508628
35
Verklein
Vergroot
Pagina terug
1/42
Pagina verder
HAV-TT25USB
MANUAL (p. 2)
USB turntable
2
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS FOR AUDIO PRODUCTS
-READ THOROUGHLY
When using electrical products, basic precautions should always be followed including:
1. Read Instructions - All the safety and operating instructions should be read before the product is
operated.
2. Retain Instructions - The safety and operating instructions should be retained for future reference.
3. Heed Instructions - All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions - All operating and user instructions should be followed.
5. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Attachments - Do not use attachments not recommended by the product manufacturer as they may
cause hazards.
7. Water and Moisture - Do not use this product near water-for example, near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, Etc.
8. Accessories - Do not place this product on an unsteady surface. The product may fall, causing serious
injury to a child or an adult and serious damage to the product. Use only with a stand, bracket, or table
recommended by the manufacturer, or sold with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a mounting accessory recommended by the
manufacturer.
9. Transporting - This product should be moved with care to avoid damage or injury.
10. Ventilation - Slots and openings in the cabinet are provided for ventilation, to ensure
reliable operation of the product and to protect it from overheating. These openings
must not be blocked or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or similar surface. This product should not be placed in a
built-in installation such as a bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
11. Power Sources - This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your product dealer
or local power company. For products intended to operate from battery power, or other sources, refer to
the operation instructions.
12. Power - Cord Protection - Power-supply cords should be routed so that they are not likely to be trapped
in any way.
13. Main plug - The main plug is used as the disconnect device, the disconnect device shall remain readily
operable.
14. Lightning - For added protection for this product during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and power-line surges.
15. Power Lines - An outside antenna system should not be located in the vicinity of overhead power
lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be taken to keep from touching such power
lines or circuits as contact with them might be fatal.
16. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this
can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind into this product through openings as they
may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never
spill liquid of any kind on the product. The apparatus shall not be exposed to dripping or splashing and no
object filled with liquids, such as vases, shall be placed on the apparatus.
18. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
3
a. If the power-supply cord or plug is damaged.
b. If liquid has spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions, as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to its normal operation.
e. If the product has been dropped or damaged in any way, and the product exhibits a distinct change in
performance-this indicates a need for service.
20. Replacement Parts - When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
21. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
22. Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves
or other products (including amplifiers) that produce heat.
BEFORE USE
1. Before use, please remove and dispose of all the packaging. Remember to keep the packaging away
from children and pets.
2. Choose the location of the unit installation carefully. Avoid placing it in direct sunlight or close to a source
of heat. Also avoid locations subject to vibrations and excessive dust, cold or moisture. Keep away from
sources that hum, such as transformers or motors.
3. Do not open the cabinet as this might result in damage to the circuitry or electrical shock, if a foreign
object should get into the set, contact your dealer.
4. Be sure not to handle a record with dirty fingers. Never insert a record that has a crack on the surface.
5. When removing the power plug from the wall outlet, always pull directly on the plug, never pull the cord.
6. Do not attempt to clean the unit with chemical solvents as this might damage the finish. Use a clean, dry
cloth.
7. In order to completely shut off the power to this product -, unplug the power cord from the wall outlet. Be
sure to unplug the unit if you do not intend to use it for an extended period of time, such as a vacation.
8. Keep this manual in a safe place for future reference.
Care and maintenance
• Topreventfireorshockhazard,disconnectyourunitfromtheACpowersourcewhencleaning.
• Ifthecabinetbecomesdusty,wipeitwithasoftdrycloth.Donotuseanywaxorpolishspraysonthe
cabinet.
• Thisproductisnotintendedforcommercialuse.Householduseonly.
• Neverallowanywaterorotherliquidstogetinsidetheunitwhilecleaning.
FUNCTION DESCRIPTIONS
CONNECTIONS
4
Caution:
• Switchoffthepowertoallequipmentbeforemakingconnections.
• Readtheinstructionsofeachcomponentyouintendtousewiththisunit.
• Besuretoinserteachplugsecurely.Topreventhumandnoise,avoidbundlingthesignalinterconnection
cables together with the AC power cord.
A USB Host Socket
Connect one end of the USB cable to the USB host socket on the unit and the other end to the USB
host socket on your computer.
B LINE OUT Socket
Connect one end of the RCA LINE OUT cable into the LINE OUT socket, and the other end into the
auxiliary input (AUX) socket on your home amplifier device, matching the colors to the proper plug
and socket.
C AC Power Cord
Plug this power cord into an AC wall socket.
D FM ANTENNA
Extend and relocate the antenna when listening to a radio in FM mode.
PARTS OF THE TURNTABLE
A TURNTABLE
B 45 RPM ADAPTOR
Use the adaptor when playing a 45-rpm record.
C TONEARM CONTROL INDICATOR
The indicator lights are switched on when the tone arm is activated.
D DECORATION (NOT FOR TONEARM ADJUSMENT)
E TONE ARM
F TONE ARM REST
Place the tone arm back to the tone arm rest when playback stops.
G SPEED SELECTOR
Select a proper speed for your record before playing.
H STYLUS
I NEEDLE COVER
5
UNIT FUNCTIONS
1. PLAY/PAUSE
]
I
Use to start playback/pause in USB/CARD mode; Press to listen to a preset radio station in TUNER mode.
