625968
215
Verklein
Vergroot
Pagina terug
1/226
Pagina verder
MACHINE CONFIGURATION FOR THE INSTALLATION OF ATTACHMENTS
213
6.2.2 HYDRAULIC CIRCUIT
6.2.2.1 INSTALLING AND CONNECTING THE EQUIPMENT
WARNING
q The machine must be parked on a level surface, with the equipment resting on the ground.
q When the connecting pins are removed or installed, chips may come off; always wear gloves, safety
goggles and helmet.
q The change of the equipment must be carried out by two operators, who must decide together the words
and signals to be used during work.
q Avoid using your fingers to align the holes, since the may be injured or even cut off.
q Before carrying out any operation on the hydraulic circuit, stop the engine and completely drain the
residual pressure from the pipes.
For the installation of the equipment it is necessary to connect the
mechanical constraints of the bucket as described in "3.3.14
CHANGING THE BUCKET" and to carry out the hydraulic
connections using the pipes provided.
After connecting the mechanical constraints, carry out the
hydraulic connections by proceeding as follows:
1. Stop the engine and move the hydraulic controls in all
directions, in order to release the residual pressures present
in the circuits of the machine.
2. Press the optional equipment control pedal to release the
residual pressure from the delivery pipe.
3. Slowly loosen the hydraulic oil filling cap, in such a way as to
release the residual pressure from the tank.
4. Remove the plugs of the quick couplers of both the machine
and the equipment.
5. Connect the right (1) and left (2) pipes.
CAUTION
q When connecting the pipes, pay the utmost attention, in
order to prevent any impurities from getting into them, then
extend the bucket completely to avoid any interference
with the lever (A).
6. Start the machine and perform several manoeuvres with the
equipment control pedal, in order to check the seals.
WARNING
q Wear thick gloves and safety goggles during this check.
q To check the system for leakages, use a piece of cardboard
or a wooden board.
6.2.2.2 MAINTENANCE
The hydraulic system does not require any operation and
inspection other than those prescribed for the routine
maintenance of the machine. Regarding the maintenance
operations required for the equipment, see the specific operation
manuals.
RWA07960
2
1/2" GAS
1/2" GAS
1
SX
DX
RKA14350
1
2
215

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Komatsu Galeo PC14R-2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Komatsu Galeo PC14R-2 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info