803426
12
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
12 English
Note
The decalcification cartridge must be installed in the wa-
ter reservoir when filling the water reservoir.
Filling the water reservoir directly on the device
1. Hold the device firmly.
2. Open the reservoir cover, and fill the water reservoir
with max. 0.4 l tap water, directly at the device.
Illustration F
3. Close the reservoir cover.
Removing the water reservoir for filling
1. Hold the device firmly.
2. Pull the water reservoir vertically upwards by the
handle.
3. Open the reservoir cover, and fill with max. 0.4 l tap
water.
Illustration G
4. Close the reservoir cover.
5. Insert the water reservoir and press downwards until
it locks into place.
Switching on the device
ATTENTION
Device and material damage due to tipping over
The device can fall over and be damaged if inadequate-
ly secured during work breaks or storage. Liquid can al-
so leak out and damage the floor covering in the
process.
Position the device with the floor nozzle on a solid base,
or the handle with the wall anti-slip protection in a verti-
cal position on a solid wall.
Installation information
When steaming for the first time after removing and re-
inserting the decalcification cartridge, the steam jet may
be weak or irregular, and individual drops of water may
be expelled. The device requires a short running-in pe-
riod in which the decalcification cartridge fills with water.
The steam volume that is expelled increases constantly
until the maximum steam volume has been reached af-
ter approx. 50 seconds.
Note
Please note that here it is set to steam stage 2 (tiles/
stone), since the running-in period will otherwise be ex-
tended.
1. Place the device on a firm surface.
Illustration H
2. Plug the mains plug into a mains socket.
Illustration I
3. The indicator light flashes red alternately.
Illustration J
4. The indicator light lights up constantly green after
approx. 30 seconds.
Illustration K
The device is ready for use.
Regulating the steam volume
The steam volume setting depends on the surface to be
cleaned.
Note
Controlling the volume of steam only works for the SC 2
Upright EasyFix. Only one steam stage is available for
the KST 2 Upright.
Press the button with the direction arrows on the
handle repeatedly until the desired steam stage is
selected.
Illustration L
2 different steam stages are available:
Note
The maximum steam stage (Tiles/stone) is always se-
lected when the device is switched on.
Press the steam lever after setting the steam vol-
ume.
Illustration M
Refilling water
Note
The water level can be seen through the partially trans-
parent fresh water reservoir.
When the water is refilled, the decalcification cartridge
remains fixed in the device.
Open the reservoir cover, and fill the water reservoir
with max. 0.4 l tap water, directly at the device.
Illustration F
or
Remove the water reservoir, open the reservoir cov-
er, and fill with max. 0.4 l tap water, see chapter Fill-
ing water.
Illustration G
Interrupting operation
ATTENTION
Material damage due to condensate/moisture
The floor covering can be damaged by moisture remain-
ing on the floor cleaning cloth or floor nozzle/device af-
ter cleaning.
Remove the floor cleaning cloth and dry the floor nozzle/
the device after finishing the cleaning work.
Do not place or store the device on heat-sensitive sur-
faces.
In order to save energy, we recommend that you switch
off the device for breaks in operation of longer than 20
minutes.
1. Pull the mains plug out of the socket.
Illustration N
Switching off the device
1. Pull the mains plug out of the socket.
Illustration N
ATTENTION
Device damage due to water putrefaction
The water in the reservoir may putrefy if the device is
not put into operation for more than 2 months.
Drain the water reservoir before longer breaks in oper-
ation.
2. To drain the water reservoir, see chapter Draining
the water reservoir.
Illustration O
Storing the device
1. To remove the floor cleaning cloth, see chapter
Floor nozzle.
Illustration C
2. Remove the moisture from the floor nozzle/device.
3. Wind the power cable around the lower and upper
cable hooks.
Illustration P
Tiles/stone - maximum steam stage
Wood - minimum steam stage
12

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Karcher-KST-2-Upright-EasyFix

Zoeken resetten

  • Tijdens de werking begonnen de twee rode lampjes plots te knipperen en stopte het stomen. De ontkalkingspatroon werd correct vervangen, maar de controlelampjes blijven rood knipperen. Er komt geen stoom. Wat kan er aan de hand zijn? Gesteld op 3-10-2023 om 12:17

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Karcher KST 2 Upright EasyFix bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Karcher KST 2 Upright EasyFix in de taal/talen: Alle talen als bijlage per email.

De handleiding is 13.69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info