686634
5
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
SRP-14-GB(V3)
PB
SRP-14-GB(V3)
READ CAREFULLY AND KEEP IT FOR FUTURE REFERENCE!
IMPORTANT SAFETY RULES
READ, UNDERSTAND, AND FOLLOW ALL INSTRUCTIONS CAREFULLY
BEFORE INSTALLING AND USING THIS PRODUCT !
Rectangular Steel Frame Pool
OWNER’S MANUAL
FOR FOLLOWING SIZES:
-10’x6,8’x27,6” (3mx2.07mx70 cm) -74”x50”x16,5”(1.88mx1.27mx42 cm)
-13’x6,8’x31,5” (3.94mx2.07mx80 cm) -90”x62,6”x16,5”(2.28mx1.59mx42 cm)
-8,5’x6’x26” (2.58mx1.79mx66 cm)
1
DO NOT RETURN PRODUCT TO STORE
CONTACT YOUR LOCAL AFTER SALES SERVICE CENTER
Drawing for illustration purpose only. Actual product may vary. Not to scale.
STOP!
32
SRP-14-GB(V3)
IMPRTANT SAFETY RULES------------------------------------------------------------------------------------02
PART REFERENCE------------------------------------------------------------------------------------------------04
SITE SELECTION---------------------------------------------------------------------------------------------------08
SET UP THE POOL-----------------------------------------------------------------------------------------------09
FILL THE POOL WITH WATER--------------------------------------------------------------------------------10
DISASSEMBLY AND STORAGE -----------------------------------------------------------------------------11
IN-SEASON POOL MAINTENANCE AND WATER CARE-------------------------------------------12
TROUBLE SHOOTING ------------------------------------------------------------------------------------------13
LIMITED WARRANTY ------------------------------------------------------------------------------------------ 14
CONTENTS
1). It is the responsibility of the pool owner to identify and obey all local and state laws pertaining to above ground
swimming pool safety PRIOR to set-up or use of the pool. These include, but are not limited to, laws on: decks,
fences, barriers, covers, pool ladders, lighting, and required safety equipment. Please consult your local authori-
ties to ensure compliance.
2). Do not allow unattended Children in the pool. Always make sure that at least one responsible adult is supervis-
ing all Children and those who do not know how to swim AT ALL TIMES. Never swim / bathe in the pool alone.
3). NEVER permit diving or jumping into the pool. Never enter the pool from any decks or other raised surfaces.
The water level in your pool is extremely shallow and is not suitable for these activities. Failure to heed these in-
structions can result in serious injury or even death.
4). Do not permit Children or adults to engage in any “rough-housing” or other aggressive sports or activity in or
around the pool. Failure to observe this guideline can result in serious injury for those in and around the pool area.
5). Always maintain the proper pool safety equipment in an easily accessible area adjacent to your pool. Clearly
post emergency phone numbers as well as safety advisories and rules (such as “No Jumping or Diving” and “Do
Not Swim Alone”). Do not allow bathers in the pool unless the area is sufciently bright or lighted.
6). All ltrations are in agreement with the installation standard NF C 15-100 that specify that all electric appliances
located within 3.50 m for the pond and with a free access should have a low voltage supply of 12V. All electrical
appliance supplied with 220V must be located at least at 3.50 meter from the edge of the pond. Consult the manu-
facturer for any change of one or several elements to the ltration system.(For France Market)
7). the safety of your children is up to you! The risk is greatest when children are younger than 5 years old. The
accidents do not only happen to others! Be ready to face it!
8). Watch and act:
WARNING:
To enhance the enjoyment of your pool and protect the
safety of those in and around the pool, ALWAYS STRICTLY OBSERVE the
following safety and maintenance instructions:
PART1-IMPORTANT SAFETY RULES
32
SRP-14-GB(V3)
Stay away from drains
& suction fittings
Your hair,body & jewelry can get sucked into drain.
You could be held under water & drown!
Zone 1
Zone 0
Zone 0
Zone 2
Zone 2
2.5m
2.5m
2.0m 2.0m 1.5m1.5m
h
h
PART1-IMPORTANT SAFETY RULES
- Supervision of children must be close and constant;
- Designate one responsible for security;
- Strengthen monitoring when there are multiple users in the pool;
- Teach your children to swim as soon as possible;
- Wet neck, arms and legs before entering the water;
- Learn lifesaving, especially those specic to children;
- Forbid diving or jumping in front of young children;
- Forbid running and violent games around the pool;
- Do not allow access to the pool without a shirt or bra for a child not knowing how to swim and not accompanied
in the water;
- Do not leave toys near unmonitored pool;
- Keep water clear and healthy;
- Store water treatment products out of reach of children;
9). Plan:
- Phone near the pool accessible to not leave your children unattended when you call;
- Buoy and pole near the pool;
10). Moreover, some devices may contribute to security:
- Barrier whose portal will be constantly kept closed (e g a hedge cannot be regarded as a protective barrier);
- Manual or automatic cover properly positioned and secured protection;
- Electronic sensor to detect or drop in service and operational, but not a substitute for close supervision;
11). Accident:
- Remove the child from the water as quickly as possible;
- Call for help immediately and follow the advice that given to you;
- Replace wet clothes with warm blankets;
12). Store and view pool numbers of rst aid:
- Fire: (18 for France);
- EMS: (15 for France);
- Poison Center.
13). Prohibit access to the pool for the deterioration or the system (s) lter;
14). Do not submerge;
15). Do not walk on the edge;
16). Warning: Never put the empty swimming pool in the open air.
54
SRP-14-GB(V3)
PART2-PART REFERENCE
Before assembling your pool, layout and review the contents to become familiar with all the parts you will
be using during the assembly:
NOTE: Drawing for illustration purpose only. Actual product may vary. Not to scale.
