716943
18
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
www.kraenzle.com
Kränzle 2017
Kränzle 2017 T
Kränzle 2020
Kränzle 2020 T
Operating manual
H i g h - p r e s s u r e c l e a n e r s
Read and conform safety instructions before use!
Keep instructions in a safe place for later use and
pass them on to any future user.
- USA -
Description
Kränzle 2017, 2017 T,
Kränzle 2020, 2020 T,
2
Ergonomically shaped handle
Cable reel with 5 m cable
Receptacle for gun with spray
lance (during breaks)
Generously dimensioned hose
drum with 15 m steel braided high-
pressure hose
(only available for T-models)
Hand crank (only available for T-models)
Ergonomically shaped handle
High-pressure gun
Large stainless steel manometer
Fully adjustable pressure control
Detergent hose
with filter
Interchangeable lance with Dirtkiller nozzle
Interchangeable washing lance
On/Off switch with signal lamp and motor
protection
Receptacle for high-pressure gun
Receptacle for Dirtkiller and lance
Generously dimensioned trolley
suited for difficult terrain and stairs
Description .......................................................................................... 2
Contents .......................................................................................... 3
Technical data ........................................................................................ 4
Overview This is what you have purchased ........................................... 6
General rules ......................................................................................... 7
Safety precautions accident prevention ................................................ 8
Extremely important: Water connection electrical connection ............. 10
Kränzle- technology
................................................................................. 12
Water and cleaning system ................................................ 12
Lance and spray gun ......................................................... 12
Pressure control valve safety valve ................................. 12
Motor protecting switch ..................................................... 13
High pressure hose and spray device ....................................... 13
Putting into operation ........................................................................ 14
Connection to water mains ................................................ 14
Direct suction ................................................................... 17
When using detergents ..................................................... 18
To shut down the pump / frost protection ............................................... 19
Small repairs do it yourself! ............................................................... 20
Inspections inspection reports ............................................................ 24
EG Declaration of Conformity ............................................................ 26
Guarantee ........................................................................................ 27
Accessories for high-pressure cleaners ................................................. 28
Spare parts list ................................................................................... 30
Complete assembly ........................................................... 30
Valve housing ................................................................... 32
Unloader valve and pressure switch .................................. 34
Motor ................................................................................ 36
Transmission .................................................................... 38
Gun with lance .................................................................. 39
Hose drum ........................................................................ 40
Dirtkiller with lance ........................................................... 42
Wiring diagrams ................................................................................... 43
Contents
Page
3
4
Operating press. fully adjustable
140 - 1600 psi 140 - 1600 bar
10 - 110 bar 10 - 110 bar
Nozzle size 25030 25030
Permissible overpressure 1800 psi / 125 bar 1800 psi / 125 bar
Water output
at 1,700 r.p.m. 6,8 l/min, 1,7 Gpm
at 1,700 r.p.m. 6,8 l/min, 1,7 Gpm
Water inlet temperature max. 140 °F / 60 °C max. 140 °F / 60 °C
Suction height 2.5 m 2.5 m
Hose drum no yes
Steel braided high-pressure hose
10 m 15 m
Detergent suction yes yes
Connected load
115 V ; 60 Hz ; 15 Amp 115 V ; 60 Hz ; 15 Amp
Power input P 1 - 1,6 kW P 1 - 1,6 kW
Power output P 2 - 1,5 HP P 2 - 1,5 HP
Weight 37 kg 39.5 kg
Dim. incl. pulling handle in mm 900 x 375 x 360 900 x 375 x 360
Sound level acc. to DIN 45 635 78 dB (A) 78 dB (A)
Sound level with Dirtkiller
82 dB (A) 82 dB (A)
Acoustic power L
WA
89 dB (A) 89 dB (A)
Recoil at lance approx. 20 N approx. 20 N
Vibration at lance
2.0 m/s
2
2.0 m/s
2
Kränzle Kränzle
2017 2017 T
Technical data
Permissible tolerance for figures ± 5 % acc. to VDMA uniform sheet 24411
5
Permissible tolerance for figures ± 5 % acc. to VDMA uniform sheet 24411
Operating press. fully adjustable
140 - 2000 psi 140 - 2000 bar
10 - 135 bar 10 - 135 bar
Nozzle size 25030 25030
Permissible overpressure 2200 psi / 155 bar 2200 psi / 155 bar
Water output
at 1,700 r.p.m. 7,5 l/min, 1,9 Gpm
at 1,700 r.p.m. 7,5 l/min, 1,9 Gpm
Water inlet temperature max. 140 °F / 60 °C max. 140 °F / 60 °C
Suction height 2.5 m 2.5 m
Hose drum no yes
Steel braided high-pressure hose
10 m 15 m
Detergent suction yes yes
Connected load
115 V ; 60 Hz ; 20 Amp 115 V ; 60 Hz ; 20 Amp
Power input P 1 - 2,3 kW P 1 - 2,3 kW
Power output P 2 - 2,0 HP P 2 - 2,0 HP
Weight 37 kg 39.5 kg
Dim. incl. pulling handle in mm 900 x 375 x 360 900 x 375 x 360
Sound level acc. to DIN 45 635 78 dB (A) 78 dB (A)
Sound level with Dirtkiller
82 dB (A) 82 dB (A)
Acoustic power L
WA
91 dB (A) 91 dB (A)
Recoil at lance approx. 22 N approx. 22 N
Vibration at lance
2.0 m/s
2
2.0 m/s
2
Kränzle Kränzle
2020 2020 T
6
3.
