnect
switch must always be switched off.
Do not spray against matter containing asbestos or other hazardous substances!
Never spray flammable liquids or liquids containing solvents such as paint thinners,
petrol, oil or similar liquids! Explosion hazard due to spraying such materials!
Due to the high pressure jet, damage may occur on the objects to be cleaned,
e.g. car tires; therefore, a minimum distance of 30 cm is to be kept!
Prior to putting the high-pressure cleaners into operation, check its components
(High pressure hose, power supply cables, safety trigger gun) for any damage.
Replace defect or damaged components!
Only use high-pressure hoses, couplings and fittings recommended by Kränzle.
Only these accessories ensure safety of the equipment.
If use is made of an extension cable, this must be suitable for outdoor use. In
addition care needs to be taken to ensure that the cable is kept dry and that it is
situated above the ground. We recommend the use of a cable drum capable of
keeping the socket at least 60 mm above the ground.
Never allow children or untrained persons to
use the high pressure cleaner or to play with it!
Children must be kept under supervision to
prevent them from playing with the equipment.
When using high pressure water for cleaning,
make sure that there is a clearly noticeable recoil
effect on the lance. Therefore ensure a firm
footing (see technical data).
8 9
Safety notes - This is prohibited!Safety notes - This is prohibited!
Never direct the high pressure jet at power sockets
or any other electrical installations! Within the
working area, all live parts are to be protected
from both water jet and spray mist.
Apply the safety catch on the safety trigger gun
after each use in order to prevent
unintentional spraying!
Only use a power supply cable in perfect working
order! Do not damage or improperly repair the
power cable (tearing, squeezing, running over, ...).
Never pull the high pressure hose if it has formed
kinks or “nooses”! Never pull the high pressure
hose over sharp edges!
Never direct the high pressure jet at people or
animals! Never direct the high pressure jet at
yourself or other persons, not even to clean
clothing or shoes.
Never direct the high pressure jet at the high
pressure cleaner itself! The high pressure cleaner
may not be placed within reach of the high
pressure jet spray mist!
Always pay attention to the underbody lance
resting on the surface! Bear in mind when using
a curved or angled spraying lance that there is
a significant amount of torque in the recoil!
(The underbody lance is available as
optional accessory).
10 11
Description of high pressure cleaner Description of high pressure cleaner
Design:
The devices of the WS/WS-RP/WSC-RP-series are high-pressure cleaners
capable of being applied both standing on the floor or hanging on the wall.
Please see construction scheme for more details.
This is what you have purchased:
1. Kränzle high pressure cleaner
WS 800 TS
WS 1000 TS
WS 1200 TS
WS RP/WSC-RP-1000 TS
WS RP/WSC-RP-1200 TS
WS RP/WSC-RP-1400 TS
WS RP/WSC-RP-1600 TS
2. Trigger gun with safety catch,
short design with quick release
coupling
3. Stainless steel lance with flat jet
nozzle and quick release coupling
4. Operating manual
spare parts list
5. high pressure hose
6. Screws and holders for lances
(only applicable for wall moun-
ting - refer to chapter "Startup")
1. Handles
2. Pump head made of special
brass
3. Holder for lance (only applicable
in case of wall mounting)
4. Large stainless steel
pressure gauge
5. On/Off switch with motor
protection
6. Pedestals
7. Eyelets for wall mounting
8. Infinitely variable pressure
and quantity regulation
12 13
General rules General rules
Oil change
The first oil change should be carried out
after approximately 50 operating hours,
then every year or after 250 operating
hours. If the oil turns grey or white,
you must change the oil. In case of
exchanging oil being required, the oil
drain screw must be opened above a
container and the high pressure cleaner
be emptied. The oil is to be caught in the
reservoir and disposed of in an approved
manner.
New oil
WS: 1. l
WS-RP, WSC-RP: 0.8 l
Kränzle High Performance Gear Oil
(Item no.: 400932)
WS
Intended use
This high pressure cleaner is to be used solely for high pressure water jet cleaning
applications without detergents or low-pressure cleaning work with detergents
(e.g. with a foam injector or washing brush).
Environmental, refuse disposal and water protection regulations
must be observed!
