614555
49
Verklein
Vergroot
Pagina terug
1/51
Pagina verder
– 47 –
Phenomenon Cause Corrective measure
When tilting the sewing machine,
the buzzer beeps and the sewing
machine cannot be operated.
When tilting the sewing machine
without turning OFF the power switch,
Action given on the left side is taken for
safety sake.
Tilt the sewing machine after turning
OFF the power.
Solenoids for thread trimming,
reverse feed, wiper, etc. fail to work.
Hand lamp does not light up.
When the fuse for solenoid power pro-
tection has blown out
Check the fuse for solenoid power
protection.
Even when depressing the pedal
immediately after turning ON the
power, the sewing machine does not
run. When depressing the pedal af-
ter depressing the back part of pedal
once, the sewing machine runs.
Neutral position of the pedal has varied.
(Neutral position may be shifted when
changing spring pressure of the pedal
or the like.)
Execute the automatic neutral correc-
tion function of the pedal sensor.
The sewing machine does not stop
even when the pedal is returned to
its neutral position.
Presser foot does not go up even
when auto-lifter device is attached.
Auto-lifter function is OFF. Select “Automatic presser lifter is pro-
vided.” by auto-lifter function selection.
Pedal system is set to KFL system. Change the jumper to PFL setting to lift
the presser foot by depressing the back
part of the pedal.
Cord of auto-lifter device is not con-
nected to connector (CN37).
Connect the cord properly.
Touch-back switch fails to work. Presser foot is going up by auto-liter
device.
Operate the switch after the presser
foot lowered.
Auto-lifter device is not attached. How-
ever, auto-lifter function is ON.
Select “Automatic presser lifter is not
provided.” when auto-lifter device is not
attached.
Sewing machine fails to run. Motor output cord (4P) is disconnected. Connect the cord properly.
Connector (CN30) of motor signal cord
is disconnected.
Connect the cord properly.
2. Error codes
In case of the following, check again before you judge the case as trouble.
In addition, there are the following error codes in this device. These error codes interlock (or limit function)
and inform the problem so that the problem is not enlarged when any problem is discovered. When you
request our service, please conrm the error codes.
[Checking procedure of the error code]
1) Turn ON the power switch with switch 󱀖
held pressed.
2) With a bleep, serial numbers of the errors which
have occurred so far appear on the display sec-
tion A.
3) Press and switches to enable selec-
tion of the serial number. Select one of the serial
numbers you want to check and, in this state,
press switch 󱀔 to display the error code,
press switch 󱀕 to display the energized
time duration (upper four digits of hours and
minutes), or press switch 󱀖 to display the
energized time duration (lower four digits of hours
and minutes). (The aforementioned data are
displayed as long as the corresponding switch is
held pressed.)
󱀕
󱀖
Display section A
󱀔
49

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Juki DDL8700B-7 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Juki DDL8700B-7 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info