Dirtkiller lance with stainless steel pipe
This is what you have purchased
1. Kränzle high-pressure cleaners
2017 T, 2020 T with 15 m steel braided
high-pressure hose and hose drum NW 6
or
2.
Trigger gun with safety catch, insulated
handle and screw connection
4.
Vario-Jet lance with stainless steel pipe
5
. Handle with fixing screw for hose drum
6.
Operating manual
Kränzle high-pressure cleaners 2017, 2020
with 10 m steel braided high-pressure hose
but without hose drum NW 6
7
General rules
Range of application
Use machines for cleaning tasks with high-pressure water jet and detergents or with
high-pressure water jet without detergents only.
Inspections
The machine must be inspected according to the “Guidelines for Liquid Spray Devices”
at least once every 12 months by a qualified person, to ensure that continued safe
operation is guaranteed. The results of the inspection are to be recorded in writing.
This may be done in any form. For inspection reports see pages 24 - 25.
High-pressure cleaners used for commercial purposes have to
be checked by a qualified person at least every 12 months!
Accident prevention
The machine is designed for accidents to be impossible if used correctly.The operator is
to be notified of the risk of injury from hot machine parts and the high pressure water jet.
The “Guidelines for Liquid Spray Devices” must be complied with. (see pages 8 and 9).
Oil change:
The first oil change should be carried out after approximately 50 operating hours,
then every year or after 1000 operating hours. If the oil turns grey or white, you must
change the oil of your high pressure pump in any case.
Put the machine into a horizontal position, then open the oil discharge screw at the
bottom of the device over a collection reservoir. The oil is to be caught in the reservoir
and disposed of in an approved manner.
New oil: 0,35 l - Motor oil W 15/40.
Oil leakage: If oil leaks contact your nearest after-sales
service (dealer) at once. (Ecological damage, damage to
the transmission)
In case of increased humidity or fluctuations in
temperature development of condensed water is
possible; if the oil turns grey, you must change it.
8
Safety precautions
Bear in mind that during cleaning tasks
with a high-pressure water jet a significant
recoil at the lance arises (see technical
data on page 4).
Apply the safety catch on the trigger
gun after each use, in order to prevent
unintentional spraying!
Always aim the underbody lance! Bear
in mind when using a curved or angled
spraying lance that there is a significant
amount of torque in the recoil!
9
Safety precautions
- That`s forbidden!
Never allow children to use the
high pressure cleaner!
Never direct the water jet at the
machine itself!
Never direct the water jet at a
power socket!
Never direct the water jet at people
or animals!
Only use power cables which are
in perfect working order! Do not
damage the power cable or repair it
incorrectly!
Never pull the high pressure hose
if it has formed kinks or nooses!
Never pull the hose over sharp
edges!
10
Please note - important!
Lack of water
If the metered quantity of water is too small, you have to use a different
water connection, guaranteeing the necessary output.
Lack of water leads to an accelerated wear of the joints (no guarantee).
The following minimum quantity of water is necessary for a safe and problem-free
operation of the high-pressure cleaner
:
Kränzle 2017, 2017 T: 6,8 l/min, 1,7 Gpm
Kränzle 2020, 2020 T: 7,5 l/min, 1,9 Gpm
Connection to water supply
Please pay attention to the regulations of your waterworks company! In accordance
with DIN EN 61770, the machine may not be directly connected to the public drinking
water supply lines. A brief connection however is permissible according to DVGW
(German Association for Gas and Water Affairs) if a tube ventilator with check valve
(Kränzle Order-No. 41.016 4) is built into the water supply. Also indirect connection
to the public drinking water supply lines is permissible by way of free emission in
accordance with EN 61 770; e.g. by using a reservoir with a float valve.
Direct connection to a non-drinking water supply line is permissible.
Lack of water occurs more often than you
probably believe. The more powerful a
high-cleaner is the greater is the danger
that a lack of water occurs. If there is only
an insufficient amount of water available,
cavitation arises inside the pump, which is
normally noticed too late or even not at all.
The pump will be destroyed!
Please check the available quantity of
water by filling a bucket with litre scale for
one minute.
Electrical connection
The machine is supplied with an electrical power cable with plug. The mains plug must be
fitted to a standard grounded socket with a 30mA residual current operated device. The
socket must be protected
For K2017, K2017T with a 15A or 16A delay action fuse on the mains side.
For K2017, K2017 T, K2020, K2020 T with a 20A delay action fuse on the mains side.
When using an extension cable, this must have an earthed lead which is properly connected
to the socket. The conductors in the extension cable must have a minimum cross section
of AWG14 for K2017, of AWG12 for K2020. Plug connections must be of a spray-proof
design, and may not be located on a wet floor. With extension cables of more than 10 m the
minimum cross section must be AWG12 for K2017, of AWG10 for K2020! When using a
cable drum, always keep the cable wound as far as possible.