Inspections
The high pressure cleaner must be inspected according to the “Guidelines for
Liquid Spray Devices” at least once every 12 months by a qualified person, to
ensure that continued safe operation is guaranteed. The results of the inspection
are to be recorded in writing (see Inspection reports).
High pressure cleaners used for commercial purposes have to be
checked by a qualified person at least every 12 months!
Accident prevention
The high pressure cleaner is designed for accidents to be impossible if used
correctly. The user is to be notified of the risk of injury from hot machine parts
and the high pressure jet. The “Guidelines for Liquid Spray Devices” must be
complied with.
Oil leakage
If oil leaks contact your nearest after-sales service (dealer) at once.
(environmental damage, damage to the transmission).
In case of increased humidity or fluctuations in temperature
development of condensed water is possible. If the oil turns grey
or white, you must change it.
WS-RP/
WSC-RP
14 15
Functional details Functional details
Please note: Lack of water
Lack of water occurs more often than you
probably believe. The more powerful a high
pressure cleaner is the greater is the danger
that a lack of water occurs. If there is only
an insufficient amount of water available,
cavitation (water-gas mixture) arises inside
the high pressure pump, which is normally
noticed too late or even not at all. The high
pressure pump will be destroyed. Please
check the available quantity of water by fil-
ling a bucket with liter scale for one minute.
Required minimum quantity of water (see technical data).
If the metered quantity of water is too small, you have to use a
different water connection, guaranteeing the necessary output.
Lack of water leads to an accelerated wear of the joints (no warranty).
Never let the high pressure pump run dry for more than 60 seconds.
Water supply
Please pay attention to the regulations of your waterworks company!
In accordance with DIN EN 61770, the high pressure cleaner may not
be directly connected to the public drinking water supply lines.
A brief connection however is permissible according to DVGW
(German Association for Gas and Water Affairs) if a non-return
valve with tube ventilator (Kränzle item no.: 410164) is built into the
water supply. Once the water has passed through the non-return
valve it is no longer considered as drinking water. Also indirect
connection to the public drinking water supply lines is permissible
by way of free emission in accordance with EN 61 770; e.g. by using
a reservoir with a float valve. Direct connection to a non-drinking
water supply line is permissible.
Insufficient quantity of electricity
If there are too many collectors in your
proximity connected to the network at the
same time, the available voltage and the
current intensity may decline. Consequently
the motor of the high pressure cleaner does
not start or even blows. The power supply
may also be insufficient if the power supply
cable is too long or too thin. If extension
cables are too long, this may lead to a
voltage drop causing malfunctions or
start-up difficulties.
Check the line fusing and have the voltage and the available current
intensity checked by an expert in case of uncertainty (see technical data).
Electrical connection
The high pressure cleaner is supplied with a 5 meters long power supply cable.
The mains plug must be fitted to a standard grounded socket with a 30 mA
residual current operated device. Connection up to the mains must be carried
out by a properly trained electrician and must comply with the requirements
of IEC60364-1. The socket must be protected with a 16 A (WS-RP and WSC-RP
with a 32 A delay action) fuse on the mains side. When using an extension cable,
this must have an earthed lead which is properly connected to the socket. The
conductors in the extension cable must have a minimum cross section of 1.5 mm².
Plug connections must be of a spray-proof design, and may not be located on
a wet floor. For extension cables of more than 10 m in length, the minimum
cross-section must be 2.5 mm²! When using a cable drum, the power supply
cable always must be unwound all the way.
16 17
Pressure control valve/safety valve
The pressure control valve/safety valve protects the high pressure cleaner from
a build up of excess pressure, and is designed not to permit an excess pressure
to be selected for operation. The limit nut on the handle is sealed with a spray
coating. The operating pressure and spray rate can be steplessly adjusted by
turning the handle.
Replacements, repairs, new adjustments and sealing should only
be performed by qualified persons.
Motor protection switch
Motor is protected against overload by means of a motor protection switch.
In case of motor overload or blocking, the motor of the high pressure cleaner
switches off automatically. If motor tends to switch off repeatedly, make sure
to detect appears. Make sure to detect and remedy the cause of the failure.
Replacements and inspection work should only be performed by qualified
persons when the high pressure cleaner is disconnected from the power
supply, i.e. with plug pulled out from the electrical socket.
