Instructions de montage
F
Pour votre sécurité
■ L’ergomètre ne doit être utilisée que pour les fins auxquelles
elle est destinée, c'est-à-dire pour l'entraînement des adultes.
■ Tout autre emploi est interdit, voire dangereux. Le fabricant
ne pourra être rendu responsable de dommages causés par
l'emploi inadéquat de l'appareil.
■ Vous vous entraînez avec un appareil dont la technique et la
sécurité correspondent aux exigences modernes. Les sources
possibles de danger qui pourraient entraîner des blessures
ont été soit supprimées, soit sécurisées.
Lire attentivement les présentes instructions avant le montage et la première utilisation de l'appareil. Elles contiennent des renseignements
importants relatifs à la sécurité des personnes ainsi qu'à l'emploi et à l'entretien de la bicyclette d´áppartement . Conserver soigneusement
lesdites instructions pour d'éventuels renseignements ainsi que pour effectuer l'entretien de l'appareil ou commander des pièces de rechange.
Instructions for Assembly
■ Ensure that you have received all the parts required (see
check list) and that they are undamaged. Should you have
any cause for complaint, please contact your KETTLER dealer.
■ Before assembling the equipment, study the drawings
carefully and carry out the operations in the order shown by
the diagrams. The correct sequence is given in capital letters.
■ The equipment must be assembled with due care by an adult
person. If in doubt call upon the help of a second person, if
possible technically talented.
■ Please note that there is always a danger of injury when
working with tools or doing manual work. Therefore please
be careful when assembling this machine.
■ Ensure that your working area is free of possible sources of
danger, for example don’t leave any tools lying around.
Always dispose packaging material in such a way that it may
not cause any danger. There is always a risk of suffocation if
children play with plastic bags!
■ The fastening material required for each assembly step is
shown in the diagram inset. Use the fastening material exactly
as instructed. The required tools are supplied with the
equipment.
■ Bolt all the parts together loosely at first, and check that they
have been assembled correctly. Tighten the locknuts by hand
until resistance is felt, then use spanner to finally tighten nuts
completely against resistance (locking device). Then check that
all screw connections have been tightened firmly. Attention:
once locknuts have been unscrewed they no longer function
correctly (the locking device is destroyed), and must be
replaced.
■ To pull off the pedal arms remove cap and screw (A). Grip
the pedal arm tightly, and screw in an M12 bolt (not
supplied) into the thread (B). After a few turns you may take
off the pedal arm (C).
■ For technical reasons, we reserve the right to carry out preli-
minary assembly work (e.g. addition of tubing plugs).
■ Please keep original packaging of this article, so that it may
be used for transport at a later date, if necessary.
List of spare parts
When ordering spare parts, always state the full article number,
spare partnumber, the quantity required and the S/N of the
product.
Example order: Art. no. 07990-700 / spare-part no.
10100030/ 2 pieces / S/N no......
Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this should
be clearly stated on the order by adding the words „with fastening
material“.
Waste Disposal
KETTLER products are recyclable. At the end of its
useful life please dispose of this article correctly and
safely (local refuse sites).
KETTLER (GB) Ltd. · Merse Road · North Moons Moat · Redditch,
Worcestershire B98 9HL · Great Britain
KETTLER International Inc. · P. B. 2747 · Virginia Beach · VA 23450
-2747USA
http://www.kettler.net
■ Please ensure that liquids or perspiration never enter the
machine or the electronics.
■ Before use, always check all screws and plug-in connections
as well as respective safety devices fit correctly.
■ Always wear suitable shoes when using.
■ Do not use corrosive or abrasive materials to clean the
equipment. Ensure that such materials are not allowed to
pollute the environment.
■ The product is not suitable for use by persons weighing over 150
kg.