Check the line fusing and have the voltage and the available current
intensity checked by an expert in case of uncertainty.
11
Connected load:
Kränzle 2017, 2017 T: 115 V ~, 60 Hz
Kränzle 2020, 2020 T: 115 V ~, 60 Hz
Insufficient quantity of electricity
If there are too many collectors in your
proximity connected to the network at
the same time, the available voltage
and the current intensity may decline.
Consequently the motor of the
high-pressure cleaner does not start or
even blows.
The power supply may also be insufficient
if the power cable is too long or too
thin. If extension cables are too long,
this may lead to a voltage drop causing
malfunctions or start-up difficulties.
12
Kränzle technology
Water and Cleaning System
Water can be connected at mains pressure to the high pressure pump or it can be
sucked directly from a storage tank. The water is then forced under pressure by the high
pressure pump to the lance. The high pressure jet is formed by the nozzle at the end of
the lance.
Environmental, refuse disposal and water protection
regulations must be observed!
Lance with trigger gun
The machine can only be operated when the safety trigger is squeezed. When the
lever is squeezed, the spray gun opens. The liquid is then pumped to the nozzle. The
spray pressure increases and quickly reaches the selected operating pressure. When
the trigger is released, the trigger gun closes and any further spraying of liquid from the
lance is stopped. The pressure gauge must show 0 bar.
The increase in pressure when the trigger gun is closed causes the pressure control
valve-safety valve to open. When the trigger gun is opened, the pressure control valve
- safety valve closes and the pump resumes pressure spraying from the lance with the
selected operating pressure.
The trigger gun is a safety device. Repairs should only
be performed by qualified persons. Should replacement
parts be required, use only components authorized by
the manufacturer.
Pressure control valve - safety valve
The pressure control valve - safety valve protects the machine from a build up of
excess pressure, and is designed not to permit an excess pressure to be selected for
operation. The limit nut on the handle is sealed with a spray coating. The operating
pressure and spray rate can be steplessly adjusted by turning the handle
.
Replacements, repairs, new adjustments and sealing
should only be performed by qualified persons.
13
Motor protection switch
The motor is protected from overload by a motor protection switch, which cuts out the
motor in the event of overload. However should the switch trip frequently, the cause of
the malfunction should be located and rectified (see page 11).
Replacements and inspection work should only be performed
by qualified persons when the machine is disconnected from
the power supply, i.e. with plug pulled out from the electrical
socket.
High pressure hose and spray device
The high pressure hose and spraying device supplied with the machine are made of high
grade material, they are also optimised for the machine and marked as required by the
appropriate regulations.
If replacement parts are required, only such parts that are
authorised by the manufacturer and which bear the markings
required by the appropriate regulations may be used. The
high pressure hose and spray device must be connected in
a pressure-tight manner. The high pressure hose may not be
driven over, pulled excessively, or twisted. The hose may under
no circumstances be pulled over sharp edges, since otherwise
the guarantee is automatically void.
Setting up – Location
Neither set up or operate the machine in rooms where there
is a risk of fire or explosion nor put it into puddles. Do not
use the machine under water.
14
Putting into operation
4.
Put up machine. Release fixing screw
from hexagonal base of hose drum, put
tiltable handle onto the hexagonal base
and fix with screw.
2.
Check water inlet filter for
cleanliness prior to putting the machine
into operation!
Manually unscrew hose attachment. Take
out the serial water inlet filter using needle
nose pliers and clean if filter is soiled.
1.
Move high-pressure cleaner to the
job site.
The Kränzle 2017, 2017 T, 2020, 2020 T
are movable machines with sturdy trolleys
ideally suited for difficult terrain and stairs.
Never pull the machine if the water
supply hose is still connected!
3
. Each time check oil level at the oil
dipstick prior to putting the HP cleaner
into operation. (Take care that cleaner is
in horizontal position!)
The oil level must show between the two
markings.
15
9.
Put HP cleaner into horizontal position.
These machines must be operated in
horizontal position! Unwind HP hose
from hose drum without kinks and nooses.
7.
Push on HP hose to gun.
8.
Screw together HP hose and gun.
10.
Connect water hose to water tank.
The cleaner may be connected to water
mains with cold or 60°C warm water.
Alternatively water can be sucked in from
a container (see page 17).
5.
Push on lance or Dirtkiller lance to gun.
6.
Screw together lance and gun.
Be careful when using hot water!
When running your high pressure cleaner with hot water
of 60° C raised temperatures occur. Do not touch the
metal parts of the cleaner without safety gloves!
16
Putting into operation
12.
Steplessly adjust operating pressure
with handwheel. The maximum pressure
is adjusted ex work.
13.
Ventilation of the machine: Pull and
release the trigger several times.
Switch on high-pressure cleaner with
opened spray gun. Start cleaning task.
11.
Connect to circuit.
