Handleiding Kaysun Aquantia PRO Monobloc - KHP-MO (pagina 36 van 80) (Engels)

771521

Verklein

Vergroot

Pagina terug

1/80

Pagina verder

A main switch or other means of disconnection, having a contact separation in all poles, must be incorporated in the

fixed wiring in accordance with relevant local laws and regulations. Switch off the power supply before making any

connections. Use only copper wires. Never squeeze bundled cables and make sure they do not come in contact with

the piping and sharp edges. Make sure no external pressure is applied to the terminal connections. All field wiring and

components must be installed by a licensed electrician and must comply with relevant local laws and regulations.

The field wiring must be carried out in accordance with the wiring diagram supplied with the unit and the instructions

given below.

Be sure to use a dedicated power supply. Never use a power supply shared by another appliance.

Be sure to establish a ground. Do not ground the unit to a utility pipe, surge protector, or telephone ground. Incomplete

grounding may cause electrical shock.

Be sure to install a ground fault circuit interrupter (30 mA). Failure to do so may cause electrical shock.

Be sure to install the required fuses or circuit breakers.

WARNING

9.7.2 Wiring overview

The ground fault circuit interrupter must be a high- speed type breaker of 30 mA (<0.1 s).

NOTE

This unit is equipped with an inverter. Installing a phase advancing capacitor not only will reduce the power factor improve-

ment effect, but also may cause abnormal heating of the capacitor due to high-frequency waves. Never install a phase

advancing capacitor as it could lead to an accident.

The illustration below gives an overview of the required field wiring between several parts of the installation. Refer also to "8

Typical application examples".

Secure the electrical wiring with cable ties as shown in figure so that it does not come in contact with the piping, particularly

on the high-pressure side.

Make sure no external pressure is applied to the terminal connectors.

When installing the ground fault circuit interrupter make sure that it is compatible with the inverter (resistant to high frequency

electrical noise) to avoid unnecessary opening of the ground fault circuit interrupter.

Fix cables so that cables do not make contact with the pipes (especially on the high pressure side).

9.7.1 Precautions on electrical wiring work

9.6 Water piping insulation

9.7 Field wiring

The complete water circuit including all piping, water piping must be insulated to prevent condensation during cooling operation

and reduction of the heating and cooling capacity as well as prevention of freezing of the outside water piping during winter. The

insulation material should at least of B1 fire resistance rating and complies with all applicable legislation. The thickness of the

sealing materials must be at least 13 mm with thermal conductivity 0.039 W/mK in order to prevent freezing on the outside water

piping.

If the outdoor ambient temperature is higher than 30°C and the humidity is higher than RH 80%, then the thickness of the

sealing materials should be at least 20 mm in order to avoid condensation on the surface of the seal.

NOTE

During filling, it might not be possible to remove all air in the system. Remaining air will be removed through the

automatic air purge valves during the first operating hours of the system. Topping up the water afterwards might be

required.

The water pressure indicated on the manometer will vary depending on the water temperature (higher pressure at

higher water temperature). However, at all times water pressure should remain above 0.3 bar to avoid air entering

the circuit.

The unit might drain-off too much water through the pressure relief valve.

Water quality should be complied with EN 98/83 EC Directives.

Detailed water quality condition can be found in EN 98/83 EC Directives.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Kaysun Aquantia PRO Monobloc - KHP-MO Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Kaysun Aquantia PRO Monobloc - KHP-MO

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info