16
16.5 Grounds bin missing
GROUNDS BIN
MISSING
Ⅲ If this message lights up, the grounds bin is not installed properly
or missing altogether.
16.6 Filling the bean tank
COFFEE READY
FILL
BEANS
The display dialog system indicates which of the two bean tanks is
empty. Fill tank with beans as described in Chapter 3.4.
The bean level is monitored electronically on the IM PRESSA X9.
To ensure smooth operation, we recommend that you regular-
ly clean the bean tanks with a dry cloth. Switch the machine off
with the ON / OFF key (Fig. 5/A) before you do so.
Ⅲ Switch the machine off with the power switch on the rear of the
machine (Fig. 15/D).
16.7 Removing stones
Ⅲ Open the programming door on the front (Fig. 4) and switch the
IMPRESSA X9 off with the ON / OFF key (Fig. 5/A).
Ⅲ Switch the machine off with the power switch on the rear of the
machine (Fig. 15/D) and disconnect it from the mains supply.
Ⅲ Open the hinged door on reverse of the machine (Fig. 10).
Ⅲ Push sliders to the rear (Fig. 10) and take the bean tank out of the
machine.
Ⅲ Remove any beans with a vacuum cleaner.
Ⅲ Insert the key (Fig. 11).
Ⅲ Now turn the key counter-clockwise until the jammed stone is
released.
Ⅲ Remove any remaining powder with a vacuum cleaner.
Ⅲ Re-install the bean tank and pull the sliders to the front before
closing the door (Fig. 10).
16.8 General cleaning instructions
Ⅲ Never use sharp objects or caustic chemicals for cleaning.
Ⅲ Clean the inside and outside of the case using a soft, damp cloth.
Ⅲ Clean the pivoting steam spout (V) each time it was used.
Ⅲ After heating milk, draw off some steam to clean the inside of the
pivoting steam spout (V).
Ⅲ The water tank should be rinsed out and filled with fresh water
daily.
Visible calcification in the water tank can be removed using a
commercial decalcifying agent. Take out the water tank (Fig.2).
If you are using a CLARIS plus filter cartridge, remove it before
decalcifying the tank.
16.9 Disassembling and cleaning the dual spout
We recommend to disassemble and clean the dual spout if you
make milk products regularly.
Ⅲ Remove the cover of the height-adjustable dual spout by pressing
the Unlock key (Fig. 12) and remove the coffee distributor (Fig. 13).
Ⅲ Take off the spouts (Fig. 13).
Ⅲ Take the spouts apart (Fig. 14).
Ⅲ Thoroughly rinse all the parts with warm water.
Ⅲ Reassemble the parts (Fig. 14).
When assembling the dual spout, note the colour of the indi-
vidual parts (Fig. 14).
Ⅲ Attach the spouts to the IMPRESSA X9 (Fig. 13).
Ⅲ Put back the cover, making sure it locks into place (Fig. 13).
Use corresponding brushes for carrying out the cleaning steps
described in sections above.
16.10 Cleaning the milk system
We recommend to clean the milk system daily.
Once started, the cleaning process must not be interrupted. It takes
approx. 2 minutes.
Ⅲ Open the programming door on the front (Fig. 4).
Ⅲ Press the Clean Milk System key (Fig. 5/H) until you hear an
acoustic signal.
CLEAN CAPPU
START
YES
Ⅲ To initiate milk cleaning, press either the P button or the Milk
Cleaning button (Fig. 5/H).
CLEANER FOR CAPPUCCINO
PRESS
KEY
Ⅲ Place a receptacle with a capacity of at least 0.5 litres under the
height-adjustable dual spout (Fig. 6).
Ⅲ Fill a receptacle with approx. 4 dl of water and add 1 1/2 capfuls of
JURA cappuccino cleaning agent. Dip the two milk hoses into this
solution (Fig. 8/B).
Ⅲ Press the Clean Milk System key (Fig. 5/H).
MACHINE CLEANING
Ⅲ You will hear an acoustic signal.
WATER FOR CAPPUCCINO
PRESS
KEY
Fill a receptacle with approx. 4 dl of fresh water and dip the
milk hoses into it (Fig. 8/B).
Ⅲ Press the Clean Milk System key (Fig. 5/H).
MACHINE CLEANING
COFFEE READY
If you accidentally pressed the Milk Cleaning button (Fig. 5/H),
you can terminate the process after it has begun.
Ⅲ Press the ‘+’ or ‘–’ button until the following appears in the display:
CLEAN CAPPU.
START
NO
Ⅲ To ensure that milk cleaning is not carried out, press the P button.
DURATION
APPROX 2’