Total stop system with delayed motor cut-off
When opening the trigger gun the motor is started via a total-stop system.
When
closing the trigger gun the motor is switched off only after 38 seconds and the device
is in standby mode. The delayed switch-off is necessary because switching on and off
motors frequently on high-pressure cleaners of this size may involve heavy load on the
power network and cause increased wear of internal electrical parts. After 20 minutes
in standby, the device will disconnect from the mains and must be turned on again
by the main switch. The machine restarts automatically when the gun is re-opened,
provided that the master switch is on.
Water and cleaning system
Water must be supplied to the high pressure pump under pressure or directly sucked
in out of a pressureless container. The water is then forced under pressure by the
high pressure pump to the lance. The high pressure jet is formed by the nozzle at
the end of the lance.
Environmental, refuse disposal and water protection regulations
must be observed!
Safety jet pipe with safety trigger gun
The high pressure cleaner can only be operated when the trigger of the safety
deactivation trigger gun‘s trigger is actuated. When the trigger is pulled, the
safety trigger gun opens. The liquid is then transported to the nozzle. The spray
pressure increases and quickly reaches the operating pressure. When the trigger is
released, the safety trigger gun closes and any further spraying of liquid from the
safety jet pipe is prevented. The stainless steel pressure gauge must show 0 bar.
The increase in pressure when the safety trigger gun is closed causes the pressure
control valve-safety valve to open. The motor is switched off by the pressure
switch. When thesafety trigger gun is opened, the pressure control valve - safety
valve closes, the motor is started and the high pressure pump resumes pressure
spraying from the safety jet pipe with the selected operating pressure.
The safety trigger gun is a safety device. Repairs should only be perfor-
med by qualified persons. Should replacement parts be required, use
only components authorized by the manufacturer.
Functional details Functional details
18 19
Wall mounting shall be performed by a specialist.
For mounting, please do not just observe the carrying capacity of the
wall but also the weight of the high-pressure cleaner (please refer to
technical data).
Putting into operation
Safety shutdown
If the high-pressure cleaner is accidentally not turned o after use or the safety
trigger gun is not used for 20 minutes, the high-pressure cleaner automatically
changes into safety state by deactivation. By operating the main switch once
more, the high-pressure cleaner is activated again.
High pressure hose and spray device
The high-pressure hose and spray device which are part of the WS/WS-RP/
WSC-RP-series equipment, are made of high-quality material and engineered
to conform with the operating conditions of the high-pressure cleaner and
are duly labelled.
If replacement parts are required, only such parts that are authorized
by the manufacturer may be used. The warranty is automatically void
if spare parts of third-party providers are used! The high pressure hose
and spray device must be connected in a pressure-tight manner
(without leakage).
The high pressure hose may not be driven over, pulled excessively, or
twisted. The high pressure hose may under no circumstances be pulled
over sharp edges. Defective high pressure hoses must not be repaired
(acc. to DIN 20022) but have to be replaced by new hoses approved by
the manufacturer.
Prior to putting the high pressure cleaner into operation make sure
that all safety instructions be observed.
The WS/WS-RP/WSC-RP-series may be applied both as a standing device as well
as mounted on the wall. When setting down the high-pressure cleaner please
provide for a safe stand.
Wall mounting
Attach the holder for the lances with
a screwdriver and the enclosed screws.
The high-pressure cleaner may be carried
by two persons. Please note the weight of
the high-pressure cleaner (refer to technical
data).
When setting down the high-pressure
cleaner please provide for a safe stand.
Please find the eyelets for wall mounting
on the back of the device.
Hole spacing distance (bore): 485 mm
Functional details
20 21
Putting into operationPutting into operation
2. Plug screw high-pressure hose included
in scope of delivery at pump outlet and
tightly screw pressure-tight.
1. Unwind high pressure hose straight
and without nooses. (When using high
pressure hose extensions take care
that the max. length of 20 m is not
exceeded!)
The high pressure hose may leave signs
of abrasion on some floors. Alternatively,
please also find non-marking high
pressure hoses in our range.
5. After insertion of the lance, release
retaining sleeve and make sure that
the lance is in a secure position.