Kränzle 2017, 2017 T: 115 V ~, 60 Hz
Kränzle 2020, 2020 T: 115 V ~, 60 Hz
The socket must be protected
For K2017, K2017T with a 15A or 16A delay
action fuse on the mains side.
For K2017, K2017 T, K2020, K2020 T with a
20A delay action fuse on the mains side. .
17
Direct suction
Due the suction capacity of its pump (up to 2.5 m suction height, max. hose length 3 m)
this high-pressure cleaner can suck in water for cleaning purposes from separate
containers or ponds.
Prior to starting the first suction the pump resp. the
suction hose has to be filled with water!
3.
Put filled suction hose into the
container and start the cleaning job.
Use clean water only!
Never suck in water containing
chlorine.
Note
Depending on the water quality it may occur after a prolonged standstill that the valves
get sticky. Consequently the machine cannot properly suck in water from a container.
In this case connect a hose with pressurized water to the pump inlet. Having started the
machine the pressurized water opens the valves and the machine resumes sucking in
water from the container. Now you can carry on with your cleaning task as usual.
F
1.
Mount suction hose with suction filter
(Kränzle accessories No. 15.038 3). When
using other hoses the inner cross section
of the hose must be at least 3/4” = 16 mm.
2.
Fill suction hose with water.
The pH value neutral 7-9 is prescribed for the detergents.
Only use detergents suitable for high-pressure cleaners.
Observe specifications of detergent manufacturer!
e.g.: protective equpment, rules for waste water treatment
etc.
Never suck in liquids containing solvents like varnish
solvents, petrol, oil or similar liquid! Observe specifications
of detergent manufacturers! Seals inside the appliance are
no resistant against solvents! The spray mist of solvents is
highly inflammable, explosive and poisonous
.
18
Suction of detergents
with detergent supply:
For the Kränzle
2017, 2017 T, 2020, 2020 T a built-in injector provides the facility to suck
in detergents.
By pushing the Vario-Jet nozzle to the front the machine is adjusted to low pressure
and a vaccum is build up in the injector. Thus the detergent can be sucked in via the
connected suction hose with filter.
1.
Place chemicals filter into container
with cleansing agent.
2.
To reach the low pressure push Vario
nozzle to the front so that the injector can
suck in the cleansing agent.
3.
The chemicals supply is automatically
stopped when closing the Vario nozzle by
pushing it backwards.
Let cleansing agent take effect and then
spray off with a high-pressure jet.
19
To shut down the pump
01.
Switch off the machine
02. Cut off the water supply
03. Open the spray gun briefly until the pressure is released
04. Apply the safety catch on the spray gun
05. Remove the water hose and spray gun
06. Drain the pump: switch on the motor for approx. 20 seconds
07. Pull the plug from the socket
08. Clean HP hose and wind up
09. Clean power cable and wind up
10. Clean water filter
11. Winter: store the pump in rooms above 0°C
Due to their compact and space saving
design these Kränzle-2017, 2020 cleaners
can be stored practically anywhere.
Store in a place-saving manner
20
Small repairs - do it yourself!
No water from the nozzle but the gauge shows full pressure:
Most likely the nozzle is blocked.
CAUTION! Pull plug from socket prior to starting
any repair work!
If this procedure is not successful, the nozzle has to be dismantled and cleaned or even
replaced, if necessary.
The pressure gauge shows full pressure,
but from the nozzle comes only little water
or no water at all.
(Inside the pressure gauge is no water but
a filling with glycol to damp the vibration of
the pointer.)
Switch off the cleaner. Pull plug from
the socket. Operate gun seveal times to
decrease the pressure.
First unscrew gun and lance, then rinse
hose from any residues.
Check water inlet filter for soiling.
If the problem still exists, take wire (paper
clip) and push through nozzle opening.
Unscrew all 6 valves, one after the other
(hexagonal brass screws, 3 in a row,
vertically and horizontally)
21
Pressure gauge shows little pressure, the water from the nozzle comes
in squirts: Most likely the valves are soiled or sticky.
The pressure gauge shows little
pressure despite fully turned up pressure
regulation. The water from the lance
comes in squirts. The HP hose vibrates.
(Inside the pressure gauge is no water but
a filling with glycol to damp the vibration of
the pointer.)
Take out valve body (with green or red
plastic coating) and O-ring by means
of needle nose pliers. Check O-ring for
damage. In case of a damage the O-ring
has to be replaced.
Take a wire (paper clip) and clean valves
under running water. Also clean valve seat
inside the pump.
Do not forget the O-ring during
reassembly!
22
Small repairs - do it yourself!
The pressure gauge shows full pressure although the gun has
been closed. The pressure switch valve switches constantly.
Possible cause no.1: Leakage
Having closed th gun, the HP cleaner must
shut down and the pressure gauge must
show „0“ bar.
If the pressure gauge still shows full
pressure and the motor constantly
switches on and off, the possible reason
for this can be a leakage of the pump, the
HP hose or the lance.
Proceeding:
Check the connections from the HP clea-
ner to the the HP hose, from the hose to
the gun and also the connection between
lance and gun for tightness.
Switch off the cleaner. Shortly pull the trig-
ger of the gun to decrease the
pressure.