2. STOP/BAND
Use to stop playback or end recording to USB/CARD. Use to cycle alternately from AM and FM.
3. Fast forward
In USB/CARD mode, press to go to the start of the next track.
In FM/AM mode, press to search for a station on step frequency; hold to search for the nearest station.
4. Fast reverse
In USB/CARD mode, press once to go back to the start of the current track; press twice to go back to the
start of the previous track.
In FM/AM mode, press to search for a station on step frequency; hold to search for the nearest station.
5. STANDBY BUTTON
Press to switch on the appliance or put it on standby.
6. DELETE BUTTON
In stop mode, hold to access delete mode.
7. MEMORY/MODE BUTTON
In TUNER mode, press to store your tune-in station.
In USB/CARD mode, press to select a mode: repeat 1, repeat album, repeat all, shuffle, intro and cancel.
In STANDBY mode, hold to enter time setting function.
8. FUNCTION BUTTON
Press repeatedly to select functions: PHONO, TUNER, USB, CARD.
9. BIT/REC BUTTON
Hold to select recording quality: 64 kbps, 128 kbps, 192 kbps.
Press briefly to confirm bit-rate setting or begin recording.
10. VOLUME KNOB
Rotate to adjust the volume level.
11. POWER LED INDICATOR
When the unit is powered on, the power indicator will light up.
12. DISPLAY
13. RECORD LED INDICATOR
When it is recording, the record indicator will light up.
14. USB SLOT
Connect your USB device to the USB slot.
15. SD SLOT
Connect your SD/MMC card into the CARD slot.
16. DUST COVER
Close the dust cover when playing a vinyl record to keep dust away. Do not place any heavy objects on
top of the cover especially when playing a record.
6
BASIC OPERATION
1. Connect the AC power cord to the AC outlet and the power indicator will illuminate.
2. Press the STANDBY button to turn the unit on.
3. Press the FUNCTION button repeatedly to select your desired source: PHONO, TUNER, USB or CARD.
4. Rotate the VOLUME knob to adjust the sound level.
5. Press the STANDBY button again to put the appliance on standby.
6. To completely switch off the appliance, you need to disconnect the power plug from the electrical outlet.
HOW TO SET THE TIME
Switch on the appliance first, and then press the STANDBY button to switch to standby mode.
1. Hold the MEMORY/MODE button, 24 HOUR will appear on the display. Press the
or
button to
switch between 12 and 24 hour mode. Then press the MEMORY/MODE button to confirm the setting.
NOTE: If no operation is performed within approximately 10 seconds after you hold the MEMORY/MODE
button, the appliance will exit the time setting mode automatically and the setting is not memorized.
2. After you have set the 12/24 hour mode, hour digits will flash on the screen. Press the
or
button
to set the hour. Press the MEMORY/MODE button again to confirm the setting, then minute digits will
flash on the screen. Press the
or
button to adjust the minutes. After the minutes have been
adjusted, press the MEMORY/MODE button again to confirm the setting and exit the time setting mode.
NOTE: When setting in the 12 hour mode, ‘AM’ or ‘PM’ will also flash with the hour digits. Make sure the
time has been set correctly with an AM or PM indicator.
LINE OUT OPERATION
1. Plug one end of the LINE OUT cable (included) into the LINE OUT socket at the back of the unit.
2. Plug the other end of the cable into the LINE IN socket of your home amplifier device.
3. Switch on the unit.
4. Turn on the volume control if available.
LISTENING TO A RECORD
Cartridge
Stylus assembly
Getting started
Your turntable player can play 33, 45 & 78-RPM records
-- Remove the stylus protector first.
-- Turn the volume knob, which is located at the front of the unit, to adjust to your desired volume level.
-- Place a record (the record is not included) on the platter. Be sure not to handle the record with dirty
fingers. Never play a record that has a crack on the surface.
PLAYING A RECORD
Press the FUNCTION button to select PHONO (normally PHONO is the default function) and ‘PHONO’ will
appear on the display.
7
Slide the speed selector (33/45/78) to the proper position depending on the record to be played.
Place a record on the turntable platter (remember to use the 45RPM spindle adaptor if required when playing
a 45RPM record).
Lift the tone arm from the rest and slowly move it above the side of the record.
TONE ARM CONTROL INDICATOR will light up. The turntable will begin to rotate.
Place the tone arm to the desired position of the record.
Adjust the volume knob to the desired level.
To pause or stop playing, you need to lift and move the tone arm back to the tone arm rest stand manually.
ADAPTOR
At the end of the record, the turntable will automatically stop rotating. Lift the tone arm from the center of the
record and return it to the desired position.
To stop it manually, lift the tone arm and return it to the arm rest.
NOTE:Toplaya45-rpmrecordwhichhasthecenterclipmissing,rstplacethe45-rpmadaptor(therecord
is not included) located at top right hand of the apparatus onto the spindle.
It is strongly recommended to play records with the transparent dust cover closed. Also please do not place
anything on top of the dust cover especially when playing a record. If you hear a distorted sound please
check whether the stylus is worn out. (Please refer to “How to replace the Turntable Stylus (Needle)”)
How to replace the Turntable Stylus (Needle)
Guide Pins (inside)
8
Removing the old stylus
1. Set a screwdriver at the tip of the stylus and push down in the direction “A”.
2. Remove the stylus by pulling it forward and down.
Installing a new stylus
1. Hold the tip of the stylus and insert the other edge by pressing in the direction “B”.
2. Push up in the direction “C” until it locks at the tip.
LISTENING TO THE RADIO
1. Press the FUNCTION button repeatedly until it switches to TUNER function.
2. Press the STOP/BAND button repeatedly to select either FM or AM.
3. Press the skip button (
or
) repeatedly to search for a radio station at a certain step frequency.
