782842
28
Verklein
Vergroot
Pagina terug
1/39
Pagina verder
28
English
Installation
Note:
The washer-dryer is equipped with power
cord and plug and needs sewage and
tap water connections. Make sure before
installation that a suitable wall outlet,
sewage and tap water connection are
available at the desired place of installation.
Consider the dimensions (chapter Technical
data) of the product for placing and
installation.
Caution
Before initial operation the transport
restraints must be removed from the
backside of the unit. Operating the
washer-dryer with mounted transport
restraints leads to serious damages.
Keep the transport restraints for later
use. Never transport the device without
correctly mounted transport restraints!
Fig. 1Loosen the four transport restraints
with a wrench (13 mm) and unscrew
them completely. Then insert the 4
supplied blind plugs in the holes.
Fig. 2Place the appliance on an even,
horizontal and steady surface. For
levelling the feet are adjustable and can
be screwed in or out.
Unscrew the lock nuts with an open-
end wrench (17 mm).
Turn the feet to the right to screw
them in and to the left to unscrew
them.
Use a spirit level to check
whether the appliance is leveled.
If the appliance is not standing
horizontally or is tilting the feet
must be adjusted again.
If the unit is leveled and does not
tilt, tighten the lock nuts with the
open-end wrench.
Note:
Note the following, when placing the
appliance on a platform:
The appliance might move during spinning
and could fall of a platform. To prevent this,
the feet must be secured with retaining tabs
(available in specialized stores).
Fig. 3The washer-dryer must be connected
to a drain.
The drain hose is already fixed to the
sewage connection. Pull the hose
out of the clamps and unwind it.
Connect the other end to the
drainpipe (Option B, hose end at
least 60cm high) or place the end
of the hose in a sink or washbasin
(Option A, end of hose at a maximum
height of 100cm).
Note:
Suitable hose holders are available as
optional accessories.
Fig. 4Connect the water inlet to the water
system (3/4“) using the supplied hose
and make sure that everything is
connected correctly and firmly. The
water pressure must be between
0.05MPa and 1 MPa. A pressure
reducing valve must be used if the
water pressure is exceeds 1 MPa.
Note:
If the water pipes are new or have not
been used for an extended period of time,
allow a certain amount of water to drain
until you are sure that the water is clear
and free of foreign objects.
If this point is not observed, there is a risk
that the water inlet will become clogged
and the unit will be damaged.
The sewage and tap water connection
must be checked on a regular basis.
Fig. 5Plug the mains plug into a suitable
socket.
IM_KWDR 8632 B INV_211029_V08_HR.indb 28IM_KWDR 8632 B INV_211029_V08_HR.indb 28 29/10/2021 10:10 AM29/10/2021 10:10 AM
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Koenic KWDR 8632 B INV bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Koenic KWDR 8632 B INV in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 3.7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info