686369
10
Verklein
Vergroot
Pagina terug
1/66
Pagina verder
10
A7 MIG Welder© Kemppi Oy 2018 1804
INTEGRATION GUIDE
3.6.5 Touch-sensing with the gas nozzle
The default way to use the touch sensor of the welder
system is to use the welding wire as the touch tool.
Alternatively, you can use the gas nozzle of the welding
torch.
If the gas nozzle is used for touch-sensing, connect pin F of
the peripheral connector to the gas nozzle, using an extra
wire (see Figure 3.7, Touch sensor gas nozzle connection).
For instructions on how to congure the touch sensor, see
the A7 MIG Welder Operating manual.
F
Figure 3.7: Touch sensor gas nozzle connection
3.7 Collision sensor
The collision sensor is an external device that protects
the torch neck from bending and being damaged. It is
integrated into the mount between the robot arm and the
welding torch. The sensor sends a signal to the robot to
stop welding when a collision is detected at the welding
head.
Not all robot mounts feature a collision sensor. See the
manual of the robot mount for more information.
The welder system supports two types of collision
sensors, an opening-action switch sensor and a closing-
action switch sensor. The opening-action switch keeps
the relevant electrical circuit normally closed and opens
it on a collision, while the closing-action switch keeps
the electrical circuit normally open and closes it upon a
collision (see Figure 3.8, “Opening-action and closing-
action switches”).
The switch type is congured via software. The collision
sensor conguration is described in Subsection 5.1.6,
“Collision sensor settings.
Figure 3.8: Opening-action (left) and closing-action (right)
switches
Connect the collision sensor to pins E and H of the peri-
pheral connector (see Figure 3.9, “Collision sensor
connection).
E
H
Figure 3.9: Collision sensor connection
Some collision sensors have LED status indicators coupled
with the switch and therefore require supply voltage.
Connect pin C of the peripheral connector to supply
power to the indicators (see Figure 3.10, “Collision sensor
with LED indicators).
C
E
H
Figure 3.10: Collision sensor with LED indicators
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi A7 MIG Welder 350 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi A7 MIG Welder 350 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info