Or, hold the skip button until the frequency starts to change then release the button, the appliance will
stop searching when the nearest radio station is found.
4. For your convenience, store your desired station in memory so that you can enjoy your favourite station
immediately.
NOTE: You can store up to 20 stations on the appliance.
• SimplypresstheMEMORY/MODEbutton,‘01’willflashandpresstheMEMORY/MODEbuttonagain
to memorize the radio station.
HOW TO LISTEN TO A PRESET STATION
In TUNER mode, press the PLAY/PAUSE button (
]
I
) repeatedly to select a preset station in an increased
sequence.
The ST indicator will appear on the display when the radio is broadcasting in stereo, while the MONO
indicator will appear when the signal becomes weak.
If the reception is poor in the following bands:
AM: Turn the unit around to find the best position for AM stations.
FM: Extend and turn the FM antenna around so that you can receive the station clearly.
MEDIA SOURCE
CONNECT YOUR AUDIO DEVICE
• USBFLASHDEVICE:ConnectyourUSBflashdevicethroughtheUSBhostsocketinfrontofthe
appliance.
• CARD:Insertyourcardintothecardslotwiththeprintedlabelfacingup.
SD card inserted correctly SD card inserted incorrectly
CARD MAINTENANCE:
* If the card becomes dirty, wipe the surface with a soft, dry cloth.
* Cards should be returned to their cases after use to avoid dust.
* Do not expose the card to direct sunlight or high humidity and temperatures for extended periods.
IMPORTANT: Switch to another function before you remove your USB flash device.
CAUTION:
• Ittakessometimefortheappliancetoreadthemediadevices(cardandtheUSBdevice)in
accordance with their capability especially in recording mode. Wait patiently until ‘REC’ appears on
the display.
• Duringrecordingmode,ifboththeUSBflashdeviceandCARDareconnectedtotheappliance,
press the BIT/REC button and then press the
or
button to switch between USB and card.
Press the BIT/REC button again to confirm and start recording.
9
PLAY THE USB HOST
1. Press the FUNCTION button repeatedly until the USB function is selected.
2. Insert an external audio source (i.e. MP3 player) into the USB slot and the display will show ‘USB’ and
soon after will show ‘READING’.
Note: If the USB device is not detected, ‘NO USB’ will appear on the display.
3. Normally, tracks will be played automatically.
4. Press the PLAY/PAUSE (
]
I
) button to interrupt/resume the playback.
5. Stop the playback by pressing the stop (
*
) button.
ADVANCED FEATURES
6. Press the
button to go the start of the next track.
7. Press the
button once to go back to the start of the current track. Press the
button twice to skip
to the previous track.
8. Playback mode
During playback, press the MEMORY/MODE button repeatedly to cycle from repeat 1, repeat album,
repeat all, shuffle, intro and cancel.
REPEAT 1: The current track will be repeated continuously.
REPEAT ALBUM: The current folder will be played continuously.
REPEAT ALL: All tracks will be played continuously.
SHUFFLE: Tracks will be played in a random sequence.
INTRO: Tracks will be played for 12 seconds in sequence.
CANCEL: Press the MEMORY/MODE button again to cancel playback mode.
TIP: Press the STOP button and the playback mode will be cancelled.
9. Program functions
A. Press the STOP button and then press the MEMORY/MODE button to enter program mode.
B. ‘00’ will flash on the screen. Press the skip button to select a folder and press the MEMORY/MODE
button to confirm.
C. Then ‘00’ will flash to prompt you to select a track. Press the skip button to select a track then press
the MEMORY/MODE button to add the track to the program list.
D. Follow step A and B to keep programming. You can add up to 20 tracks to the program list.
E. If you need to clear a programmed track during programming, simply press the DELETE button.
You can only delete from the last track. During playback mode, press the STOP button and then
press the MEMORY/MODE button to enter program mode. Then press the DELETE button to start
clearing from the last track.
F. After you finish programming, press the PLAY/PAUSE button to start playing.
G. To stop playback, press the STOP button. The ‘PROGRAM’ indicator will remain on the display.
H. To view the tracks in the program list, press the STOP button to enter the stop state in program
mode, then keep pressing the MEMORY/MODE button.
I. To cancel the program function, press the STOP button twice and the ‘PROGRAM’ indicator at the
bottom of the display will disappear.
10. Delete function
Press the STOP button and then hold the DELETE button. Press the
or
button to select
DELETE ONE, DELETE DIR, DELETE ALL.
10
DELETE ONE: Press the
or
button to select a track, or press the
or
button until the
desired folder is reached. Then press the DELETE button once, “DEL ONE” will appear on the display,
press this button again to start deleting the current track.
DELETE DIR: If you wish to delete a certain folder in your device, press the
or
button until your
desired folder has been reached. Then hold the DELETE button and press the
or
button to select
DEL DIR. Press the DELETE button again to delete the current folder.
DELETE ALL: Hold the DELETE button and press the
or
button to select DEL ALL. Press the
DELETE button again to delete all files in your USB device.
