553865
12
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
-Do not mix new batteries or the old and worn-out.
INSTRUCTIONS FOR USE
Warning! Before using the machine.
-Make sure that the button is in the O position. Insert the batteries
in the lower part of the machine in the correct position and in the
position indicated in the picture or connect the AC/DC adaptor in
its corresponding socket and then to the power supply.
-Connect the control pedal in the socket in the lower part of the
machine.
Indications to take into account:
-To use the machine either the control pedal or the ON switch
can be used.
NOTE: Always disconnect and switch off the machine when not
in use.
HOW TO THREAD THE TOP THREAD (fig1)
-Lift up the presser foot lever and lift the needle by turning the
balance wheel following the arrow indicated on the same. Follow
the following instructions:
1.- Lift the bobbin pin and put it in place (n).
2.- Pull the thread through guide 3 (o).
3.- Lead the thread through the tension disc (q).
4.- Pull the thread through guide 4 (s).
5.- Lead the thread through the hole in the bar to tighten (r).
6.- Lead the thread through guides 1 (a) and 2 (c).
7.- Lead the thread through the eye of the needle (d) from front
to back.
PUTTING THE LOWER BOBBIN IN PLACE
1.- With your left hand, hold the end of the thread leaving about
8 cm outside.
2.- Pull the threader downwards by the central plate groove
(fig2). Lead the thread between the wires of the threader and
pull to take the thread out by the groove.
3.- Put the bobbin in place. The thread has to be lead clockwise.
4.- Leave out about 10 cm of thread on the top part of the bobbin
towards the presser foot.
5.- Cover the bobbin with its lid.
HOW TO START SEWING
1.- Lift the needle by turning the balance wheel clockwise. Lift up
the presser foot.
2.- Make sure that the two ends of the thread are placed needle
backwards at least 10 cm.
3.- Put the garment in place, hold it down with the presser foot
and lower the needle manually.
4.- Press the pedal or press the O/I button until I position and
start sewing. Slide the garment with your hand. Do it slowly for
the first few stitches. If, while sewing, by using either the pedal
or through the On button, you need to modify the sewing speed,
press the speed control button: I position, normal speed and II
position, faster speed.
5.- To stop sewing, either stop pressing the pedal or place the on
button in O position.
IMPORTANT:
When finishing, lift up the needle manually, and in this way it will
not bend when taking the garment out; lift up the presser foot
and withdraw the garment. Then cut both threads at 10 cm. in
length.
HOW TO ADJUST THE THREAD TENSION
-Revise if the lower thread and the top one have the same tension
and if this tension is strong enough to close both threads in the
centre.
-If the top thread is too tight, the bobbin thread will be in the top
part of the garment. For this, slacken the needle thread tension.
-If the top thread is too loose, the needle thread will be on the
lower part of the garment. To correct this, tighten the thread.
WINDING THE LOWER BOBBIN
1.- Slide back the lid and extract the empty bobbin.
2.- Adjust the rewinding spindle in the hole for the winding of the
bobbin (l). Turn counter-clockwise.
3.- Lift up the foldable spindle (p) and insert a thread bobbin.
22-EN
EN-23
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jocca 6642 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jocca 6642 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 0,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info