606707
56
Verklein
Vergroot
Pagina terug
1/77
Pagina verder
APRS-11
SELECTING A POSITION COMMENT
Enter Menu mode and access Menu 607.
The APRS data which you transmit always includes one of the
15 predetermined position comments. Select an appropriate
comment depending on your situation.
The selectable comments are listed below:
[Off Duty] [Enroute] [In Service] [Returning] [Committed] [Special]
[PRIORITY] [CUSTOM 0 ~ CUSTOM 6] [EMERGENCY!]
If you select “Emergency!”, a confi rmation message appears. Press
the Tuning control again.
ATTENTION: When it is unnecessary, never “EMERGENCY!”. When an
emergency signal is received using APRS, the Emergency Alarm on all
stations will sound.
STORING STATUS TEXT
Enter Menu mode and access Menu 608.
Text <TEXT>
Status text is another comment to transmit with position
data. Unlike a position comment, you can make any desired
comment using a maximum of 42 alphanumeric characters.
This transceiver has 5 memory channels for preprogramming.
1 Select a status text number.
• Press [USE] to mark the currently used status text with [ ].
2 Enter your status text.
Text Transmit Frequency <TX RATE>
Select the frequency on which to transmit the status text
when the APRS beacon is transmitted. You can select [OFF],
or [1/1] ~ [1/8] (APRS only).
1/X means the status text will be transmitted X number of times.
QSY FUNCTION
The QSY function uses AFRS (Automatic Frequency Reporting
System) to report a frequency on which voice communications
can be established. A station using the QSY function embeds
the frequency information in a position beacon transmission.
A receiving station of this information can change frequency,
or QSY, over to the reported voice frequency to begin voice
communication by the select of [TUNE].
Transmitting QSY Information
A properly confi gured functioning TM-D710G QSY station can
automatically embed the voice frequency from the non-data band
to the beginning of status text. This is the mechanism used for
automatically transmitting the frequency information.
The format of the transmitted frequency is FFF.FFF MHz.
So, for example, if at the time of a beacon transmission, the
non-data band has a frequency of 446.100 MHz selected, then
the frequency of “446.100MHz” gets embedded to the beginning
of the status text. If you confi gure in any of Statuses 1 through 4
the frequency of “446.100MHz” at the beginning of the status text
messages, then this fi xed frequency will be transmitted as QSY
information along with the beacon transmission. In addition to
frequencies, there are fi elds where you can send other settings
such as Wide/Narrow, Tone/CTCSS/DCS, Shift (+/-), and Offset
frequency simply by -leaving one space between each value.
Therefore, other information besides just a frequency can be
sent.
QSY Information Format:
(Insert one space after the frequency before entering Wide/
Narrow, Tone/CTCSS/DCS and Shift/Offset.)
“T079”: An upper case “T” indicates Wide. Tone frequency of 79.7
Hz. (Encoding)
“t079”: A lower case “t” indicates Narrow. Tone frequency of 79.7 Hz.
(Encoding)
“tOFF”: A lower case “t” indicates Narrow. Tone = OFF (Without any
tone Encoding or Decoding.)
“C079”: An upper case “C” indicates Wide. CTCSS frequency of 79.7
Hz. (Encoding/ Decoding)
“c079”: A lower case “c” indicates Narrow. CTCSS frequency of 79.7
Hz. (Encoding/ Decoding)
“D023”: An upper case “D” indicates Wide. DCS code of 023.
(Encoding/ Decoding)
“d023”: A lower case “d” indicates Narrow. DCS code of 023.
(Encoding/ Decoding)
“+” : Plus Shift (A default offset frequency is applied.)
“–” : Minus Shift (A default offset frequency is applied.)
“+500” : Plus Shift, 5 MHz Offset
“–060”: Minus Shift, 600 kHz Offset
The value of the Offset shall be a 3-digit number. (x 10 kHz/ 50
kHz step)
Refer to the website for QSY Information Format:
http://aprs.org/info/freqspec.txt (as of October 2013)
56

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TM-D710GA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TM-D710GA in de taal/talen: Engels als bijlage per email.

De handleiding is 7,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TM-D710GA

Kenwood TM-D710GA Gebruiksaanwijzing - Nederlands - 75 pagina's

Kenwood TM-D710GA Gebruiksaanwijzing - Nederlands - 55 pagina's

Kenwood TM-D710GA Gebruiksaanwijzing - Deutsch - 74 pagina's

Kenwood TM-D710GA Gebruiksaanwijzing - English - 55 pagina's

Kenwood TM-D710GA Gebruiksaanwijzing - Français - 77 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info