742264
2
Verklein
Vergroot
Pagina terug
1/3
Pagina verder
EN
Introduction
Through the use of trailing edge, it is possible to dim
the connected load with this dimmer without noise.
This dimmer is equipped with a fine fuse and tem-
perature fuse. If overloaded the dimmer will reset
automatically after the cooling-off period. The cause
of the overload should be reviewed and fixed as soon
as possible. The dimmer is electronically protected
against short circuit and overload. In the event of a
short-circuit or a long-term overload, the fuse in the
dimmer will be permanently activated.
Waranty: 24 months if the product has been used ac-
cording to the instructions and has not been opened.
User manual for Klemko LED dimmer, trailing edge
receivers for electronic transformers.
891042 D-PAF-200-LED
891042 D-PAF-200-LED
These dimmers can become hot when in operation.
The consequence of because a part of the connected
load (the losses) turns into heat. The rated power
output of the dimmer only applies to installations in
a massive stone wall. If the dimmer is installed in a
wall of aerated concrete blocks, wood, plaster, or a
build-up edge, the maximum connected load must
be reduced by a min. of 20%. This is also neces-
sary when there are multiple dimmers installed in a
combination. (NEVER MAKE A VERTICAL COMBINATION
WITH MULTIPLE DIMMERS!). The same counts when
there is an extreme heat source nearby the dimmer.
Heat
Connection
Disconnect power
Connect according to the wiring diagram
(Note: do not switch live wire and zero)
Secure the cover plate with the nut
if necessary, use the shaft adapter to widen the
shaft to 6mm.
Place the knob
Installation instructions
Voltage 230 Vac (+6 % / -10%)
Power 1 - 200 W
Max. led drivers 15 pcs
(multiple leds per driver possible)
Max. light sources 15 pcs
Dimming Trailing edge / RC
Change over relais Yes
Fuse circuit breaker 16A IEC/EN 60898 certified, Type B
Inrush current 1000 A / 20 µsec
Standards TÜV / CE
Specifications
This intelligent dimmer is equipped with a fine
adjustment. If your lights flash, this small button
allows you to adjust the minimum brightness.
Proceed as following:
Turn the dim shaft fully to the left. Now trim the
potentiometer with a screwdriver (see wiring di-
agram) to the desired minimum brightness.
Adjusting minimum brightness
Klemko Techniek B.V.
Nieuwegracht 26 T +31 (0)88 002 3300
NL-3763 LB Soest www.klemko.nl
the Netherlands info@klemko.nl
N
L
Driver / transformator
L L
On/Off
Minimum brightness
Turn the dim shaft fully to the left;
Now trim the potentiometer with a screwdriver
(see wiring diagram) to the desired minimum
brightness. Set the potentiometer between 5 %
and 30 %.
(Dimmable) led-lighting
(Retrofit) lightbulbs
High volt halogen 230V
Electronic transformers for trailing edge
Works with
A. Press the rotary knob: the connected lamps are
switched on or off.
B. Turn the rotary knob either clockwise or coun-
ter-clockwise.
The connected lamps are dimmed brighter or
darker.
Warning:
each terminal
pin connects
to one wire
only
DANGER
Risk of serious damage to property and per-
sonal injury, e.g. from fire or electric shock,
due to incorrect electrical installation.
The outputs may carry an electrical current even
when the device is switched off. Always disconnect
the fuse in the incoming circuit from the supply befo-
re working on connected loads.
Safe electrical installation can only be ensured if the person in
question can prove basic knowledge in the following areas:
Connecting to installation works
Connecting several electric devices
laying electric cables
These skills and experience are normally only pos-
sessed by skilled professionals who are trained in the field of
electrical installation technology.
If these minimum requirements are not met or are disregarded
in any way, you will be solely liable for any damage to property or
personal injury.
For your safety
Installation
Install the dimmer in a single, standard flush mounting box, or drill a
65,5mm diameter hole.
Changeover circuit (image. 2)
Resetting the dimmer / Preparing the dimmer for the first time (image. 3)
Installation (image. 4)
N
L
Driver / transformator
L L
Max.
Max.
When you first install the dimmer or with every ad-
justment or modification of the connected lighting,
the dimmer settings can no longer be optimal.
Resetting the dimmer:
1. Turn on the light at maximum brightness
2. Turn the smart adjustment to 5%
3. Within 2 seconds turn the smart adjustment
from 5% directly to 30% and back to 5%.
The connected light will go off and on again.
The next step is to set the minimum brightness of
the connected lights.
Preparing dimmer for first use (image. 3)
Warning: Before installation, disconnect all cables for the part of
the installation feeding the lights. Read the instructions carefully.
If in doubt, consult a certified electrical installer !!!
2

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Klemko-891042---D-PAF-200-LED

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Klemko 891042 - D-PAF 200 LED bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Klemko 891042 - D-PAF 200 LED in de taal/talen: Nederlands, Duits, Engels als bijlage per email.

De handleiding is 0,96 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info