Unscrew HP hose, gun and lance and
check the O-rings.
If the O-rings are damaged they have to
be replaced.
Caution! In case of a leakage there is no guarantee for
possible consequential damages.
23
Unscrew pump outlet.
Take out check ball and check for soiling
or damage of ball or stainless steel seat
inside the pump housing.
Replace non-return valve if necessary.
The pressure gauge shows full pressure although the gun has
been closed. The pressure switch valve switches constantly.
Possible cause no. 2: The return body is soiled
or the sealing ring on the return body is defective.
Caution ! There is no guarantee if the pump is damaged
by defective O-rings due to air induction or lack of water
(cavitation).
24
Type plate (on hand)
Operating manual (on hand)
Protective covering, -device
Pressure line (tightness)
Pressure gauge (function)
Float valve (tightness)
Spraying device (marking)
HP-hose / connector (damage, marking)
Safety valve opens at 10 % / 20 % exceeding of operating pr.
Power cable (damage)
Protective conductor (connected)
On / Off switch
Used chemicals
Allowed chemicals
High-prsure nozzle
Operating pressure..................bar
Switch off pressure................bar
Conductor reist. not exceeded / value
Insulation
Leakage current
Gun locked
The appliance was checked by an expert according to the Guidelines for Liquid
Spray Equipment, the defects found have been rectified so that the Labour Safety can
be confirmed.
The appliance was checked by an expert according to the Guidelines for Liquid
Spray Equipment. The Labour Safety cannot be confirmed unless the defects found are
rectified by repair or replacement of the faulty parts
The next retest according to the Guidelines for Liquid Spray Equipment has to be carried
out by: Month Year
Place, date Signature
Inspection report for HP cleaners
HP cleaners for industrial use have to be checked by an expert every 12 months!
Inspection report on annually carried out Labour Safety Inspection (UVV) according to
the Guidelines for Liquid Spray Equipment. (This inspection sheet serves as proof for
the completion of the retest and must be kept carefully!)
Kränzle test seals: Order no. UVV200106
Scope of inspection o.k. yes no repaired
Inspection data determined value set value
Inspection result (tick)
Owner:
Address:
Type:
Serial no.:
Rep. order no.:
25
Inspection report for HP cleaners
Type plate (on hand)
Operating manual (on hand)
Protective covering, -device
Pressure line (tightness)
Pressure gauge (function)
Float valve (tightness)
Spraying device (marking)
HP-hose / connector (damage, marking)
Safety valve opens at 10 % / 20 % exceeding of operating pr.
Power cable (damage)
Protective conductor (connected)
On / Off switch
Used chemicals
Allowed chemicals
High-prsure nozzle
Operating pressure..................bar
Switch off pressure................bar
Conductor reist. not exceeded / value
Insulation
Leakage current
Gun locked
The appliance was checked by an expert according to the Guidelines for Liquid
Spray Equipment, the defects found have been rectified so that the Labour Safety can
be confirmed.
The appliance was checked by an expert according to the Guidelines for Liquid
Spray Equipment. The Labour Safety cannot be confirmed unless the defects found are
rectified by repair or replacement of the faulty parts
The next retest according to the Guidelines for Liquid Spray Equipment has to be carried
out by: Month Year
Place, date Signature
HP cleaners for industrial use have to be checked by an expert every 12 months!
Inspection report on annually carried out Labour Safety Inspection (UVV) according to
the Guidelines for Liquid Spray Equipment. (This inspection sheet serves as proof for
the completion of the retest and must be kept carefully!)
Kränzle test seals: Order no. UVV200106
Scope of inspection o.k. yes no repaired
Inspection data determined value set value
Inspection result (tick)
Owner:
Address:
Type:
Serial no.:
Rep. order no.:
Kränzle 2017, 2017 T,
Kränzle 2020, 2020 T,
Manfred Bauer, Fa. Josef Kränzle
Rudolf-Diesel-Str. 20, 89257 Illertissen
K
2017 / T
: 408 l/h (102 Gph)
K
2020 / T
: 450 l/h (114 Gph)
machinery directive 2006/42/EEC,
EMC-directive 2004/108 EEC,
noise directive 2005/88/EC, Art. 13,
HP water spraying machines
annex 3, part B, chapter 27
Kränzle 2017, 2017 T: 87 dB (A)
Kränzle 2020, 2020 T: 89 dB (A)
Kränzle 2017, 2017 T: 89 dB (A)
Kränzle 2020, 2020 T: 91 dB (A)
annex V, noise directive 2005/88/EC
EN 60 335-2-79 :2004
EN 55 014-1 :2006
EN 61 000-3-2 :2006
EN 61 000-3-3 :2008
26
EC declaration of conformity
Hereby we declare that:
technical specifications available from:
Nominal flow:
comply with the following guidelines
and their amendments for high-pressure
cleaners:
Sound level measured:
Sound level guaranteed:
Applied conformity evaluation procedures
Applied specifications and standards:
I. Kränzle GmbH
Elpke 97 D - 33605 Bielefeld
Bielefeld, 11.12.2012
Kränzle Josef
(Managing director)
27
Guarantee
The guarantee is only valid for material and manufacturing errors.
