533104
4
Verklein
Vergroot
Pagina terug
1/125
Pagina verder
4
will flash a few times right after battery installation. Make sure the vane is pointing due north at the
moment when the red LED flashes and the calibration is now completed. Replace the battery cover and
tighten the screws.
(4) If the wind vane is not pointing due north when the red LED first flashes, remove the batteries and
repeat steps 2 and 3.
(5) Hold the “CHANNEL/SEARCH” buttons on the monitor to search for a remote transmitter. Wind
direction, wind speed, wind chill and channel-1 temperature/humidity readings will appear within
10 minutes if the RF transmission is successful.
5. Selecting a location for the rain gauge
Select a mounting location for the rain gauge that is:
- A flat, level surface
- Within 50 meters (164 feet) of open area from the monitor. Reduce the distance if there are obstacles
between the rain gauge and the monitor
- In an area not blocked on the top or on the sides, so that rain can freely reach the rain gauge (for example,
not under an overhang or too close to a building or fence)
Caution:
- To prevent false rainfall readings caused by water splashes, do not choose a location that is not level or
that is too close to the ground, near a swimming pool or lawn sprinklers, or anywhere water might
accumulate or run off
- The screen in the cylinder of the rain gauge filters most debris (such as leaves) that might fall into the rain
gauge. To avoid frequent build-up of debris in the cylinder, do not mount the rain gauge too close to trees
or plants
6. Battery installation for the rain gauge
(1) Unscrew the 2 screws at each side of the transmitter. Carefully lift the top casing from the base.
(2) Unscrew the 4 screws from the battery compartment cover (identifiable by the battery diagram
markings). Remove the cover and insert 2 AA alkaline batteries as indicated by the polarity symbols
marked inside the battery compartment.
(3) The rain cup has been sealed to prevent tipping and damage during shipping. Before first use, please
remove the seal to allow the rain cup to fill and empty when rainfall occurs.
(4) Replace the battery compartment cover and the screws.
(5) Carefully replace the casing on top of the base. Replace the screws.
(6) Hold the “CHANNEL/SEARCH” button on the monitor for 3 seconds and the total rainfall “- - - -” will
flash. The monitor is now searching for all remote sensors. The total rainfall reading (in this case “0” mm
or inch) will appear within 2 minutes if the RF transmission is successful and the monitor and rain gauge
are now within the effective transmission range.
(7) If total rainfall “- - - -” stops flashing and stays on the display after 2 minutes of searching, the RF
transmission has failed. Shorten the distance between the monitor and rain gauge. Reset the rain
gauge by removing all batteries from the rain gauge and wait for 10 seconds before reinstalling the
batteries. Then repeat steps 5 (and 6) until the RF communication is completed.
7. Mounting the rain gauge
Before mounting the rain gauge, make sure the rain gauge and monitor are within the effective transmission
range and batteries are installed.
(1) Hold the base of the rain gauge flat against the mounting surface then use a level to make sure the rain
gauge (as it rests on the mounting surface) is horizontally level.
(2) Use a pencil to trace the inside of the mounting holes on the base of the rain gauge to mark the screw
locations.
(3) Drill a hole in the center of each marked location and insert the supplied plastic screw plugs.
(4) Hold the rain gauge against the mounting surface so that the holes on the base are aligned with the
plugs, then thread the supplied washer head screws into each hole and use a screwdriver to tighten
them.
OPERATION
Names and functions of buttons:
Press Functions Hold 3 seconds
RAIN/CLEAR Read daily/monthly/weekly/total rainfall Clear rainfall record
RAIN HISTORY Read current and past 6 days, weeks or months rainfall data
WIND Read average and gust wind speed
4

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Konig-KN-WS600

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Konig KN-WS600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Konig KN-WS600 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,47 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info