NOTE: All delete features are PERMANENT and CANNOT BE UNDONE. Before you press the DELETE
button again to start the deleting process, press the STOP button to quit the delete function.
RECORD TO USB
1. Insert an external audio source (i.e. MP3 Player) into the USB slot.
2. Press the FUNCTION button repeatedly to select your desired recording source (PHONO or FM).
3. Set your recording bit rate.
Hold the BIT/REC button for more than 2 seconds and wait until ‘128KBPS’ appears on the display.
Press the
or
button to select 64KB, 128KB or 192KB. Then press the BIT/REC button to confirm
the setting. Then press the BIT/REC button again to start recording.
Or, you can just press the REC button briefly to record tracks at 128 KB (default bit rate) into the USB
device.
NOTE:
• WhenboththeUSBflashdeviceandCARDareconnectedtotheappliance,presstheBIT/REC
button and then press the
or
button to switch to USB. Press the BIT/REC button again to
confirm and start recording.
• Ittakessometimefortheappliancetoreadthemediadevices(cardandtheUSBdevice)in
accordance with their capability.
• Duringtheentirerecording,theRECORDINDICATORwilllightupinred.Recordingwillnotbegin
until ‘REC’ appears on the display.
4. Press the STOP button again to complete the recording and the RECORD INDICATOR will fade out.
NOTE:
1. The bit rate must be set if you do not use the default bit rate for recording.
2. When “REC ERR” appears, check if your media device is loosened.
3. No song title will be recorded during encoding mode.
4. Some USB drives may not be supported for recording if they are not formatted in a supported
parameter.
5. The unit cannot play music files directly from your PC. MP3’s must be stored on a portable memory
device, such as a SD/MMC CARD, and inserted into the unit’s USB or SD/MMC SLOT.
PLAY THE MMC/SD CARD
1. Press the FUNCTION button repeatedly until the CARD function is selected.
2. Insert a SD/MMC card into the SD/MMC slot and the display will show ‘USB’, and soon after will show
‘READING’.
Note: If the card is not detected, ‘NO CARD’ will appear on the display.
11
3. Normally, tracks will be played automatically.
4. Press the PLAY/PAUSE (
]
I
) button to interrupt/resume the playback.
5. Stop the playback by pressing the stop (
*
) button.
ADVANCED FEATURES
6. Press the
button to go the start of the next track.
7. Press the
button once to go back to the start of the current track. Press the
button twice to skip
to the previous track.
8. Playback mode
Press the MEMORY/MODE button repeatedly to cycle from repeat 1, repeat album, repeat all, shuffle,
intro and cancel.
REPEAT 1: The current track will be repeated continuously.
REPEAT ALBUM: The current folder will be played continuously.
REPEAT ALL: All tracks will be played continuously.
SHUFFLE: Tracks will be played in a random sequence.
INTRO: Tracks will be played for 12 seconds in sequence.
CANCEL: Press the MEMORY/MODE button again to cancel playback mode.
TIP: Press the STOP button and the playback mode will be cancelled.
9. Program functions
A. Press the STOP button and then press the MEMORY/MODE button to enter program mode.
B. ‘00’ will flash on the screen. Press the skip button to select a folder and press the MEMORY/MODE
button to confirm.
C. Then ‘00’ will flash to prompt you to select a track. Press the skip button to select a track then press
the MEMORY/MODE button to add the track to the program list.
D. Follow step A and B to keep programming. You can add up to 20 tracks to the program list.
E. If you need to clear a programmed track during programming, simply press the DELETE button.
You can only delete from the last track. During playback mode, press the STOP button and then
press the MEMORY/MODE button to enter program mode. Then press the DELETE button to start
clearing from the last track.
F. After you finish programming, press the PLAY/PAUSE button to start playing.
G. To stop playback, press the STOP button. The ‘PROGRAM’ indicator will remain on the display.
H. To view the tracks in the program list, press the STOP button to enter the stop state in program
mode, then keep pressing the MEMORY/MODE button.
I. To cancel the program function, press the STOP button twice and the ‘PROGRAM’ indicator at the
bottom of the display will disappear.
10. Delete function
Press the STOP button and then hold the DELETE button. Press the
or
button to select
DELETE ONE, DELETE DIR, DELETE ALL.
DELETE ONE: Press the
or
button to select a track, or press the
or
button until the
desired folder is reached. Then press the DELETE button for once, “DEL ONE” will appear on the
display, press this button again to start deleting the current track.
12
DELETE DIR: If you wish to delete a certain folder in your device, press the
or
button until your
desired folder has been reached. Then hold the DELETE button and press the
or
button to select
DEL DIR. Press th DELETE button again to delete the current folder.
DELETE ALL: Hold the DELETE button and press the
or
button to select DEL ALL. Press the
DELETE button again to delete all files in your card.
NOTE: All delete features are PERMANENT and CANNOT BE UNDONE. Before you press the DELETE
button again to start the deleting process, press the STOP button to quit the delete function.
RECORD TO SD/MMC CARD
1. Insert a SD/MMC card into the SD/MMC slot.
2. Press the FUNCTION button repeatedly to select your desired recording source (PHONO or FM).
3. Set your recording bit rate.
Hold the BIT/REC button for more than 2 seconds and wait until “128 KBPS” appears on the display.
