511233
12
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
7
3 GETTING ACQUAINTED
TRANSMITTING
1 To transmit, hold the transceiver approximately
5 cm (2 inches) from your mouth, then press and
hold the PTT switch and speak into the
microphone in your normal tone of voice.
The status LED on the top panel lights red and
bar-graph meter appears.
If you press [PTT] while you are outside of the
transmission coverage, a high pitched error
beep sounds.
2 When you finish speaking, release the PTT switch.
Note: If you transmit continuously for more than 10 minutes, the
internal time-out timer generates a warning beep and the transceiver
stops transmitting. In this case, release the PTT switch and let the
transceiver cool down for a while, then press the PTT switch again to
resume transmitting {pages 40, 51}.
Selecting Output Power
Selecting lower transmission power is the best
way to reduce the battery consumption, if
communication is still reliable. You can configure
different power levels for transmission {page 41}.
Press [LOW].
Each time you press [LOW], the indicator
cycles between “H” (high), “L” (low), and “EL”
(economic low).
Note:
You can store different output power setting for the A and B-
band.
When you change the output power, it is reflected to all
available amateur bands for A or B-band.
SELECTING A FREQUENCY
VFO Mode
This is the basic mode for changing the operating
frequency. Turn the Tuning control clockwise to
increase the frequency. Turn the Tuning control
counterclockwise to decrease the frequency. Or,
press [ ]/ [ ] to change the frequency.
MHz Mode
If the desired operating frequency is far away from
the current frequency, it is quicker to use the MHz
tuning mode.
To adjust the MHz digit:
1 Press [MHz].
A MHz digit blinks.
2 Turn the Tuning control or press [ ]/ [ ] to
select the desired MHz digit.
3 After selecting the desired MHz digit, press
[MHz] to exit the mode and return to normal
VFO mode {above}.
4 You may further adjust the frequency using the
Tuning control or [ ]/ [ ].
Note: MHz mode does not function in AM band.
Direct Frequency Entry
In addition to turn the Tuning control or press
[ ]/ [ ], there is another way of selecting the
frequency. When the desired frequency is far
away from the current frequency, you can directly
enter a frequency from the numeric keypad.
1 Press [VFO].
You must be in the VFO mode to make the
direct frequency entry.
2 Press [ENT].
“– – – – – –” appears.
3 Press the numeric keys ([0] to [9]) to enter
your desired frequency. [MHz] can be used to
complete the MHz digits entry.
Pressing [ENT] fills the remaining digits (the
digits you did not enter) with 0 and
completes the entry.
To select 145.000 MHz for example, press
[1], [4], [5] then press [ENT] to complete
the entry.
If you want to revise the MHz digits only,
press [VFO] in place of [ENT].
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TH-F7E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TH-F7E in de taal/talen: Engels als bijlage per email.

De handleiding is 1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Kenwood TH-F7E

Kenwood TH-F7E Gebruiksaanwijzing - Nederlands - 64 pagina's

Kenwood TH-F7E Gebruiksaanwijzing - Français - 64 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info