Handleiding Koenic KRVC 2320 RC (pagina 25 van 148) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Zweeds)

782606

Verklein

Vergroot

Pagina terug

1/148

Pagina verder

English

Fig. 20 Remove the mop cover from the water

tank and wash it with a little detergent

and rinse it o. Wring the mop cover

slightly and let it dry.

Fig. 21 Attach the mop cover in the correct

position on the water tank. A

replacement mop cover is included.

Recommendations for a better

cleaning result

Vacuuming

• Before starting the vacuuming process,

remove all objects that stand/ lay on the

ﬂoor, which could interfere with the process

or in which the robot could get tangled up

(e.g. toys, carpets with longer cords etc.).

• Make sure that no objects hang down onto

the ﬂoor, in which the robot could get stuck

(e.g. power supply cables, curtains etc.).

• If possible, place chairs on the table during

the vacuuming process, in order to minimize

the number of obstacles on the ﬂoor.

• Block areas, in which the robot could get

stuck (e.g. closets with lowered boards,

tapered areas in between closets etc.).

• Make sure that all brushes can rotate freely

and aren’t blocked. Clean them if necessary.

• Empty the dust container.

Swabbing

• Observe all recommendations listed above.

• Have the robot vacuum the area before

swabbing, in order to reduce the amount of

dust on the ﬂoor.

• Soak the cleaning cloth under running water

and slightly wring it out, before attaching it

to the water tank, to enhance the cleaning

result and to achieve an equal distribution

of water onto the ﬂoor.

• If necessary, pause the swabbing process

and manually wring out the cleaning cloth,

removing bigger particles, before continuing

the process.

Fig. 25 Close the dust collector again and

insert it into the vacuum cleaner. Make

sure it is assembled properly.

Warning

Never use the device without a ﬁlter

Note:

• The two rotating brushes are subject to a

certain amount of wear, depending on the

type of hard ﬂoors you have (e.g. rough,

rustic tiles). Therefore, you must check

them at regular intervals to ensure, that

they’re undamaged.

• Worn rotating brushes may have sharp

edges that can damage sensitive hard

ﬂoors, such as parquet or linoleum.

The Imtron GmbH does not accept any

responsibility for damage caused by worn

brushes

Fig. 26 If the brush roller is blocked by or full

with hair, lint or similar residues remove

and clean it. Press the buttons on the

cap, remove the cap and then remove

the brush roller. Remove hair and

lint, etc. by hand or with a brush. The

assembly takes place in reverse order.

Cleaning and care

Warning

• When cleaning, never use solvents or

abrasive materials, hard brushes, metallic

or sharp objects. Solvents are harmful to

human health and can attack plastic parts,

while abrasive cleaning mechanisms and

tools may scratch the surface(s).

• Never immerse any electrical part of the

product in water or in other liquids during

cleaning. Never place it under running

water.

• Before cleaning, always switch o the

vacuum robot and disconnect the plug of

the charging base from the power supply.

Emptying dust container and cleaning

ﬁlters and mop cover

Note: The dust container should be emptied

every time after vacuuming.

Fig. 22 After vacuuming, remove the dust

container. Press the release button and

pull it out.

Fig. 23 Hold the dust container over a dust bin,

so that the opening with the yellow

ﬂap faces upwards. This way, the dust

will fall downwards, when opening the

container.

Fig. 24 After approx. 3 operating hours, but

at the latest when the performance

decreases, clean the dust pre-ﬁlter, ﬁne

ﬁlter and HEPA ﬁlter. To do this, remove

all ﬁlter components and clean them

separately. The assembly is done in

reverse order. Make sure, that the ﬁlter

insert is correctly assembled. To ensure

this, press the shorter side wall into the

ﬁtting ﬁrst, before pushing in the ﬁlter

on the other sides by pressing down on

the edges.

IM_KRVC2320RC_190807_V10_HR.indb 25 7/8/2019 14:43

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Koenic KRVC 2320 RC Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info