Grease quick release nipple regularly
using acid-free grease.
4. First pull back the retaining sleeve
of the safety trigger gun, then insert
lance into the plug coupling sconnection
of the safety trigger gun.
3. Tightly screw together high pressure
hose and safety trigger gun.
Prior to insertion, check plug coupling connection of lance for
cleanliness (sand, dirt ..) and use clear water to clean, if necessary.
Impurities may damage the sealing in the plug coupling.
Accessories may only be connected to a Kränzle-approved trigger gun
with safety catch.
Neither set up or operate the WS/WS-RP/WSC-RP-series in rooms
where there is a risk
of fire or explosion nor put it into puddles.
Do not use the high pressure cleaner under water. If, none the less,
the high pressure cleaner
is operated in a hazardous area,
the applicable safety regulations are to be observed.
22 23
14. Switch on high pressure cleaner with
opened safety trigger gun. Bleeding
of the high pressure cleaner: Pull and
release trigger of safety trigger gun
several times. Start cleaning task.
13. Connect to circuit (see technical data).
Do not touch the mains plug or any live parts with wet or moist hands.
15. When using the turbokiller lance
(optional) make sure that lance points
downward when starting.
Putting into operation
16. Adjust operating pressureinfinitely
using the rotary handle. The maximum
pressure is factory-set.
Putting into operation
It is imperative that safety instructions be observed during
use of the high pressure cleaner.
WS
10. If using a water inlet filter check it
for cleanliness prior to each startup.
Manually unscrew filter bowl, remove
sieve and thoroughly rinse and clean
with the rest of the parts in clear
water. If the sieve is dirty, water can
not get through and pressure will
not build up.
11. Connect water hose to water inlet (mi-
nimum requirements;
5 m hose length,
cross-section ¾", 10 bar). The high pressure
cleaner may be connected to a water
mains (1-10 bar pre-pressure) with eit-
her cold or hot water (up to 60 °C).
The WS/WS-RP/WSC-RP-series provides
the opportunity of sucking in water out
of a container (see direct suction).
Check the water inlet sieve for damage. Do not operate the
high pressure cleaner without or with a damaged filter.
Be careful when using hot water!
When running your high pressure cleaner with hot water of 60 °C raised
temperatures occur. Do not touch the metal parts of the high pressure
cleaner without safety gloves!
12. The oil level must reach to the upper
edge of the mark.
WS-RP/
WSC-RP
24 25
Direct suction Taking out of operation
1. Switch off the high pressure cleaner
2. Cut off the water supply
3. Open the safety trigger gun catch briefly until the pressure is released
4. Apply safety catch on the trigger gun
5. Remove high pressure hose and safety trigger gun
6. Emptying high pressure pump: Hold high pressure hose and switch
motor on until water jet stops escaping at the outlet.
7. Pull the plug from the socket
8. Clean high pressure hose and wind up without loops
9. Clean and wind up the power supply cable
10. Clean the water inlet sieve
11. Store high pressure cleaners in frost-free rooms in winter
Direct water extraction
Due to the suction capacity of its high pressure pump (up to 2.5 m suction height,
max. hose length 3 m) this high pressure cleaner can suck in water for cleaning
purposes from separate containers or ponds.
2. Put filled suction hose into the water-
filled container and start the cleaning
job.
Use clean water only! Never suck in
water containing chlorine! Do not
suction air!
1. Mount suction hose with suction
filter (Item.-no.: 15033).
Prior to starting the first suction the high-pressure pump and the
suction hose has to be filled with water!
Note
Depending on the water quality it may occur after a prolonged standstill
that the valves get sticky. Consequently the high-pressure cleaner cannot
properly suck in water from a container. In this case connect a hose with
pressurized water to the pump inlet. Having started the high-pressure
cleaner the pressurized water opens the valves and the machine resumes
sucking in water from the container. Now you can carry on with your
cleaning task as usual.
Frost protection
For protecting the high-pressure cleaner against frost please empty it completely.
Separate high-pressure cleaner from water supply and switch it on.
By opening
the trigger gun the high-pressure pump presses water out of the high-pressure
cleaner. However, do not allow the device to operate without water for more
than one minute.