Wearing does not fall within this gurantee.
The instructions in our operating manual must be complied with..
The operating instructions form part of the guarantee. The Guarantee is void if other parts
are used than genuine Kränzle accessory parts or genuine Kränzle spare parts.
For high-pressure cleaners sold to the user the guarantee period is 24 month.
For high-pressure cleaners sold for industrial use the guarantee period is 12 month.
In the case of a guarantee please contact your dealer or authorized seller delivering
accessories and your purchase receipt. You can fin them in the internet under
www.kraenzle.com.
The guarantee is also void if the machine is used with exceeding the temperature and
speed limits, a voltage below the required rating, with less than the required amount of
water or with dirty water.
Pressure gauge, nozzle, valves, sleeves, high pressure hose and spray equipment are
wear parts and are not covered by the warranty.
28
Versatile due to Kränzle accessories
Rotating washing brush with 400 mm
extension, Order no. 41 050 1
Underbody lance with 800 mm extension,
Order no. 41 075
Pipe cleaning hose with nozzle,
10 m - Order no. 41 058 1
20 m - Order no. 41 058 2
25 m - Order no. 41 058 3
30 m - Order no. 41 058 4
29
Sludge sucker, stainless steel,
Order no. 41 801
Sludge sucker with 3 m suction hose,
Order no. 41 104
Sand blasting set compl. up to 12 l/min, 150 bar
Order no. 41 068 1
Sand blasting set compl. up to bis 19 l/min, 250
bar Order no. 41 068
Floor cleaner round cleaner UFO
Order no. 41.850
30
Spare parts list
Kränzle 2017, 2017 T, 2020, 2020 T
31
Complete assembly
2 Fahrgestell 1 48.000
3 Versteifungsblech 1 48.010
4 Schraube 6,0 x 30 6 43.423
5 Schraube M 8 x 12 4 40.122
6 Achshalter 1 48.003
7 Schraube M 6 x 40 2 48.012
8 Standfuß links + rechts 1 48.005
10 Käfigmutter M6 2 48.011
11 Schraube 5,0 x 30 2 43.418
12 Rad d210mm 2 44.538
13 Scheibe 40 x 6 x 1,5 (Stahl) 2 45.216 7
14
Kunststoffsenkschraube 5,0 x 20 2 45.421 1
15 Radkappe 2 46.011
16 Gummipuffer 20 x 25 2 48.013
17.1 Frontplatte „K 2017“ 1 48.091 1
17.2 Frontplatte „K 2017 T“ 1 48.091 2
17.3 Frontplatte „K 2020“ 1 48.091 3
17.4 Frontplatte „K 2020 T“ 1 48.091 4
18 Knickschutz 1 48.004
19 Schraube 5,0 x 14 2 43.426
28 O-Ring 9,3 x 2,4 2 13.273
29 Hochdruckschlauch NW 6 10 m (TS-Geräte) 1 43.416
30 Pistole M2000 1 12.480
31.1
Vario-Jet
03 mit Lanze 400 mm 1 41.156 2
32 Schmutz-Killer 03 mit Lanze 400 mm 1 41.073 8
No Description Qty. Ord.-No
32
Spare parts list
Kränzle 2017, 2017 T, 2020, 2020 T
33
Valve housing 18mm
No Description Qty. Ord.-No
1 Ventilgehäuse 1 42.160 3
2 Ventilstopfen 5 41.714
2.1 Ventilstopfen mit R1/4“ IG 1 42.102
3 Dichtstopfen M 10 x 1 1 43.043
4 Ventile (grün) für APG-Pumpe 6 41.715 1
5 O-Ring 16 x 2 6 13.150
6 O-Ring 15 x 2 6 41.716
7 Dichtstopfen R1/4” mit Bund 1 42.103
8 Ausgangsteil (TST) 1 40.522
8.1 Ausgangsteil (TS) 1 40.522 2
9 Dichtstopfen M 8 x 1 2 13.158
10 O-Ring 18 x 2 1 43.446
11 Aluminium - Dichtring 3 13.275
12 Verschraubung Ermeto R1/4” x 8 1 41.042
13 O-Ring 11 x 1,5 1 12.256
14 Edelstahlsitz Ø 7 1 14.118
15 Sprengring 1 12.258
16 Edelstahlkugel Ø10 1 12.122
17 Rückschlagfeder „K“ 1 14.120 1
27 Druckring 3 41.018
28 Manschette 18 x 26 x 4/2 3 41.013
28.1 Gewebemanschette 18 x 26 x 4/2 3 41.013 1
29 Backring 18 x 26 6 41.014
30 O-Ring 28,3 x 1,78 3 40.026