Press the
or
button to select 64KB, 128KB or 192KB. Then press the BIT/REC button to confirm
the setting. Then press the BIT/REC button again to start recording.
Or, you can just press the REC button briefly to record tracks at 128 KB into the USB device.
NOTE:
• WhenboththeUSBflashdeviceandCARDareconnectedtotheappliance,presstheBIT/REC
button and then press the
or
button to switch to CARD. Press the BIT/REC button again to
confirm and start recording.
• Ittakessometimefortheappliancetoreadthemediadevices(cardandtheUSBdevice)in
accordance with their capability.
• Whenrecording,theRECORDINDICATORwilllightupinred.Recordingwillnotbeginuntil‘REC’
appears on the display.
4. Press the STOP button again to complete the recording.
NOTE:
1. When “REC ERR” appears, check if your media device is loosened.
2. No song title will be recorded during encoding mode.
3. Some USB drives may not be supported for recording if they are not formatted in a supported
parameter.
4. The unit cannot play music files directly from your PC. MP3’s must be stored on a portable memory
device, such as a SD/MMC CARD, and inserted into the unit’s USB or SD/MMC SLOT.
USB AND SD/MMC CARD (RECORD WITH EACH OTHER)
RECORD TO SD/MMC CARD FROM USB
1. Insert the USB and CARD at the same time.
2. Press the FUNCTION button repeatedly until the USB function is selected.
• Ifyouwanttorecordtrackstothecardinafastspeed,presstheSTOPbuttontostoptheplayback.
3. Press the
or
button to select a track, or press the
or
button until the desired folder is
reached.
4. Press the BIT/REC button and press the
or
button to select the record mode: REC ONE, REC
DIR, REC ALL, and then press the REC button to copy tracks into the SD/MMC card.
NOTE:
• Inplaybackmode,presstheBIT/RECbuttonbriefly,atrackwillbecopiedandplayedfromthevery
beginning.
• Instopmode,pressBIT/RECbuttonbriefly,atrackwillbecopiedmuchfasterwiththepercentage
shown on the right hand side.
13
• TheCARDindicatoratthetopofthedisplaywillflashtoindicatetotheuserthatitiscopyingtothe
CARD.
RECORD TO USB FROM MMC/SD
1. Insert the USB and CARD at the same time.
2. Press the FUNCTION button repeatedly until the CARD function is selected.
• IfyouwanttorecordtrackstotheUSBdeviceinafastspeed,presstheSTOPbuttontostopthe
playback.
3. Press the
or
button to select a track, or press the
or
button until the desired folder is
reached.
4. Press the BIT/REC button and press the
or
button to select the record mode: REC ONE, REC
DIR, REC ALL, and then press the REC button to copy tracks into the USB device.
NOTE:
• Inplaybackmode,pressBIT/RECbuttonbriefly,atrackwillbecopiedandplayedfromthevery
beginning.
• Instopmode,pressBIT/RECbuttonbriefly,atrackwillbecopiedmuchfasterwiththepercentage
shown on the right hand side.
• TheUSBindicatoratthetopofthedisplaywillflashtoindicatetotheuserthatitiscopyingtothe
USB.
NOTE: When “REC FULL” is shown on the display during recording, the USB or SD CARD is full, without
enough space to continue recording.
If you want to proceed with the recording, please delete tracks on the USB device or CARD, or change to
a new USB device or CARD.
AUDACITY SOFTWARE
Audio from PHONO, RADIO, USB and SD card can be recorded onto the computer.
• PresstheFUNCTIONbuttonrepeatedlyuntilthePHONOfunctionisselected.Placearecordontothe
platter, and select a speed to prepare for playback.
• PresstheFUNCTIONbuttonrepeatedlyuntiltheTUNERfunctionisselected,thenpressthe
STOP/BAND button to select FM (or AM if desired). The recording quality may be affected by the poor
AM reception. Tune to your desired station.
• PresstheFUNCTIONbuttonrepeatedlyuntiltheUSBfunctionisselected.
• PresstheFUNCTIONbuttonrepeatedlyuntiltheCARDfunctionisselected.
The CD provided contains the following software:
(1) audacity-src-1.2.6----------For source codes
(2) Audacity_for_MAC---------For Macintosh
(3) Audacity_for_WIN----------For Windows
(4) AUTORUN.INF
(5) The GNU General Public License.html
The software is compatible with Windows 98, 2000, ME, XP, VISTA, 7 and Macintosh.
14
AUDACITY INSTALLATION AND USB CONNECTION
Connect one end of USB cable to the appliance and the other end to your computer. Then connect the AC
power cord of the appliance. Press the STANDBY button to switch the appliance on.
NOTE: If you wish to listen while downloading to your computer, turn the VOLUME knob and adjust to
your desired volume level. However, the playback volume level on the unit doesn’t affect the downloading
volume level.
AUDACITY FOR WINDOWS
Installing the Audacity Software
1. Please insert the Audacity Software disk that comes with your unit. Go to My Computer and double click
the CD ROM Drive.
2. There are five folders in the Audacity disk. Select Audacity_for_WIN for Windows system, and select
Audacity_for_MAC for Macintosh system.
3. Double click the Audacity_for_WIN for Windows system, and double click the audacity-win-1.2.6 to install
the Audacity Software.
