784440
60
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
60
Mounting the hood
Note: When installing backow aps or a backow valve, make sure that they can open
freely. Otherwise, the suction power may be reduced and the operating noise of the
cooker bonnet increased.
Note: If the extractor hood is used for for recirculating air without venting to the outside,
it is important that the air outlet is not blocked, as otherwise the extractor hood will be
damaged, the capacity can be reduced and the operating noise will increase. It should
also be noted that a non-return valve cannot be installed.
3
The range hood must be pushed up until the mountings ”click”�over the construction the
range hood is to be mounted in.
If the mountings does not click”�they can be pushed in place, b y pressing on the screws
that holds the mountings.�This is done by pushing through the four holes in the corners of
the range hood with a screwdriver.
Note:�when mounting in a horizontal division recommends that the range hood
is insulated to avoid noise nuisance.
Click!
4x
Click!
Ceiling
Range hood
Mounting
4x
4
Adjust the mountings until the edge of the
range hood is level to the ceiling.�This is
done using a Philips screwdriver through the
four holes in the corners of the range hood.
NOTE:After the adjustment the enclosed
plugs must be mounted in the screw
holes.�Otherwise noise nuisance can be
experienced.
The vent pipe must be mounted after the adjustment of the range hood.�Thermex
recommends that a back valve is mounted on the vent installation to prevent draft
through the vent.�When installing an external motor from Thermex the none-return valve
is placed by the motor.
5
6
3
The range hood must be pushed up until the mountings ”click”�over the construction the
range hood is to be mounted in.
If the mountings does not click”�they can be pushed in place, b y pressing on the screws
that holds the mountings.�This is done by pushing through the four holes in the corners of
the range hood with a screwdriver.
Note:�when mounting in a horizontal division recommends that the range hood
is insulated to avoid noise nuisance.
Click!
4x
Click!
Ceiling
Range hood
Mounting
4x
4
Adjust the mountings until the edge of the
range hood is level to the ceiling.�This is
done using a Philips screwdriver through the
four holes in the corners of the range hood.
NOTE:After the adjustment the enclosed
plugs must be mounted in the screw
holes.�Otherwise noise nuisance can be
experienced.
The vent pipe must be mounted after the adjustment of the range hood.�Thermex
recommends that a back valve is mounted on the vent installation to prevent draft
through the vent.�When installing an external motor from Thermex the none-return valve
is placed by the motor.
5
6
3
The range hood must be pushed up until the mountings ”click”�over the construction the
range hood is to be mounted in.
If the mountings does not click”�they can be pushed in place, b y pressing on the screws
that holds the mountings.�This is done by pushing through the four holes in the corners of
the range hood with a screwdriver.
Note:�when mounting in a horizontal division recommends that the range hood
is insulated to avoid noise nuisance.
Click!
4x
Click!
Ceiling
Range hood
Mounting
4x
4
Adjust the mountings until the edge of the
range hood is level to the ceiling.�This is
done using a Philips screwdriver through the
four holes in the corners of the range hood.
NOTE:After the adjustment the enclosed
plugs must be mounted in the screw
holes.�Otherwise noise nuisance can be
experienced.
The vent pipe must be mounted after the adjustment of the range hood.�Thermex
recommends that a back valve is mounted on the vent installation to prevent draft
through the vent.�When installing an external motor from Thermex the none-return valve
is placed by the motor.
5
6
The cooker hood must be pushed upwards until the brackets „click“ over the construction
in which the cooker hood is to be mounted.
If the brackets do not „click, they can be brought into position by pressing the screws
holding the brackets. To do this, insert a screwdriver through the four holes in the corners
of the cooker hood, put it into the holes and press the holding screws.
Note: For horizontal installation, it is advisable to insulate the cooker hood to prevent the
formation of annoying noises.
ceiling
hood body
bracket
Note: Aer adjustment, the enclosed
plugs must be mounted in the screw
holes.
Otherwise, annoying noises may occur.
Adjust the brackets so that the edge of
the cooker hood is level to the ceiling.
This is done by inserting a screwdriver
trough the four holes in the corner of the
range hood as described before.
60

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw KKT Kolbe INTEGRA110 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van KKT Kolbe INTEGRA110 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 1.09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info