804769
16
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
16 English
Adjusting the chain tension
1. With the Multi-Tool assembled, remove the battery
pack (see Multi-Tool MT 36 Bp operating instruc-
tions).
2. Release the guide rail nut.
Illustration I
3. Adjust the chain tension with the screw.
Illustration J
4. Check the chain tension.
Illustration F
The distance between the guide rail and the chain
must be 4,0 mm.
5. Tighten the guide rail nut.
Replacing the chain
1. Remove the guide rail nut.
Illustration K
2. Loosen the screw to adjust the chain tension
3. Remove the bar cover.
Illustration L
4. Remove the guide rail.
5. Dispose of the old chain professionally.
6. Fit the new chain on the guide rail.
Illustration M
7. Mount the guide rail. Pay attention to the running di-
rection of the chain.
Illustration N
8. Mount the bar cover, loosely fastening the guide rail
nut.
Illustration O
9. Adjust the chain tension (see Chapter Adjusting the
chain tension).
Troubleshooting guide
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
As the battery pack ages, even if it is looked after, its ca-
pacity reduces such that the full run time will no longer
be reached when fully charged. This does not indicate a
defect.
Warranty
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
Technical data
Subject to technical modifications.
Vibration value
WARNING
The specified vibration value was measured using a
standard test procedure and may be used to compare
devices.
The specified vibration value may be used in a provi-
sional assessment of the load.
Depending on the way the device is used, the vibration
emission can deviate from the specified overall value
during the current use of the device.
Fault Cause Rectification
The device stops during
operation
Chain blocked by clippings. Remove the clippings.
Motor has overheated Stop working and allow the motor to cool
down.
Problems when mount-
ing the shaft compo-
nents
The connection points are dirty. Clean the shaft ends of adhering dirt.
Only place the accessories on clean sur-
faces.
MT 36
Bp
MT CS
250/36
Bp
Device performance data
Working voltage of the bat-
tery
V36
Maximum speed /min 10000 ±
10%
Chain oil tank volume ml 200
Cut material diameter
(max.)
mm 180
Working range (max.) m 2,7
Dimensions and weights
Length x width x height mm 951 x
197 x
188
946 x
117 x
168
Weight (with battery pack) kg 2,6
Weight kg 2,0
Device performance data (measured with MT 36 Bp
Multi-Tool)
Sound power level as per EN ISO 11680-1 (meas-
ured with MT 36 Bp Multi-Tool)
Sound pressure level LpA dB(A) 92,6
Uncertainty KpA dB(A) 3,0
Sound power level LwA dB(A) 100,7
Uncertainty KWA dB(A) 0,8
Vibration value as per EN ISO 11680-1 (measured
with MT 36 Bp Multi-Tool)
Front handle hand-arm vi-
bration value
m/s23,0
Rear handle hand-arm vi-
bration value
m/s22,9
Uncertainty K m/s21,5
MT 36
Bp
MT CS
250/36
Bp
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Karcher MT CS 250-36 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Karcher MT CS 250-36 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 17.88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info