15
4. The Audacity Setup Wizard will appear. Click Next to install the software.
5. Click on “I accept the agreement” and click Next.
6. Continue to click on the Next buttons.
16
7. Click the Install button to start installation.
17
8. Click Finish to complete installation.
9. You can now open the Audacity Software and start recording your files.
NOTE: Once you set up Audacity, you do not need to re-set it with each use.
(For additional information regarding Audacity features & applications, please visit the Audacity website at
www.audacity.sourceforge.net)
18
CONFIGURING AUDACITY FOR MICROSOFT WINDOWS
Audacity Interface
Audacity Control Buttons
Use the attribute controls button at the top of the screen to go to beginning, Play, Record, Pause, Stop and
End. Use the File, Edit, View, Project, Generate, Effect and Analyze menus to Save, Export, and edit the music.
1. Click the (
) button to skip to start;
2. Adjust the output volume;
3. Click the (
) button to play;
4. Click the (
) button to record;
5. Click the (
) button to pause the recording;
6. Click the (
) button to stop the recording;
7. Adjust the input volume;
8. Click the (
) button to skip to end;
19
AUDACITY PREFERENCES
1. Click “Edit” on the Audacity interface, select “Preferences”.
The screen will show the Audacity Preferences. You can see Audio I/O, Quality, File Formats, Spectrograms,
Directories, Interface, Keyboard and Mouse in the Audacity preference interface.
2. Select the recording device: microphone (USB Audio CODEC)
• Click“AudioI/O”intheAudacityPreferencesinterface.
• Click“Device”andselect“microphone(USBAudioCODEC)”.
• Click“Channels”andselect2(stereo).
• Tickthecheckboxesbelow“Channels”.
• Click“OK”.
Note: If you cannot find the “microphone (USB Audio CODEC)” from the Device list, close the Audacity
Software, re-open it, then try again.
20
3. Adjust the output and input volume.
Output Volume Input Volume
NOTE: Because of the variations in the different operating systems, the input volume control may not
work on some individual Windows versions. Windows Vista is recommended to ensure the input volume
control is working properly.
For further details regarding Audacity recording and editing details for PC, Audacity’s home page offers a
series of references. To access these materials go to www.audacity.sourceforge.net, click on the “Help” &
“Contact Us” tabs and refer to the items highlighted as Tutorial, Tips and Wiki.
RECORDING OPERATION
To download music from PHONO to your computer:
1. Select the PHONO function and place the record on the turntable.
2. Move the tone arm over the record to start playing.
3. Click the Record (
) button to start recording.
The waves (left and right tracks) will appear on the interface.
4. At the end of the song, click the “Pause” (
) button on Audacity, then lift and move the tone arm to the
tone arm rest.
For the next song, replace the album or move the tone arm to another desired song. Immediately press
the “Pause” (
) button on Audacity and downloading will continue.
5. Repeat steps 3 and 4 until you have finished downloading.
NOTE: Do not click the “Stop” button on the computer while continuously downloading songs. Remember
to click the “Pause” button in between your desired songs. Press the “Stop” button on the computer only
when all your desired songs have been downloaded.
Afteryourhavenisheddownloading,youmayplaybackthesongsthroughyourcomputer.InStopmode,
simply click the (
) SKIP TO START button then the ( ) PLAY button.
21
To download music from Radio (FM) to your computer:
1. Press the FUNCTION button repeatedly until the TUNER function is selected, then press the
STOP/BAND button to select FM.
You may select the AM band, but the recording quality may be affected by the poor AM reception.
Tune to your desired station.
2. Press the
or
button to tune to a radio station.
3. Click the Record (
) button to start recording.
The waves (left and right tracks) will appear on the interface.
4. At the end of the program, click the “Pause” (
) button on Audacity.
5. To tune to a different station, press the
or
button on the appliance to tune to another station.
Immediately press the “Pause” (
) button on Audacity and downloading will continue.
6. Repeat steps 4 and 5 until you have finished downloading.
NOTE: Do not click the stop button on the computer while continuously downloading songs. Remember
to click the pause button in between your desired songs. Press the stop button on the computer only
when all your desired songs have been downloaded.
Afteryourhavenisheddownloading,youmayplaybackthesongsthroughyourcomputer.Instopmode,
simply click the (
) SKIP TO START button then the ( ) PLAY button.
To download music from a USB device or CARD to your computer:
1. Press the FUNCTION button to select USB (or CARD if desired).
2. Press the PLAY button to play the music.
3. Click the Record (
) button to start recording.
The waves (left and right tracks) will appear on the interface.
4. At the end of the song, click the “Pause” (
) button on Audacity.
Press the
or
button on the appliance to skip to the next song, immediately press the
“Pause” (
) button on Audacity and downloading will continue.
5. Repeat steps 3 and 4 until you have finished downloading.
NOTE: Do not click the stop button on the computer while continuously downloading songs. Remember
to click the pause button in between your desired songs. Press the stop button on the computer only
when all your desired songs have been downloaded.
Afteryourhavenisheddownloading,youmayplaybackthesongsthroughyourcomputer.Instopmode,
simply click the (
) SKIP TO START button then the ( ) PLAY button.
22
GENERAL PROBLEMS FOR ALL WINDOWS VERSIONS
1. When the turntable is connected, you cannot hear any sound if you want to listen to video or music.
It is because the default playback device has been changed to USB Audio CODEC once the turntable
connects to the PC.
Solution1: Remove the USB cable from the PC.
