584806
6
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
Page 10 Page 11
Connecting the Loudspeakers - 4Connecting the Loudspeakers - 3
Bi-amping and Tri-amping
Connecting each loudspeaker drive element to separate amplication oers the highest possible performance
level. It is not necessary for the ampliers in the treble and bass sections to be identical. In fact for tube ampli-
er enthusiasts, there are advantages to using smaller ampliers in the treble and midrange sections as the
smaller transformers oer the signicant possibility of extended, sweeter treble response.
To multi-amp, the following criteria are essential:
The ampliers should be phase coherent. In other words, all ampliers should be, by design, phase non-invert-
ing or phase inverting, or if not, should be connected so as to be all phase non-inverting or phase inverting.
The ampliers must have identical voltage gains, or should be set up to have identical voltage gains.
The ampliers must have low residual noise characteristics, especially in the midrange and treble sections.
Ampliers in corresponding channels must be identical; i.e., both bass ampliers must be the same and so on.
If any of the above conditions are not met, separate amplication will be signicantly worse than ordinary
bi- or tri-wiring. If you are unsure about these concepts or unsure if your ampliers meet these criteria, it is es-
sential that you consult your Klipsch specialist dealer before proceeding further.
Bi-amping
The Mid/Treble amplier is bi-wired
(One channel shown)
Important Note. After connecting and placing the loudspeaker upright, the connections will be hidden from
view. We strongly recommend that you identify each cable to eliminate possible diculties down the line.
Bi-wiring
Bi-wiring reduces unwanted interactions between the bass drivers and the midrange and treble units.
True bi-wiring is connecting separate cables from the bass terminals and the midrange/treble terminals to a
common connection at the amplier. Several cable manufacturers produce specialized cables where one cable
jacket contains four cables, thus enabling bi-wiring within one cable cluster. This eliminates the need to run
separate cables and simplies connection. In any case, the method of connection is the same.
Prepare the crossover panel as shown on the previous page. Proceed as for standard wiring, but connect one
cable to the bass terminals of the speaker. Connect a second cable to the midrange and treble terminals. Refer
to the diagram. After connection, tighten all the terminals with the supplied wrench as shown previously.
HFHF
MFMF
LFLF
LFLF
HFHF
MFMF
Right Speaker Left Speaker
AMPLIFIER
Tri-wiring
The logical extension to bi-wiring is tri-wiring, where all the elements of the loudspeaker are separately con-
nected to the amplier.
To tri-wire, you need to remove all the straps connecting the terminal pairs and then connect three cables as shown
in the diagram below. After connection, tighten all the terminals with the supplied wrench as shown previously.
HFHF
MFMF
LFLF
HFHF
MFMF
LFLF
Right Speaker Left Speaker
AMPLIFIER
Important Note. After connecting and placing the loudspeaker upright, the connections will be hidden from
view. We strongly recommend that you identify each cable to eliminate possible diculties down the line.
HFHF
MFMF
LFLF
HFHF
MFMF
LFLF
Tri-amping
(One channel shown)
MID /
TREBLE
AMP
BASS
AMP
TREBLE
AMP
MID
AMP
BASS
AMP
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Klipsch P-39F bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Klipsch P-39F in de taal/talen: Engels als bijlage per email.

De handleiding is 1,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Klipsch P-39F

Klipsch P-39F Gebruiksaanwijzing - Espanõl - 100 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info