771525
39
Verklein
Vergroot
Pagina terug
1/45
Pagina verder
Page 39
Wiring
1) The output of the mainboard engineering
load control interface is a strong electric
signal, so it must be powered o.
2) The engineering load control interface is only
used as a signal output. The total output
current of the mainboard cannot exceed
2.5A, otherwise it will cause overload and
damage the machine.
3) Please connect the engineering load in strict
accordance with the wiring diagram. The
excessive load power needs to be controlled
by the AC contactor. AHS and K_heater2
must pass the AC CONTACTOR control.
4) The connection and installation of external
engineering loads must be well protected,
such as earthed eectively, air switch and
residual current operated circuit-breakers.
The installation of engineering load shall be
installed in strict accordance with the
instruction manual of the load and control
components and local regulations.
"CN400" terminal is used for remote ON-OFF
switch; when using this function, this interface
is connected to external control switch,
remove the short connector of JR400 when
you use the "ON-OFF" function.
The control logic is as follows:
Remote switch short circuit: the machine is
controlled as normal.
Remote switch o: the machine enters remote
control.
3. Remote switch function
4. DIP SWITCH FUNCTION
5. Battery installation
1. The battery is placed in the accessory bag and
needs to be installed in the wired controller on
site.
2. Please remove the wired controller, place the
battery in the unit and ensure the positive side
of the battery is in accordance with the polarity
markings.
3. Set the correct time before operating. Battery
in the wired controller can maintain the correct
time during a power failure. When the power is
restored and the displayed time is not correct,
replace the battery.
Engineering load control interface
2-WAY VALVE
CODE PART NAME
SV2
Sv3_1,SV3_2 3-WAY VALVE
AHS CONTROL SIGNAL OF ASSISTANT
HEAT SOURCE
Pumpo PUMP
PumpT PUMP FOR RETURN WATER/PUMP
FOR MIXING WATER
K_heater2 CONTROL SIGNAL OF WATER
TANK HEATER
RY2,RY4 RELAY
DIP SWITCH
SW1
TW1B
ONFUNCTION DEFAULT SETTINGOFF
SW1-1
ON
1 2 3 4
SW1
SW1-3
SW1-2
SW1-4
OFF
OFF
OFF
OFF
TH
TK
WITHOUT
TW1B
WITH
TW1B
WITHOUT
TH
WITH
TH
WITHOUT
TK
WITH
TK
Note:Slide the switch
to numbers position
indicates OFF ." "
39

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kaysun KHHP-BI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kaysun KHHP-BI in de taal/talen: Engels als bijlage per email.

De handleiding is 18.24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kaysun KHHP-BI

Kaysun KHHP-BI Gebruiksaanwijzing - Nederlands - 48 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info