3
6Place the nozzle into the milk and move the function lever to the lower steam
position ( ). The milk will begin to increase in volume and appear frothy ᕦ. To
obtain a creamier froth, rotate the jug with slow movements from the bottom
upwards.
7 Once the desired temperature and froth are obtained, stop the steam by
returning the lever back to the middle ( ) position.
●
Never allow the milk to boil as this will spoil the flavour of the coffee.
8 Pour the frothed milk into the cups containing the espresso coffee to make a
cappuccino.
9Switch off the steam button in order to make further cups of coffee.
Note: After having used the steam function. The OK indicator light will flash
quickly (once per
1
⁄4 second) for a short period to indicate the high temperature
(see Fig. F page ii) during which period of time the machine is not ready for
brewing coffee. Wait until the OK indicator light glows continuously (see Fig. G
page ii) otherwise the temperature will be too high and will burn the coffee.
hint
●
After frothing milk, dispense hot water from the steam/hot water nozzle (see
below) which will help clean the nozzle and help the boiler to cool down more
quickly.
to produce hot water for other drinks, eg tea, fruit
drinks
1Ensure that the pod filter holder with a pod holder is fitted to the coffee maker.
2Press the power on button and its light will glow and the OK indicator light will
flash.
3 When the OK indicator light stops flashing and glows continuously, place a cup
under the steam/hot water nozzle and move the function lever to the lower
steam position ( ). Hot water will dispense from the nozzle.
4 Switch off and unplug after use.
●
Never use teabags in the pod filter.
setting the dispensing volume
The coffee maker has been programmed to dispense a pre selected quantity of
liquid which is 40ml for Espresso, 125ml for a single café crema and 250ml for
a double café crema. These volumes can only be changed by carrying out the
following procedure ensuring that the appropriate coffee pod and pod filter are
fitted.
1 Place the required cups(s) under the coffee nozzle.
2Press and hold the Steam button for 5 seconds during brewing and the OK and
steam indicator lights will flash simultaneously. When the coffee volume in the cup
reaches the required level, release the button and the water volume will be stored in
the memory. This can be re-programmed at any time following the above
procedure.
descaling
When the power on light starts flashing the machine needs to be descaled and
it will continue to flash until the unit is descaled.
1 Place a jug under the steam/hot water nozzle and a suitably sized vessel under
the coffee outlet. (These may need to be emptied during the descaling process).
2 Fill the water tank to the MAX level with a liquid descaling agent.
3 Select the pod filter that is used most frequently or one that requires more
thorough cleaning. Fit the pod filter into the pod filter holder.
4Press the power on button and its light will glow and the OK indicator light will
flash.
5 When the OK indicator light stops flashing, turn the function lever to the lower
steam ( ) position and press the steam button for 3 seconds. At this stage the
machine activates the descale program and the Power, OK and steam indicator
lights will flash in sequence.
6 Allow half of the descaling agent to flow out from the steam/hot water nozzle.
7Turn the function lever to the upper coffee
()
position and the remaining
solution will flow from the coffee outlet. (The pump will cycle on for 30 seconds
and then switch off for 2 minutes. This will be repeated until the tank has
emptied and at completion the coffee maker will bleep.)
8 When the tank is empty return the function lever to the middle ( ) position. The
indicator lights will continue to flash as the descaling cycle is not complete.
9 Rinse the tank, fill with fresh water and empty and replace the containers
beneath the steam/hot water nozzle and coffee outlet.
10 Turn the function lever to the lower steam position ( ) and allow half the fresh
water to flow out from the steam/hot water nozzle and then turn the function
lever to the upper coffee position
()
.
11 Allow the remaining water to flow from the coffee outlet. (during this cycle the
pump will operate continuously until the tank has emptied and the coffee maker
will bleep.)
12 Turn the function lever to the middle ( ) position.
13 Switch off the coffee maker for 3 seconds to allow the coffee maker to reset.
14 Switch on the coffee maker which is now ready for use.
cleaning
1 Before cleaning, unplug and let everything cool.
2 Never immerse the appliance in water
3 Don’t wash parts in the dishwasher.
tank, pod filter, pod filter holder
●
Wash, rinse and allow to dry
steam/hot water nozzle
●
Prior to cleaning allow some hot water to flow out of the nozzle (see ‘to
produce hot water for other drinks’ ) then unplug and allow to cool before
proceeding.
●
Unscrew the nozzle by turning anti-clockwise, then wash thoroughly. Check
that the hole in the nozzle is not blocked. If necessary unblock with a pin.
●
Clean the steam/hot water delivery tube. Make sure the end is not blocked .
●
Screw the nozzle back onto the delivery tube.
drip tray/drip tray cover
●
Empty the drip tray regularly.
1Wash then dry thoroughly.
service and customer care
●
If the cord is damaged it must, for safety reasons, be replaced by Kenwood or
an authorised Kenwood repairer.
If you need help with:
●
using your machine or
●
servicing, spare parts or repairs
Contact the shop where you bought your machine.
