Handleiding Klipsch Heritage (pagina 5 van 37) (Duits, Engels, Frans, Italiaans, Portugees, Spaans)

584715

Verklein

Vergroot

Pagina terug

1/37

Pagina verder

place it on top of the low frequency cabinet while placing the

low frequency cable toward the rear and out the gap between

the cabinets. Align the recesses on the bottom surface of the

high frequency cabinet with the rubber bumpers on the top of

the low frequency cabinet. Connect the low frequency cable to

the two screw barrier strip on the rear of the low frequency

cabinet. Be sure to observe proper polarity by connecting the

wire with the Red Indicator to the terminal with the Red mark-

ing and the wire with the Black indicator to the other terminal.

PLACEMENT

Your Klipsch Heritage loudspeakers will perform well in a

variety of locations but best results will be achieved using the

following general guidelines:

• All: Place on a common wall 6 to 15 feet apart.

• La Scala, Cornwall, Heresy: Position them equidistant from

the wall behind the speakers.

• Heresy: Equidistant height above the floor with the high

frequency drivers at seated ear height if wall or cabinet

mounted.

• All: Angle speakers toward the listener and even with or

forward of any adjacent obstructions.

• La Scala, Cornwall, Heresy: Placing them near a corner or

wall provides the greatest amount of bass while moving the

speakers away from room boundaries reduces bass energy.

• All: Asymmetrical placement of a pair of speakers from

adjacent side walls can smooth room-induced bass

unevenness.

• Experiment with the above guidelines to suit your taste and

to compensate for your room's acoustic characteristics.

Klipschorn

Klipschorn speakers typically perform best when positioned in

the corners on the long wall of a rectangular room. If the room

is very narrow and long with corners farther apart than 18 to

20 feet, the stereo image may not be optimal. A room with a

length to width ratio of 1.00 to .618 is preferred. In addition,

Klipschorn loudspeakers seem to benefit from ceiling heights

no lower than 8.5 feet. The Klipschorn requires corner place-

ment because the walls of the room serve to complete the

speaker’s low frequency horn. To achieve full low frequency

extension, the Klipschorn should fit tightly in a corner without

baseboard or trim interference and the wall surfaces should

extend at least 25 inches beyond the side grilles.

False Corners

If proper corners are not available in your listening room, false

corners can be constructed to yield bass performance similar

to a full corner and also allow for some adjustment of toe-in if

desired. Start with a 2’ x 4’ framework as shown in Figure 3.

Klipsch recommends using standard 4 foot wide sheets of

3/4” plywood securely glued and nailed to the framework. The

backside may be covered with a thinner material such as

3/16” masonite or 1/2” plywood. Paint to match wall color, or

finish with a laminate or other material. (See Figure 3.) In the

case of very wide spacing, a false corner can be employed on

one of the Klipschorns to reduce the distance between speak-

ers. Another solution to widely spaced Klipschorn loudspeakers

in an audio only system is the addition of a center speaker

such as the La Scala to create a three-speaker stereo array.

Please contact Klipsch Technical Support at 1-800-554-7724

for connection details.

La Scala II

The La Scala II features a self-contained, front-firing, folded

bass horn to permit placement out of the corner if required.

However, because this model has less bass extension than the

Klipschorn, the low-frequency acoustic reinforcement of corner

placement may be optimal. The La Scala also offers full flexi-

bility with regard to the amount of toe-in for the desired stereo

image. Deep bass performance may also be augmented with a

high performance Klipsch subwoofer.

Cornwall III

The Cornwall III offers the placement and toe-in flexibility of

the La Scala with low frequency extension similar to the

Klipschorn at a reduced output capability. As with the La Scala

and Heresy, corner positioning yields the greatest amount of

bass output while placements out of the corner or away from

rear walls will yield less bass. Since room acoustics and

personal taste vary we recommend experimenting with several

locations to fine tune the speaker’s performance. Self-stick

rubber pads are supplied for attachment to the bottom of the

riser for use on hard floors.

Heresy III

The Heresy III offers the greatest degree of placement flexibili-

ty of all of the Heritage models due to its relatively compact

size. It delivers the same basic frequency range as the La

Scala but at more modest output levels. Corner, floor place-

ment will deliver the highest degree of low bass reinforcement

and the slant riser base helps to compensate for the Heresy’s

short stature. This riser may be removed for shelf or cabinet

placement. Self-stick rubber pads are supplied for attachment

to the bottom of the cabinet to prevent scratching of shelves

and hard surfaces.

CONNECTING YOUR LOUDSPEAKER

Caution: Turn your amplifier off before making any

connections! (See Figure 4.)

• Your loudspeakers are equipped with positive (Red) and

negative (Black) connection terminals, on the rear or side

of the cabinet. These correspond to the positive and

negative terminals on the appropriate channel (left, right,

etc.) of your amplifier and will accomodate bare wire,

spade lugs or banana plugs (See Figure 4).

• All speakers in your system must be connected in phase

with the positive speaker terminal connected to the positive

amplifier terminal. Repeat this for the negative

speaker and amplifier terminals. Most speaker wire has

distinguishing markings on the insulation of one of the

conductors to assist in correct hookup.

• Use 16-gauge (AWG), two conductor, copper wire at a

minimum and larger gauge wire for longer runs. The

connection terminals on your loudspeaker will accommo

date bare wire, spade terminals or banana type plugs.

•

Caution: With all connection types take care that there is

no contact between the positive and negative terminals at

the speaker and amplifier. Damage to your equipment

may result! (See Figure 4.)

Klipsch Heritage Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info