26 27
Small repairs - do it yourself Small repairs - do it yourself
WS
WS
The stainless steel pressure gauge shows
full pressure, but from the nozzle comes
only little water or no water at all.
(Inside the stainless steel pressure gauge is
no water but a filling with glycerin to damp
the vibration of the pointer.)
Proceeding:
Switch off the high pressure cleaner. Pull
plug from the socket. Operate safety trigger
gun catch several times to decrease the
pressure.
Unscrew safety trigger gun and lance first,
then rinse high pressure hose to remove
possible soiling.
Check water inlet filter for soiling.
If the problem still exists, take wire (paper
clip) and push through nozzle opening.
If this procedure is not successful, the
nozzle has to be replaced.
Problem
No water from nozzle although the high pressure cleaner is running.
The stainless steel pressure gauge shows full pressure.
Cause
Most likely the nozzle is blocked.
Pull plug from socket prior to starting any repair work!
The stainless steel pressure gauge shows
low pressure despite fully turned up pres-
sure regulation. The water from the lance
comes in squirts. The high pressure hose
vibrates. (Inside the stainless steel pressure
gauge is no water but a filling with glycerin
to damp the vibration of the pointer.)
Proceeding:
Unscrew all 6 valves, one after the other
(hexagonal brass screws, 3 in a row,
vertically and horizontally)
Take out valve body and O-ring by means
of needle nose pliers. Check O-ring for
damage. In case of a damage the O-ring
has to be replaced.
Take a wire (paper clip) and clean valves
under running water.
Do not forget the O-ring during reassembly!
Problem
Irregular jet from nozzle.
The stainless steel pressure gauge shows low pressure.
Cause
Most likely the valves are soiled or sticky.
WS-RP/
WSC-RP
WS-RP/
WSC-RP
28 29
Small repairs - do it yourselfSmall repairs - do it yourself
WS
WS
Having closed the trigger gun with safe-
ty catch, the high pressure cleaner must
shut down and the stainless steel pressure
gauge must show „0“ bar. If not shut down
and the stainless steel pressure gauge con-
tinuously shows full pressure, this could be
due to leakage at the high pressure pump,
at the pressure switch, at the high pressure
hose or at the trigger gun with safety catch.
In case of a leakage there is no guarantee for possible
consequential damages.
Problem
After closing the safety trigger gun the high pressure cleaner
keeps switching on and off.
The stainless steel pressure gauge continuously displays full pressure.
Possible cause No. 1
Leckage.
Proceeding:
Check connections from the high pressure
cleaner to the high pressure hose and from
the high pressure hose to the safety trigger
gun and also the connection between lance
and safety trigger gun for tightness.
Switch off the high pressure cleaner.
Shortly press the trigger of the safety
trigger gun to decrease the high pressure
cleaner. Unscrew high pressure hose,
safety trigger gun and lance and check
the O-rings. If the O-rings are damaged
they have to be replaced.
Proceeding:
Switch off the high pressure cleaner and
pull plug from socket. Stop water supply.
Operate safety trigger gun catch several
times to decrease the pressure.
Unscrew pump outlet.
There is no guarantee if the high pressure pump is damaged by
defective O-rings due to air induction or lack of water (cavitation).
Remove check body and check O-Ring
for soiling or damage. Also check seal
seat inside pump housing for soiling
or damage.
If sealing rings are defective replace
O-rings at once.
Problem
After closing the safety trigger gun the high pressure cleaner
keeps switching on and off.
The stainless steel pressure gauge continuously displays full pressure.
Possible cause No. 2
The non-return valve is defective.
WS-RP/
WSC-RP
WS-RP/
WSC-RP
30 31
Kränzle accessories Kränzle accessories
Item no.: 41075
Item no.: 15033
∅ 300 mm Item no.: 41105
∅ 420 mm Item no.: 41106
∅ 520 mm Item no.: 41107
Item no.: 12440 (fig. left)
Item no.: 12441 (fig. right)
Item no.: 410501
Floor washer Round Cleaner
(stainless steel)
*
From stainless steel
Various executions
Nozzle system 055
Suction hose
with suction filter
With return valve
Hose length 3 m
Adapter for accessories
with screw connections
With quick release nipple
For item no.: 12440 (fig. left)
400 mm extension
With grip plates
* in combination with adapter only
Rotating washing brush
*
400 mm
Stainless steel extension
Brush head ∅ 180 mm
Nozzle size 3.2 mm
Underbody lance
*
Stainless steel pipe
1000 mm extension
Nozzle system 4007
Please indicate the technical data of the high pressure cleaner
(device type) when placing your order.
