Handleiding Kenwood ES020 series (pagina 5 van 87) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins)

510774

Verklein

Vergroot

Pagina terug

1/87

Pagina verder

8 When you’ve enough coffee – not too much otherwise it will be too weak, press

the coffee button. If you’re not making more coffee press the on/off button to

switch off the machine. The chart below gives a guide on how long to operate

the coffee button to produce drinks of different volumes.

9 Wait for 30 seconds then remove the filter holder by turning to the left.

● There may be water on the filter when you remove it: this is normal

10 To remove the used coffee from the filter holder, flip the lever on the handle so

that the end locates over the filter ᕣ. Hold the lever in position then tip the unit

upside down and tap out the grounds ᕤ.

Important

Never remove the filter holder while the coffee or steam function

is selected – steam could shoot out and burn you.

to make coffee using filter pods

Important

If the filter for one cup is used after ground coffee has been used, it is

necessary to clear any ground coffee from around the coffee outlet. This is

necessary to avoid water leakages from the filter holder and to ensure optimum

performance. Take care as the area may be hot.

1 Pre heat the machine as described on page 2, fitting the small filter in the filter

holder.

2 After pre-heating remove the filter holder and place the coffee pod into the filter

making sure the pod is facing the correct way ᕥ.

3 Press the pod towards the lower part of the filter, making sure that the paper

flaps adhere to the inner part of the filter.

4 The pod needs to be well centred and placed firmly in the filter.

5 Fit the filter holder into the coffee outlet and turn to the right until it locks into

position ᕡ.

6 Follow the points ‘to make espresso’.

Note – use pods that conform to the ESE standard.

● Always follow the instructions on the package of the

pods for the correct positioning of the pods in the filter

to froth milk for cappuccino

Prepare the espresso as previously described

hint - to prepare more than one cappuccino, first make all the coffees then at

the end prepare the frothed milk for all the cappuccinos.

1 Make sure there is water in the tank.

2 Ensure that the variable steam control is closed.

3 Press the on/off button and it will glow orange.

4 Press the steam button and the red steam indicator light will flash.

5 Wait until the red light glows continuously indicating that the unit has reached

the correct temperature.

6 Part fill a jug with milk – the milk may increase up to three times in volume so

select a suitably sized jug. As a guide use 40-60 ml milk per cappuccino.

● Cold semi skimmed milk gives the best results.

7 Hold the jug in one hand and place the nozzle in the milk, ensure that the milk

does not go above the join in the nozzle.

8 Open the variable steam knob by turning in an anti clockwise direction. The

milk will begin to increase in volume and become frothy ᕦ. Adjust the height of

the jug ensuring that the tip of the nozzle remains below the surface of the milk.

After 20-25 seconds the milk will be steamed and frothy.

9 Stop the steam by turning the varialble steam knob in a clockwise direction.

● Never allow the milk to boil as this will spoil the flavour of the coffee.

10 Press the steam button.

11 Pour the frothed milk into the cups containing the espresso coffee. For coffee

latte hold back the froth and just add the steamed milk.

Important – Never operate the steam nozzle for longer than 2 minutes at one

time, and always clean the nozzle after use.

12 Press the on/off button to switch off.

quantity filter size approximate time to dispense

1 Espresso (40ml) 1 cup 12 sec

2 x Espresso (40ml each) 2 cup 25 sec

1 large coffee (125ml) 1 cup 32 sec

2 large coffees (125ml each) 2 cup 65 sec

to make espresso after frothing milk

Important

Never remove the filter holder from its housing immediately after using the

steam fuction.

If you’re making espresso after frothing milk, you need to get rid of any over-hot

water that could burn your coffee. Here’s how:-

1 Switch off the steam button.

2 Ensure there is water in the tank and place a jug beneath the steam nozzle.

3 Open the variable steam knob by turning anti-clockwise and press the coffee

button (water/steam will come out of the steam nozzle). Wait until the green

light flashes then close the variable steam knob and switch off the coffee

button

4 Wait for additional time until the green light glows continuously. When this

happens the machine is ready to make coffee.

cleaning

steam nozzle

Prior to cleaning the steam nozzle allow some hot water to flow out of the

nozzle to assist with the cleaning operation. This should be carried out

immediately after having dispensed steam. Here’s how:-

1 Ensure there is water in the tank and that there is a jug under the steam nozzle.

2 Switch off the steam button.

3 Open the steam knob by turning in an anti-clockwise direction.

4 Press the coffee button and operate for approximately 10 seconds to allow hot

water to pass through the nozzle.

5 Switch off the coffee button then close the variable steam knob by turning

clockwise.

6 Press the on/off button to switch off the machine.

● Before further cleaning, unplug and let everything cool.

● Never immerse the appliance in water.

● Don’t wash parts in the dishwasher.

steam nozzle

1 Unscrew the nozzle by turning clockwise, then wash thoroughly. Check that the

3 holes indicated are not blocked Ƹ. If necessary unblock them with a pin.

2 Clean the steam tube. Make sure the end is not blocked.

3 Screw the nozzle back onto the delivery tube.

tank, lid, filter holder

● Wash, rinse and allow to dry.

filter (one and two cup version)

● Wash and dry after every use.

● After approximately every 100 uses dismantle and clean more thoroughly as

described below.

● Remove the cap located on the underside of the filter by turning in the direction

indicated ᕧ. Remove the crema device by pushing up from the underside ᕨ.

Separate the components of the crema device by pulling the gasket to the side

ᕩ and removing the plastic disc and metal filter µ. Rinse parts thoroughly.

Clean the metal filter in hot water using a brush ¸. Make sure the holes in the

metal filter are not blocked. If necessary clean with a pin ¹. Dry the parts then

reassemble, making sure the parts are correctly assembled.

cup stand, drip tray

● Empty the drip tray regularly. You’ll know when it is full, the red float in the

middle of the drip tray will rise and become visible in the hole on the cup stand.

1 Wash then dry.

coffee outlet

● After every use check that this area is clean and free from any coffee grounds.

Wipe clean and if necessary carry out the following procedure to clean more

thoroughly. Failure to keep this area clean will affect the quality of the coffee

produced and may damage the unit.

1 Using a screwdriver ƹ, unscrew the screw that holds the coffee outlet in place

(do not remove the inner cover).

2 Clean the area with a damp cloth.

3 Clean the removed outlet thoroughly in hot soapy water using a brush. Rinse

thoroughly. Make sure the holes are not blocked, if necessary use a pin to

clean.

4 Reverse the above procedure to re fit to the outlet.

Failure to clean the coffee outlet and the filters as described invalidates the

guarantee.

Kenwood ES020 series Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info