771567
14
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
3.8 Connecting therefrigerant pipes
CAUTIONS DURING BRAZING
Replace air inside the tube with nitrogen gas to prevent copper oxide film from forming during the brazing process. (Oxygen, carbon dioxide
and Freon are not acceptable.)
Do not allow the tubing to get too hot during brazing.The nitrogen gas inside the tubing may overheat, causing refrigerant system valves to
become damaged. Therefore allow the tubing to cool when brazing.
Use a reducing valve for the nitrogen cylinder.
Do not use agents intended to prevent the formation of oxide film. These agents adversely affect the refrigerant and refrigerant oil, and may
cause damage or malfunctions.
TIGHTENING
In the table below are shown the pipes diameter for each unit
For the flare nuts at tubing connections, be sure to use the flare nuts that were supplied with the unit, or else flare nuts for R410A. The refrige-
rant tubing that is used must be of the correct wall thickness as shown in the table below.
Because the pressure is approximately 1.6 times higher than conventional refrigerant pressure, the use of ordinary flare nuts or thin-walled
tubes may result in tube rupture, injury, or asphyxiation caused by refrigerant leakage.
In order to prevent damage to the flare caused by overtightening of the flare nuts, use the table above as a guide when tightening.
When tightening the flare nut on the liquid tube, use an adjustable wrench with a nominal handle length of 200 mm.
INSULATING THE REFRIGERANT TUBING
Thermal insulation must be applied to all units tubing, including distribution joint (field supply). For gas tubing, the insulation material must be
heat resistant to 120°C or above. For other tubing, it must be heat resistant to 80°C or above.
Insulation material thickness must be 10 mm or greater.
If the conditions inside the ceiling exceed DB 30°C and RH 70%, increase the thickness of the gas tubing insulation material by 1 step.
ø Tube Tightening torque Tube thickness
ø 6,35 (1/4”) 14 - 18 N*m 0,8 mm
ø 12,7 (1/2)” 49 - 55 N*m 0,8 mm
Unit KRE-500DX1 KRE-1000DX1
Gas Pipe ø 12,7 mm
Liquid Pipe ø 6,35 mm
3.9 Connecting PRE-DX
The electric heater shall be connected to the suction of fresh air stream, both upstream and downstream to a duct of the same nominal diam-
eter; the duct must be fully inserted on the heater sleeve up to the stop, so that it fits the airtight gasket.
It is suggested to mount the heater as close as possible to the unit to which it is connected. For PRE-DX heater the ambient temperature
must be from -25°C to +30°C; degree of protection IP40.
The heater can be installed both horizontally and vertically; in case of horizontal electric heater, the electric box must be placed according to
one of the positions.
The heater must be adequately supported, so that unit connections are free from any stress.
The heater must not be insulated.
For BE heater, the supply air temperature must be lower than 50°C and the air speed must be higher than 2 m/s. Make sure that the
heater is turned ON only when the fan is switched on. The fan must continue to run at least 30 seconds after the heater has been
turned off.
Connections and cables that are used for them have to be supplied by the installer.
For power supply of the electric heater use a 3-wire cable (line, neutral, ground), sized for the specific current of the selected model. First,
pass along the free ends of the three cables from the inside of electrical board to the outside, through the glands on the basic unit.
pag. 14
Flare insulator
Insulation tape (white)
Flare union
Unit side
Flare nut Tube insulator
(not supplied)
Heat resistant
Insulation
Liquid tubing
Two tubes arranged together
Gas tubing
Modello / Model PRE-DX
Pt pre Ampere Dt nom Stadi /
Stages V / ph / Hz Ø A B C Peso /
Weight
kW °C mmmmmmmm kg
KRE-500DX1 1.5 6.5 9.0 1 230 / 1 / 50 200 400 289 200 4.6
KRE-1000DX1 2.5 10.9 9.0 1 230 / 1 / 50 250 400 342 260 4.8
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kaysun KRE-500DX1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kaysun KRE-500DX1 in de taal/talen: Engels als bijlage per email.

De handleiding is 2.81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info