584802
9
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
MAIN SPEAKERS FULL RANGE
Connect the subwoofers left and right channel “LINE IN” jacks to a non-filtered (full-range) main
channel, pre-amp output on your receiver or pre-amp/processor. Refer to the lefthand side of Figure A.
This signal contains the normal bass information present in the main left and right channels. When
connecting to a component that has only a single pair of pre-amp outputs, “Y” adapters (splitters)
may be used to feed a signal to both the subwoofer and the power amplifier.
Note: When connecting to a mono subwoofer output on your electronics (preferably full range), add
a “Y” cord to the subwoofer end of the cable and connect to both line inputs. This will provide a sig-
nificant increase in the subwoofers output level when compared to the connection of just one of the
“LINE IN” inputs.
MAIN SPEAKERS LIMITED RANGE
If a bass limited (high pass filtered) signal is to be sent to your main speakers, connect your main
channel power amplifier inputs to the “LINE OUT” jacks on the subwoofer. Refer to the lefthand
side of Figure B. These outputs will remove frequencies below 50 or 100Hz from your main speakers,
depending upon the setting of the “HIGH PASS SELECT” switch. This type of hookup reduces dis-
tortion and increases the dynamic range of your main amplifier and speakers.
LFE/BYPASS IN (optional)
This input is used with 5.1 (six channel) surround sound systems. The LFE channel contains bass effects
information that is different than the bass signals present in the other channels to enhance the sound-
track’s impact. Connect the “LFE/BYPASS IN” input on the LF-10 and LF-12 to your electronic’s desig-
nated LFE output jack. The “LFE/BYPASS IN” requires a low pass filtered signal from your electronics
(high frequencies removed). Do not connect this input to a full range (unfiltered) pre-amp output.
Note: The peak level of this signal can be up to 10 decibels louder than main channel bass signals, so
caution should be exercised when connecting to this output and initially adjusting the subwoofers
“LFE LEVEL” control. Signals coming into this jack are not affected by the subwoofers adjustable
“LOW PASS (Hz)” filter or main “LEVEL” control. The “LFE/BYPASS IN” will not normally be the
only connection to the subwoofer, unless the LFE channel is the only signal the subwoofer will be
reproducing. The “SPEAKER IN” and “LINE IN” connections are the primary hookups. The “LFE
IN” is compatible with either line level or speaker level connections.
BASS MANAGEMENT
Most surround sound electronics are equipped with a bass management system that permits the selection
of either a full or limited range (bass filtered) operation for each speaker. When using the “LINE IN” or
“SPEAKER IN” connections on the subwoofer, configure the main channels of your surround electronics
for the “Large” or “Full Range” setting. When connecting to a subwoofer output, defeat the low pass
ltering on your electronics, if possible. If this cannot be done, use the “LFE/BYPASS IN” input and let
your electronics determine the low pass frequency for the subwoofer (the “LFE LEVEL” control now
becomes the primary subwoofer level control). Alternately, you can connect the subwoofers “LINE IN”
input to a subwoofer output and set the “LOW PASS (Hz)” control on the subwoofer to a lower cutoff
frequency if desired. Since the specifics of bass management systems vary from brand to brand, consult
your Klipsch dealer or the manufacturer of your electronics for more details.
Operating Controls
LEVEL
This control adjusts the volume of the subwoofer relative to your main speakers. Use this control to
compensate for room acoustics, subwoofer placement and the sensitivity of your main speakers. This
control affects the signals that are connected to the “LINE IN” or “SPEAKER IN” inputs. It does not
affect the volume level of your main speakers or signals connected to the “LFE/BYPASS IN.
Suggested control position for initial setup: 10 o’clock.
!
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Klipsch LF-10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Klipsch LF-10 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info