Solution2:
Vista and Windows 7:
Click “Start” and go to the Control Panel. Find and click the “Sound” icon. Click the “Playback” tab and
change the playback device. Click ok.
(Vista and Windows 7) (Other versions)
Other versions (e.g.: Windows XP):
- You may click “Start” and find “Programs”, “Accessories”, “Entertainment: and click “Sound Recorder”.
Then in the Sound Recorder, click the “Edit” tab and select “Audio Properties”.
- OR, find and click Control Panel. Find and select “Sound and audio device” and choose the “Audio”
tab.
In Sound playback, change the default device by clicking on the dropdown list . Select your playback
device and click OK.
Then the sound should come out.
• Pleasenotethatifyouselectsolution2,youneedtochangethesettingmanuallyeverytimeyou
connect the USB cable with the PC.
23
2. If you want to hear the music while downloading to the computer, follow steps below:
Go to the Audacity interface.
Click Edit and select “Preference”. Then click the “Audio I/O” tab.
Follow the setting below. Click “OK” to confirm.
Deselect the check box to disable the function.
ADJUSTMENT FOR WINDOWS 7 AND SOME VISTA SYSTEMS ONLY
IfyoudonothavetheuctuantwaveontheAudacityinterfaceorifthesoundisdistortedwhenrecording,
adjust the recording level as follows:
• Click“Start”atthelowerleftcorner,gototheControlPanel.
24
• InClassicView,doubleclicktheSoundicon.
• OrinControlPanelHomeview,click“HardwareandSound”.Thenclick“Sound”.
25
• IntheSoundinterface,selectthe“Recording”tab.
• Then,choosearecordingdevice.HereinwerecommendyoutoselectMicrophoneofUSBAudio
CODEC which is highlighted in the picture and click “Properties”.
• Select“Levels”andadjusttheVolumeReading.Thereadingisfrom0to100.Normallyitshouldbe
3-6. However, you may refer to the Input Level Indicator from the Audacity panel that doesn’t exceed
0. Then click “OK” on the Microphone properties interface and Sound interface. Close the Control
Panel. (Please note that there is no “Levels” tab in the “Sound” panel in some operating systems,
such as Windows 2000. For Windows 7 users and Vista users, the “Levels” tab in the “Sound” panel
is available.)
26
Input Level indicator
• Youaredownloadingmusiconyourcomputernow.Butthemusicneedstobesavedandconverted
to WAV, Ogg, or MP3 formats before exporting.
• Youmayplaybackthesongthroughyourcomputer.
• Simplyclickthe(
) button to play then turn on your computer speaker
NOTE: You may visit the Audacity office website for more detailed information and operation, etc.
PREPARING TO EXPORT AND SAVE FOR MP3 FORMAT
Prepare for MP3 Export--- (Additional software “lame_enc.dll” needs to be installed.)
1. Please make sure that the Audacity disc is still inserted in your computer.
2. Click the “Edit” tab on the Audacity interface, select “Preferences”.
27
3. Select the File Formats tab and click on the Find Library button.
4. A dialog box will appear. Click “Yes”.
5. Another box appears to locate the “CD ROM”. You will find the “lame_enc.dll” software. Click on the
software then click Open.
28
6. Click on the OK button.
Now the MP3 software set up is complete and you may proceed with exporting to MP3 format.
DIVIDING TRACKS
1. Press the ( ) button to return to the beginning of the first song.
2. Move the cursor to the wave graphic area, left click the mouse and hold then drag from left to right.
Release the mouse when the highlight reaches the end of the first song.
Highlight
3. Click the “File” tab then select “EXPORT SELECTION AS MP3”.
4. The window will pop up in a dialog box for you to provide the song title (“File name”), where you want to
save it (“Save in”), and the file format (“Save as type”).
5. Click “Save” and the first song is saved on the computer.
See the interface example below, saved as MP3 format:
29
Completed box below:
Second song to be divided and saved:
1. Move the cursor to the wave graphic at the beginning of the second song. Left click the mouse, hold and
drag from left to right until you reach the end of the second song.
2. Click the “File” tab then select “EXPORT SELECTION as MP3”.
3. Follow the steps above to divide the songs one-by-one.
TO CHANGE THE TITLES (FOR MP3 FORMAT ONLY)
DURING EXPORT SELECTION AS MP3: the software only provides one chance to give a title to the song
being saved. All subsequent songs being divided from the same track will have the same title.
1. To change the titles, follow the steps below:
1. Right click on the Music file which will show all its contents.
2. Select Properties, then click on Summary.
3. Click on Title, and then change it to your desired title.
4. Select OK.
5. Do all these steps until you have given a title to each song.
30
EXPORT AND SAVE FOR WAV AND OGG FORMATS
(AFTER RECORDING IS COMPLETE)
Whenthesongisnished,clickthe( ) button on Audacity. Then lift and move the tone arm to the tone arm
rest.
1. Highlight the song which you want to save, and then click the File tab on the Audacity interface.
2. Select “Export Selection as WAV” or “Export Selection as Ogg”.
To Export Selection as WAV
To Export Selection as Ogg
31
3. Once you have chosen which file format recording should be exported to, the interface below appears.
Here you may provide the file name and the location where it will be saved, i.e. on the desktop.
Then click “Save”.
Save as WAV
Save as Ogg
Note: You have an option to save all the songs into one file all at once. After the download is completed,
click the File tab and select Export as MP3, Export as WAV or Export as OGG.
