683161
62
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Preamplifier
The preamplifier can be configured to one of the two options: low
gain type that places priority on IMD (PRE 1) and high gain type
that places priority on sensitivity (PRE 2).
Press F [ANT/PRE].
Pressing F [ANT/PRE] each time switches the selection in the
following sequence: “PRE 1” → “PRE 2” → “OFF”.
The preamplifier selection is stored for each antenna
selection band.
The default values are as follows.
Less than 7.5 MHz: OFF
7.5 MHz to less than 21.5 MHz: PRE 1
More than 21.5 MHz: PRE 2
RX Monitor
If weak signals are received while the squelch is closed, the signals
tend to be interrupted. Also, you may sometimes want to monitor
the condition of the RX frequency while in the CTCSS standby
state. In this case, the RX monitor is used to open the squelch
temporarily.
“RX Monitor” (Menu [0-15] to [0-31]) can be assigned to a PF key.
While the PF key that is assigned with “RX Monitor” is pressed and
held down, the squelch opens and the RX frequency can be
monitored. The RX monitor turns OFF once the key is released.
Scanning is paused while PF [RX Monitor] is pressed.
SWL (BCL) Mode
The SWL (BCL) mode is intended for SWL (Short Wave Listening)
and BCL (Broadcast Listening) by displaying the horizontal dial of
the “9R-59” communications receiver on the screen.
1 Press [MENU].
2 Press F [SWL] to display the SWL screen.
If F [SWL] is not displayed, press F [MORE].
.
3 Press [MENU] followed by F [SWL].
Returns to the normal screen.
Switching to the SWL mode is not possible while the
transverter is ON.
An indicator is not displayed if a memory channel that is
not registered is being called up.
Restrictions are applied to the following functions in the SWL
mode.
Function Status
Transmission Disabled
Sending of voice message Disabled
Decoding/Encoding Disabled
Sending of CW message Disabled
TX output power limiter Disabled
Meter switching Disabled
TX filter switching Disabled
Turning ON transverter Disabled
FM tone Disabled
Antenna tuning Disabled
Configuration of the TX
equalizer and related
settings
Disabled
Band Switching in the SWL Mode (VFO Mode)
Press F [BAND
]/ F [BAND ].
The “broadcast/meter band” is displayed when the
frequency falls within the band range. The preset broadcast
bands are shown in the table below.
Broadcast/
Meter Band
Lower Limit
[kHz]
Upper Limit
[kHz]
Default [kHz]/ Mode
LW 145 285 145
AM
MW 525 1705 525
120 m 2300 2495 2300
90 m 3200 3400 3200
60 m 4750 5060 4750
49 m 5900 6200 5900
41 m 7200 7450 7200
31 m 9400 9900 9400
25 m 11600 12100 11600
21 m 13570 13870 13570
19 m 15100 15800 15100
16 m 17480 17900 17480
15 m 18900 19020 18900
13 m 21450 21850 21450
11 m 25670 26100 25670
The band segments of the SWL mode that is preconfigured on
this transceiver are represented in a slightly different way
compared to conventional meter bands. Different band
segments are used so as to achieve wider coverage to include
the broadcast bands of the different regions and other bands.
5 COMMUNICATING AIDS
5-6
62

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info