522389
5
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
Reinstall Check Valves
1. Install the new membrane housing O-ring (Bag A) on the pump front, and lubricate it with silicon
lubricant.
2. Install the new check valve components (Bag C) into the pump front, in the order shown. Lubricate
the O-rings with silicone lubricant before assembly.
3. Insert the spring into its recess in the valve retainer plate, then reinstall the plate over the check
valves in the pump front. Maneuver the retainer plate until it sits squarely (not tilted).
Reattach Pump Back and Pump Front Assemblies
1. Set the pump front upright. The end that attaches to the membrane housing should be at the
bottom.
2. Hold the pump back over the pump front, align the tabs on the two, and press the piston cylinder
into the opening over the valve retainer plate. Push in until the two components fully mesh.
3. If the spacer has fallen off the pump front, reinstall it.
4. Push the collar and threaded rods onto the pump assembly. The collar and pump don’t have to be
completely flush when assembled.
5. PowerSurvivor-35 only. Reinstall the gland plate on the end of the pump back. The outside of the
plate is flat; the inside has a recess which matches the shoulder on the pump back.
Reattach Handle to Pump (Survivor-35)
1. Install the two links onto the pivot pins of the piston shaft and handle. The flanges on the bushings
should be on the inside of the links; the center hole in the links must be closer to the piston shaft
pivot pin than it is to the handle pivot pin.
2. Hold the spacer between the links, and install the link screw.
3. Install the two halves of the mechanical housing, using the ¾-in. capscrew.
4. Align the mechanical housing with the pump back, and reinstall the four long capscrew.
Alternately tighten them to 40 in.-Ibs.
Reattach Manifold to Pump
1. Unscrew and remove the spool valve
retainer, by inserting a needle-nose pliers
into the retainer slots and turning.
2. Pull the retainer cap off of the retainer with
the pliers. Remove the stem seal from inside
the retainer.
3. Install the new valve stem seal, lubricate it
with silicone grease, and reassemble.
4. Install the new O-rings onto the hose
adapter, and push it into the manifold.¨
5. If leakage is evident, remove the large and
small rubber plugs from the back of the
manifold. Remove the O-rings from the
plugs, and replace them with new O-rings
(Bag A). Reinstall the plugs.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Katadyn REPAIR SEAL KIT Survivor 35 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Katadyn REPAIR SEAL KIT Survivor 35 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info