Handleiding Korg Electribe ESX-1 (pagina 94 van 108) (Engels)

488477

Verklein

Vergroot

Pagina terug

1/108

Pagina verder

5. Make settings on your external MIDI device (mas-

ter) so that it will transmit MIDI clock messages.

6. Return to Pattern mode or Song mode.

7. When you start the sequencer of your external MIDI

device, the ESX-1 will playback in synchronization

with it.

If MIDI clock messages are being received at the

MIDI IN connector, you can press the ESX-1’s

PLAY/PAUSE key to make it start playing in syn-

chronization to the tempo of your external MIDI

device.

If the ESX-1’s MIDI Clock setting is “Ext” or “Auto”

and it is synchronized to an external MIDI clock, it

will follow the tempo of the external sequencer; you

will be unable to adjust the tempo on the ESX-1.

If the ESX-1 receives a MIDI Start message while

synchronized to MIDI clock, it will begin playing from

the beginning of the currently-playing pattern (in

the case of a song, the beginning of the pattern

that was playing when the Start message was re-

ceived).

Playing back in sync with other

Electribe models

You can enjoy even greater possibilities by playing the ESX-

1 in sync with other models in the Electribe series such as

the Electribe-MX (EMX-1), Electribe-S (ES-1) or Electribe-

M (EM-1).

To make the ES-1 play in synchronization to the tempo

of the ESX-1

Use a MIDI cable to connect the ESX-1’s MIDI OUT

connector to the ES-1’s MIDI IN connector. Use

audio cables to connect the ES-1’s line output jacks

to your mixer or powered monitor system (ampli-

fied speakers).

1. Press the Global key (it will light).

2. Press the [

] cursor key to change the display to

read “Clock.”

3. Turn the dial of each device to set the ESX-1 to “Int”

and the ES-1 to “Ext.”

4. Press the ESX-1’s PLAY/PAUSE key to start the pat-

tern or song (the PLAY/PAUSE key will light). The

ES-1 will play in sync with the ESX-1’s tempo.

If the MIDI channel of one of the ESX-1’s parts

matches the ES-1’s MIDI channel, the ES-1 may

sound in unison with the ESX-1. If this occurs,

change the MIDI channel settings so that they do

not conflict.

To make the ESX-1 and ES-1 play back the identically-

numbered pattern in synchronization

1. Press the Global key (it will light).

2. Press the [

] key to change the display to read

“Clock.”

3. Set the ESX-1 to “Int” (master) and the ES-1 to “Ext”

(slave).

4. Set the ESX-1’s keyboard part 1 and the ES-1 to the

same MIDI channel.

For example, set both to “01”.

5. Set the ESX-1’s MIDI Filter parameter “P” to “O”.

Set the ESX-1’s MIDI Filter parameter “N” to “X”.

About the MIDI messages used

for synchronization

The MIDI messages used for synchronization (Realtime

Messages) are Timing Clock [F8], Start [FA], Continue [FB],

and Stop [FC].

Only one master device (e.g., sequencer) in the connected

system can transmit these messages; the remaining slaved

devices (sequencers) will receive these messages.

Timing Clock

The slave device calculates its own tempo accord-

ing to the Timing Clock messages it receives from

the master device. Twenty-four Timing Clock mes-

sages are transmitted during each quarter note.

If you set the ESX-1’s MIDI mode CLOCK setting

to “Auto,” it will act as a slave (it will receive

Realtime Messages). However if the ESX-1 is not

receiving any Timing Clock messages, it will oper-

ate according to its own internal clock even with

the “Auto” setting.

Start

The Start message tells the slave device when to

begin playing. A Start message is transmitted when

you press the PLAY/PAUSE key. When a slave de-

vice receives the Start message, it will begin play-

ing from the beginning in synchronization with the

incoming Timing Clock messages.

Continue, Stop

If you press the START/PAUSE key on the master

device while it is paused, the master device will

transmit a Continue message. When a slave device

receives the Continue message, it will resume play-

back from the location at which it is currently

stopped. If you press the STOP key during play-

back, the master will transmit a Stop message.

When a slave device receives the Stop message, it

will stop playback.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Korg Electribe ESX-1 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info