The high pressure cleaner accessories are safety components!
Any warranty will be void if parts not authorised by Kränzle are used.
* in combination with adapter only
* in combination with adapter only
32 33
WarrantyEU Declaration of Conformity
We here by declare that the design of
the high pressure cleaner:
Nominal flow:
technical specifications
available from:
comply with the following guidelines
and their amendments for high
pressure cleaners:
Noise pressure level, typical:
Noise pressure level, guaranteed:
Applied conformity assessment
procedure:
Applied specifications and standards:
WS 800 - 1200 TS
WS-RP 1000-1600 TS
WSC-RP 1000-1600 TS
WS 800 TS: 798 l/h
WS 1000 TS: 960 l/h
WS 1200 TS: 1140 l/h
WS-RP/WSC-RP 1000 TS: 1000 l/h
WS-RP/WSC-RP 1200 TS: 1200 l/h
WS-RP/WSC-RP 1400 TS: 1400 l/h
WS-RP/WSC-RP 1600 TS: 1600 l/h
Fa. Josef Kränzle GmbH & Co. KG
Manfred Bauer
Rudolf-Diesel-Str. 20, 89257 Illertissen
Machinery Directive 2006/42/EC
EMC Directive 2014/30/EU
ROHS Directive 2011/65/EU
Outdoor Directive 2000/14/EC
8 dB (A)
91 dB (A)
Annex V, Outdoor Directive
2000/14/EC
EN 60335–1:2012/A13:2017
EN 60335–2–79:2012
EN 62233: 2008
EN 55014–1: 2006+A1: 2009+A2: 2011
EN 55014–2: 2015
EN 61000–3–2: 2014
EN 61000–3–3: 2013
Ludwig Kränzle
(Managing director)
Josef Kränzle GmbH & Co. KG
Rudolf-Diesel-Straße 20
89257 Illertissen (Germany)
Illertissen, 2019-04-05
The warranty obligation of Josef Kränzle GmbH & Co. KG towards the dealer
from whom you have purchased this Kränzle high-pressure cleaner (= product)
applies to material faults only such as material and manufacturing defects.
Defects attributable to long and frequent use of the product, typically arising
due to the age of the high-pressure cleaner and intensity of its use are defined
as normal wear in respect of product components. Purchaser’s rights to assert
claims for such defects are ruled out. Parts subject to wear include in particular
the pressure gauge, nozzle, valves, sleeves, high-pressure hose and spray equipment.
The product is to be operated in conformity with this operating manual.
The operating manual is deemed to be part of the warranty provisions.
Any changes made to the safety devices of the product or instances of
maloperation – such as exceeding the temperature and speed limits,
undervoltage, insufficient water supply and sewage water, or failure to
use the product for the intended purpose – may result in damage occurring
to the product. Such damage is not deemed to constitute any material defect.
Should the use of accessories or spares other than original Kränzle component parts
und original Kränzle replacement parts be the cause of defects on our product,
this may lead to all warranty claims becoming null and void. Only the use of
original Kränzle replacement parts matching the relevant Kränzle high-pressure
cleaner provides adequate assurance for safe and trouble-free operation of the
Kränzle high-pressure cleaner.
With regard to legal warranty claims, the limitation periods of the respective
countries shall apply.
Where warranty claims apply to any other defects, please contact your
local dealer, presenting the accessories together with your purchase receipt,
or the nearest authorised service centre. This can also be found on the
internet under
www.kraenzle.com.
34 35
Inspection reports Inspection reports
Owner: .................................................................................
Address: ...............................................................................
.....................................................................................................
Type: .......................................................................................
Serial no.: .............................................................................
Repair order no.: .............................................................
Inspection result (check)
The high pressure cleaner was checked by an expert according to the Guidelines
for Liquid Spray Equipment, the defects found have been rectified so that the
Labour Safety can be confirmed.
