771475
25
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
24
2.
Electrical Power Connection
1-phase
Residual Current
Circuit-breaker
A
3-phase
B C N GND
B C N GND
AC 380-415V 50Hz
L
N
GND
Residual Current
Circuit-breaker
L
N
GND
AC 220-240V 50Hz
NOTE:
The outdoor units must be installed with an Residual Current
Circuit-breaker near the power supply and must be effectively
earthed.
Remote cooling/heating
SWITCH 2
If switch2 is closed, the unit will shift to heating mode forcibly;
If switch2 breaks the unit will shift to cooling mode forcibly.
Remote shutdown and Remote cooling/heating is optional
function.
Choose this function by DIP switch SW4_1 (for 1-phase) or
SW3_1 (for 3-phase) on PCB board. Factory default has no
remote cooling/heating.
3.
Auxiliary function connections
Additional pump
When the remote control and wire controller used at the same
time, the unit will carry out the last command of arbitrary
terminal.
Remote shutdown has the highest priority. In the status of
remote shutdown, other controllers can’t start the unit.
Wire controller
“PUMP2” terminal only provides passive switching signal.
Additional water pump must be controlled by the AC contactor.
Remote alarm
5kW / 7kW 10kW ~ 16kW
The wire controller is optional.
Please use 3-core shielded wire to connect the wire controller and
the shielding layer must be grounded.
When connecting wire controller, host unit control panel is
mainly used for display which can carry out parameter inquiry
such as inquiry and checking and can’t be used to set mode and
temperature.
“Remote alarm” terminal only provides passive switching signal.
Current passing through the terminal interface should less than 1.5A,
otherwise please use AC contactor to control load indirectly.
Remote shutdown
SWITCH
If switch is closed, the unit will be stopped forcibly.
Under this circumstance, anti-frozen protection and other
protection functions are still effective.
If switch breaks, unit can run normally according settings.
NOTE
Main control board
L
N
220-240V
L
220-240V
N A1
AC contactor
A2
Additional pump
Main control board
ON
ON
Without Remote
central function
(Factory default)
With Remote
central function
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kaysun KEM-14 DTN bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kaysun KEM-14 DTN in de taal/talen: Engels als bijlage per email.

De handleiding is 7.07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kaysun KEM-14 DTN

Kaysun KEM-14 DTN Gebruiksaanwijzing - Nederlands - 48 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info