31 Leckagering 18 mm 3 41.066
32 Zwischenring 18 mm 3 41.015 2
33 Verschlussstopfen R3/8“ 1 14.113
34 Kupferring 17 x 22 x 1,5 1 40.019
37 Verschlussschraube M10x1 1 13.385
38 O-Ring 6x1,5 2 13.386
39 Saugzapfen Schlauchanschluss 1 13.236
40 Edelstahlkugel 5,5 mm 1 13.238
41 Edelstahlfeder 1 13.239
42 Kupferring 14 x 20 x 1,5 1 42.104
43 Innensechskantschraube M 8 x 30 2 41.036 1
44 Innensechskantschraube M 8 x 55 2 41.017 1
46 Sauganschluß 1 41.016
47 Wasserfilter 1 41.046 2
48 Gummi Dichtring 1 41.047 1
49 Steckkupplung 1 41.047 4
50 O-Ring 1 41.047 3
Reparatur-Sätze:
Reparatursatz Manschetten 18 mm 41.049 1
bestehend aus je
3 x Pos. 27, 3 x Pos. 28; 3 x Pos. 28.1; 6 x Pos. 29; 3 x Pos. 30
Reparatursatz Ventile für APG-Pumpe 41.748 1
bestehend aus je 6 x Pos. 4; 6 x Pos. 5; 6 x Pos. 6
34
Spare parts list
Kränzle 2017, 2017 T, 2020, 2020 T
35
Unloader valve and pressure switch
No Description Qty. Ord.-No
5 O-Ring 16 x 2 1 13.150
5.1 O-Ring 13,94 x 2,62 1 42.167
8 O-Ring 11 x 1,44 1 12.256
9 Edelstahlsitz 1 14.118
10 Sicherungsring 1 13.147
11 Edelstahlkugel 1 13.148
12 Edelstahlfeder 1 14.119
13 Verschlussschraube 1 14.113
14 Steuerkolben 1 14.134
15 Parbaks 16 mm 1 13.159
16 Parbaks 8 mm 1 14.123
17 Spanstift 1 14.148
18 Kolbenführung spezial 1 42.105
19 Kontermutter M 8 x 1 2 14.144
20 Ventilfeder schwarz 1 14.125
21 Federdruckscheibe 1 14.126
22 Nadellager 1 14.146
23 Handrad AM-Pumpe 1 40.457
24 Kappe Handrad AM-Pumpe 1 40.458
25 Elastic-Stop-Mutter M 8 x 1 1 14.152
26 Manometer 0-250 Bar 1 15.039
27 Aluminium-Dichtring 2 13.275
50 O-Ring 3,3 x 2,4 1 12.136
53 O-Ring 14 x 2 1 43.445
54 Parbaks 4mm 1 12.136 2
57 Blindverschluss mit Dichtungen 1 44.551
58 Parbaks 7mm 1 15.013
70 Steuerkolben kpl. mit Handrad 40.490
36
Spare parts list
Kränzle 2017, 2017 T, 2020, 2020 T
37
Motor
No Description Qty. Ord.-No
1 Ölgehäuse für AP mit Deckel und Dichtung 1 46.530 2
3 Rotor mit Motorwelle (Silumin) 1 43.523
4 Passfeder 6 x 6 x 20 1 41.483 1
5 Motor-Lager B-Seite 6205 - 2Z 1 43.317
6 Motor-Lager Schulterlager 7304 1 41.027
7 Toleranzhülse 1 43.330 1
8 Öldichtung 25 x 35 x 7 1 41.024
9 Lüfterrad BG 90 1 43.319
10 Lüfterhaube BG 90 1 43.320
11 Flachdichtung 1 43.030
12 Innensechskantschraube M 6 x 30 4 43.037
13 Schelle für Lüfterrad mit Schrauben 1 43.454
15 Schraube M 4 x 12 10 41.489
16 Erdungsschraube kpl. 1 43.038
20 Schaltkasten 1 48.001 1
21 Deckel für Schaltkasten 1 44.512
22 Klemmrahmen mit Schalterabdichtung 1 43.453
23 Blechschraube 3,5 x 9,5 2 41.088
24 Dichtung für Deckel 1 44.522
25 Schraube 5,0 x 20 4 43.018
27 Kabelverschraubung PG 13,5 1 40.539
28 Gegenmutter für PG 13,5 1 44.253
29 Kabelverschraubung PG 11 1 41.419
30 Gegenmutter für PG 11 1 44.521
31 Lüsterklemme 3-polig 1 43.326
32 Blechschraube 2,9 x 16 1 43.036
Kränzle 2017, 2017 T, 2020, 2020 T:
2 Motorgehäuse mit Stator Wechselstrom 1 48.090
14 Kabel mit Stecker 20Amp for K2020 1 43.522
without groundfall interruptor
14.1 Kabel mit Stecker 20Amp for Kränzle 2020 1 43.522 1
with groundfall interruptor
14.2 Kabel mit Stecker 15Amp for K2017T 1 43.512
without groundfall interruptor
14.3 Kabel mit Stecker 15Amp for K2017T 1 43.512 1
with groundfall interruptor
18 Kondensator 80 µF 2 43.505
19 Kondensatorhalterung 1 41.116 1
20 Schraube 5,0 x 20 2 43.018
26 Schalter mit 20 A Überstromauslöser 1 43.504
38
Transmission