The high pressure cleaner was checked by an expert according to the Guidelines
for Liquid Spray Equipment. The Labour Safety cannot be confirmed unless the
defects found are rectified by repair or replacement of the faulty parts.
Scope of inspection o.k. yes no repaired
Type plate (on hand)
Operating manual (on hand)
Protective covering, Protective device
Pressure line (tightness)
Stainless steel pressure gauge (function)
Float valve (tightness)
Spraying device (marking)
High pressure hose / connector (damage, marking)
Safety valve opens at 10 % / 20 % exceeding
power supply cable (damage)
Protective conductor (connected)
On / O switch
Used chemicals
Allowed chemicals
Inspection data determined value set value
High pressure nozzle
Operating pressure ………………bar
Switch o pressure ……………..bar
protective conductor resistance not exceeded / value
Insulation
Leakage current
Safety trigger gun locked
The next retest according to the Guidelines for Liquid Spray Equipment has to be
carried out by: Month
................................................................... Year .......................................................................
Place, Date .......................................................................... Signature ...............................................................................
High pressure cleaners for industrial use have to be checked by an expert every
12 months! Inspection report on annually carried out Labour Safety Inspection (UVV)
according to the Guidelines for Liquid Spray Equipment. (This inspection sheet serves
as proof for the completion of the retest and must be kept carefully!)
Kränzle-test seals: Item no.: UVV200106
Owner: .................................................................................
Address: ...............................................................................
.....................................................................................................
Type: .......................................................................................
Serial no.: .............................................................................
Repair order no.: .............................................................
Inspection result (check)
The high pressure cleaner was checked by an expert according to the Guidelines
for Liquid Spray Equipment, the defects found have been rectified so that the
Labour Safety can be confirmed.
The high pressure cleaner was checked by an expert according to the Guidelines
for Liquid Spray Equipment. The Labour Safety cannot be confirmed unless the
defects found are rectified by repair or replacement of the faulty parts.
Scope of inspection o.k. yes no repaired
Type plate (on hand)
Operating manual (on hand)
Protective covering, Protective device
Pressure line (tightness)
Stainless steel pressure gauge (function)
Float valve (tightness)
Spraying device (marking)
High pressure hose / connector (damage, marking)
Safety valve opens at 10 % / 20 % exceeding
power supply cable (damage)
Protective conductor (connected)
On / O switch
Used chemicals
Allowed chemicals
Inspection data determined value set value
High pressure nozzle
Operating pressure ………………bar
Switch o pressure ……………..bar
protective conductor resistance not exceeded / value
Insulation
Leakage current
Safety trigger gun locked
The next retest according to the Guidelines for Liquid Spray Equipment has to be
carried out by: Month
................................................................... Year .......................................................................
Place, Date .......................................................................... Signature ...............................................................................
High pressure cleaners for industrial use have to be checked by an expert every
12 months! Inspection report on annually carried out Labour Safety Inspection (UVV)
according to the Guidelines for Liquid Spray Equipment. (This inspection sheet serves
as proof for the completion of the retest and must be kept carefully!)
Kränzle-test seals: Item no.: UVV200106
www.kraenzle.com
Josef Kränzle GmbH & Co. KG
Rudolf-Diesel-Straße 20
89257 Illertissen (Germany)
sales
@
kraenzle.com
Made
in
Germany
© Kränzle 21.01.2020 / Ord. no.: 302520 / Subject to technical modifications and errors.
… 18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kranzle WS-RP 1000 TS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kranzle WS-RP 1000 TS in de taal/talen: Engels als bijlage per email.

De handleiding is 6,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Kranzle WS-RP 1000 TS

Kranzle WS-RP 1000 TS Gebruiksaanwijzing - Nederlands - 19 pagina's

Kranzle WS-RP 1000 TS Aanvulling / aanpassing - Deutsch - 17 pagina's

Kranzle WS-RP 1000 TS Gebruiksaanwijzing - Deutsch - 19 pagina's

Kranzle WS-RP 1000 TS Aanvulling / aanpassing - English - 17 pagina's

Kranzle WS-RP 1000 TS Gebruiksaanwijzing - Français - 19 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info