COPYING THE MUSIC FILE TO AN MP3 PLAYER
1. Connect the MP3 player to your computer via a USB cable.
2. Turn on your computer.
3. Double click on “MY COMPUTER”.
4. Locate the drive named “REMOVABLE DISK” or “MP3 PLAYER” – This is your MP3 player.
5. Double click “REMOVABLE DISK/MP3 PLAYER” – This opens the folder. It will show all files that are
currently on your player.
6. Next, locate the music files on your computer. Most people store them in their “MY MUSIC” folder.
7. Once your music folder/MP3 file folder is open, click once to highlight the song you want to send to your
MP3 player. One of the following steps will copy the MP3 file:
A. Right click on the highlighted song and a box will appear. Move the cursor to “SEND TO” and another
box will appear. If you have the option “REMOVABLE DISK”, click on it. This will send a copy of the
MP3 file to the MP3 player.
B. If you do not have “REMOVABLE DISK” listed, click on “COPY”. Go back and repeat steps 3, 4 & 5
(above). Right click in the middle of the window and a box will appear. Select “PASTE” and the MP3
file that will be sent to the MP3 player.
32
AUDACITY FOR MAC
1. Please insert the Audacity Software disk that comes with your unit. Click on the Audacity disk on the
desktop.
2. There are five folders in the Audacity disk. Select Audacity_for_MAC for Macintosh system, and select
Audacity_for_WIN for Windows system.
• IfyourcomputerisMacOSXsystem(IntelCPU),pleaseentertheIntelfoldertoinstalltheAudacity
Software;
• IfyourcomputerisMacOS9system,pleaseentertheMacOS9foldertoinstalltheAudacity
Software;
• IfyourcomputerisMacOSXsystem(PowerPCCPU),pleaseenterthePPCfoldertoinstallthe
Audacity Software.
3. Double click on the setup file according to your supported system, for instance, the “audacity.dmg” icon
in the software files will now open in a folder. Select all the files in the folder and drag them to a suitable
location on the hard drive (Applications, etc.).
4. Double click on the Audacity icon to start running the software, alternatively, drag the “orange ball
wearing headphones” icon down to the desktop toolbar. Click on this icon to run Audacity.
CONFIGURING AUDACITY FOR MAC
Audacity Interface for Mac
33
Audacity Interface---Settings and controls.
At the top of the main Audacity window, to the right of the play control buttons, you will see the input and
output level meters (labeled L and R). Under the output level meter is an icon that looks like a microphone.
Next to the microphone is a black arrow that points downwards. Click this arrow and select Start Monitor.
(If you don’t see the input and output level meters, open your Preferences again as described above.)
Audacity Control Buttons
Use the attribute controls button at the top of the screen to go to the beginning, Play, Record, Pause, Stop and
End. Use the File, Edit, View, Project, Generate, Effect and Analyze menus to Save, Export, and edit the music.
1. Click the (
) button to skip to start;
2. Click the (
) button to play;
3. Click the (
) button to record;
4. Click the (
) button to pause the recording;
5. Click the (
) button to stop the recording;
6. Click the (
) button to skip to end;
7. Adjust the output volume.
8. Adjust the input volume.
AUDACITY PREFERENCES
1. Click “Audacity” on the Audacity interface, select “Preferences”.
The screen will show the Audacity Preferences. You can see Audio I/O, Quality, Import/Export, Interface,
Spectrograms, Directories, Smart Recording, Theme, Keyboard and Mouse.
34
2. Select the recording device: Core Audio (USB Audio CODEC)
• Click“AudioI/O”intheAudacityPreferencesinterface.
• Click“Device”andselect“CoreAudio(USBAudioCODEC)”.
• Click“Channels”andselect2(stereo).
• Click“OK”.
Note:Ifyoucannotndthe“CoreAudio(USBAudioCODEC)”fromtheDevicelist,closetheAudacity
Software, re-open it, then try again, or ensure the turntable is connected to the computer.
35
3. Under the Quality tab, set the Default Sample Format to 16 bit. Select OK to save your setting and close
the preferences window.
TO SET THE SMART RECORDING
1. To select the Smart Recording in the Audacity Preferences interface, set the Sound Activation Level (dB)
to -36 and then click OK.
2. At the top of the main Audacity window, to the right of the input and output level meters (labeled L and
R), you will see the input and output volume. To the left of the input and output volume, there is a volume
icon. Adjust the output and input volume to maximum.
Output volume Input volume
NOTE: Because of the variations in the different operating systems, the input volume control may not
work on some individual Windows versions. Windows Vista is recommended to ensure the input volume
control is working properly.
For further details regarding Audacity recording and editing details for Mac, Audacity’s home page offers a
series of references. To access these materials go to www.audacity.sourceforge.net, click on the “Help” &
“Contact Us” tabs and refer to the items highlighted as Tutorial, Tips and Wiki.
35

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Konig-Electronic-HAV-TT25USB

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Konig Electronic HAV-TT25USB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Konig Electronic HAV-TT25USB in de taal/talen: Engels als bijlage per email.

De handleiding is 7,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Konig Electronic HAV-TT25USB

Konig Electronic HAV-TT25USB Snelstart handleiding - Nederlands, Deutsch, English, Français, Italiano, Espanõl, Svenska, Suomi - 30 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info