No Description Qty. Ord.-No
1 Gehäuseplatte für 18 mm Plunger 1 41.020 2
2 Öldichtung 18 x 28 x 7 3 41.031
3 O-Ring Viton 88 x 2 1 41.021 1
4 Plungerfeder 3 41.033
5 Federdruckscheibe 18 mm 3 41.034
6 Plunger 18 mm 3 41.032 1
7 Sprengring 18 mm 3 41.035
8 Taumelscheibe 6,5° (K2017, 2017 T) 1 41.028-6,5
8.1 Taumelscheibe 7,5° (K2020, 2020 T) 1 41.028-7,5
10 Axial-Rillenkugellager 3-teilig 1 43.486
12 Innensechskantschraube M 8 x 30 4 41.036 1
13 Ölstopfen M18x1,5 1 41.011
14 O-Ring 14 x 2 3 43.445
15 Dichtung für Deckel 1 46.531
16 Deckel für Ölgehäuse 1 46.532
17 Schraube M5x12 4 41.019 4
18 Ölverschlussschraube mit Messstab 1 48.017
1 Pistolenschale re+li 1 12.450
2 Schraube 3,5 x 14 10 44.525
3 Reparatursatz M2000 12.454
18 O-Ring 9,3 x 2,4 1 13.273
19 ST 30-Nippel M 22 x 1,5 AG / M 12 x 1 1 13.363
20 Rohr 500 lang, bds. M12 x 1 1 41.527 1
30 Klemmstück 1 41.155 2
31 Halterung für Klemmstück 1 41.155 4
32 Kunstoffhülle 1 41.155 1
33 Vario-Jet 03 (K 2195) 1 41.155 9
33.1 Vario-Jet 042 (K 2160, K 2175) 1 41.155 6
M2000-Pistole kpl. 12.480
Lanze kpl. mit Vario-Jet 03 (K 2195) 41.156 8-03
Lanze kpl. mit Vario-Jet 042 (K 2160, K 2175) 41.156 8-042
39
Gun with lance
No Description Qty. Ord.-No
40
Spare parts list
Kränzle 2017 T, 2020 T
41
Hose drum
No Description Qty. Ord.-No
1 Seitenschale 2 48.101
2 Trommelteil 1 48.102
3 Knickschutz 1 40.162
4 Kunststoffschraube 5,0 x 20 5 43.018
5 Antriebswelle 1 48.104 1
7 Lagerklotz links 1 43.810
8 Schraube 6,0 x 30 4 43.423
9 Lagerklotz rechts 1 43.811
10 Verbindungsrohr 1 48.014
11 Wasser-Eingangsteil 1 48.103
12 O-Ring 6 x 0,8 2 40.177
13 Handkurbel 1 48.108
14 Schraube M 5 x 14 1 40.536
15 Scheibe 5,3 1 50.152
16 Wellensicherungsring 22 mm 2 40.117
17 O-Ring 9,3 x 2,4 1 13.273
18 Dichtsatz 1 13.410 1
19 Saugzapfen Schlauchanschluss 1 13.236
20 Edelstahlkugel 5,5 mm 1 13.238
21 Edelstahlfeder 1 13.239
22 Eingangsinjektror 1 40.317
23 O-Ring 10 x 2 1 43.068
24 O-Ring 6,68 x 1,78 1 40.585
25 Hochdruckschlauch 15m NW6 1 48.015
26 Chemikaliensaugschlauch mit Filter 1 15.038
30 Schlauchtrommel kpl., ohne HD-Schlauch 48.100
42
Dirtkiller with lance
1 Sprühkörper 1 41.520
2 O-Ring 6,88 x 1,68 1 41.521
3 Düsensitz 1 41.522
4 Düse 03 1 41.523 4
5 Stabilisator 1 41.524
6 O-Ring 1 40.016 1
7 Sprühstopfen 1 41.526
8 Rohr 400 mm 2x M 12 x 1 1 41.527
9 ST 30-Nippel M 22 x 1,5 / M 12 x 1 ISK 1 13.363
11 Kappe vorn für Schmutzkiller 1 41.528 1
12 Kappe hinten für Schmutzkiller 03 1 41.542 1
Rep.-Satz Schmutzkiller 03 41.096 1
bestehend aus je 1x 2; 3; 4; 5
Schmutzkiller 03 kpl. mit Lanze 41.073 8
No Description Qty. Ord.-No
43
Wiring diagram
Kränzle 2017, 2017 T, 2020, 2020 T
115 V, 60 Hz
On-Off switch with 20 Ampere
overload protection
Pressure switch
Pump motor
115 V / 60 Hz
Inlet line
115 V / 60 Hz
Made
in
Germany
www.kraenzle.com
S u b j e c t t o t e c h n i c a l m o d i f i c a t i o n s .
I . K r ä n z l e G m b H
E l p k e 9 7
D - 3 3 6 0 5 B i e l e f e l d
R e p r i n t o n l y a l l o w e d w i t h t h e a u t h o r i s a t i o n o f K r ä n z l e .
A s d a t e o f 2 6 . 0 1 . 2 0 1 3
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kranzle K2020T bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kranzle K2020T in de taal/talen: Engels als bijlage per email.

De handleiding is 2,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info