1
2
8
7
13
1
2
4
6
5
3
11
9
10
a
b
17
12
14
15
16
13’x6,8’x31,5” (3.94mx2.07mx80 cm)
NO. NAME QUANTITY SERIAL NUMBER QUANTITY SERIAL NUMBER
1 Horizontal Beam A
8 290256 8 393021
2 Horizontal Beam B
4 290257 4 393022
3 T-Joint
8 290252 8 393028
4 Vertical Leg
4 290262 4 393033
5
Vertical Leg
(with hole)
8 393061 8 393034
6 Vertical Leg Cap
12 290195 12 393030
7 L-Joint
4 290253 4 393031
8 Screw Set-M5*30
8 393020 8 393020
9 Y-Joint
8 290254 8 393027
10 Screw Set-M6*45
8 393029 8 393029
11 Tilted Leg
8 290263 8 393035
12 Tilted Leg Cap
8 290255 8 393026
13
Drainage Valve
Cover
1 290366 1 290366
14 Stopper
2 290311 2 290311
15 Hole Strainer
2 290312 2 290312
16
Drainage Valve
Connector
1 290364 1 290364
17 Pool Liner
1 011227 1 393036
Color BLUE GREY
13’x6,8’x31,5” (3.94mx2.07mx80 cm)
54
SRP-14-GB(V3)
PART2-PART REFERENCE
8
8
7
13
1
2
4
6
5
3
11
9
10
a
b
16
12
14
15
16
1
2
10’x6,8’x27,6” (3mx2.07mx70 cm)
NO. NAME QUANTITY SERIAL NUMBER QUANTITY SERIAL NUMBER
1 Horizontal Beam A
6 290256 6 393021
2 Horizontal Beam B
4 290257 4 393022
3 T-Joint
6 290252 6 393028
4 Vertical Leg
4 290258 4 393023
5
Vertical Leg
(with hole)
6 393060 6 393024
6 Vertical Leg Cap
10 290195 10 393030
7 L-Joint
4 290253 4 393031
8 Screw Set-M5*30
8 393020 8 393020
9 Y-Joint
6 290254 6 393027
10 Screw Set-M6*45
6 393029 6 393029
11 Tilted Leg
6 290259 6 393025
12 Tilted Leg Cap
6 290255 6 393026
13
Drainage Valve
Cover
1 290366 1 290366
14 Stopper
2 290311 2 290311
15 Hole Strainer
2 290312 2 290312
16
Drainage Valve
Connector
1 290364 1 290364
17 Pool Liner
1 011226 1 393032
Color BLUE GREY
NOTE: Drawing for illustration purpose only. Actual product may vary. Not to scale.
10’x6,8’x27,6” (3mx2.07mx70 cm)
76
SRP-14-GB(V3)
PART2-PART REFERENCE
8,5’x6’x26” (2.58mx1.79mx66 cm)
NO. NAME QUANTITY SERIAL NUMBER
1 Horizontal Beam A
4 290249
2 Horizontal Beam B
2 290250
3 Horizontal Beam C
2 290249
4 Horizontal Beam D
2 290250
5 T-Joint
6 290252
6 Vertical Leg
10 290251
7 Vertical Leg Cap
10 290195
8 L-Joint
4 290253
9 Screw Set-M5*30
8 393020
10 Drainage Valve Cover
1 290366
11 Stopper
2 290311
12 Pool Liner
1 011225
13 Hole Strainer
2 290312
14 Drainage Valve Connector
1 290364
Color
BLUE
9
8
11
1
2
3
4
a
b
5
6
7
12
10
13
14
NOTE: Drawing for illustration purpose only. Actual product may vary. Not to scale.
8,5’x6’x26” (2.58mx1.79mx66 cm)
76
SRP-14-GB(V3)
PART2-PART REFERENCE
90”x62,6”x16,5”(2.28mx1.59mx42 cm)
NO. NAME QUANTITY SERIAL NUMBER
1
Horizontal Beam
A
2 290245
2
Horizontal Beam
B
2 290246
3
Horizontal Beam
C
2 290247
4
Horizontal Beam
D
2 290248
5 T-Joint
4 290243
6 Vertical Leg
8 290242
7 Vertical Leg Cap
8 290185
8 L-Joint
4 290244
9 Screw Set-M5*25
8 393019
10
Drainage Valve
Cover
1 290364
11 Pool Liner
1 011224
Color BLUE
74”x50”x16,5”(1.88mx1.27mx42 cm)
NO. NAME QUANTITY SERIAL NUMBER
1 Horizontal Beam A
2 290239
2 Horizontal Beam B
2 290240
3 Horizontal Beam C
2 290241
4 T-Joint
2 290243
5 Vertical Leg
6 290242
6 Vertical Leg Cap
6 290185
7 L-Joint
4 290244
8 Screw-M5*25
8 393019
9
Drainage Valve
Cover
1 290364
10 Pool Liner
1 011223
Color BLUE
1
2
3
4
2
1
6
5
9
8
7
11
10
1
2
3
2
1
5
4
6
10
8
7
9
NOTE: Drawing for illustration purpose only. Actual product may vary. Not to scale.
90”x62,6”x16,5”(2.28mx1.59mx42 cm)
74”x50”x16,5”(1.88mx1.27mx42 cm)
98
SRP-14-GB(V3)
It is absolutely essential to select a suitable site for your pool BEFORE attempting to
ll it with any water. Please select a set-up site which strictly conforms to the following
guidelines:
Guide1. Ensure that the area is rm, at (no bumps or mounds of earth) and extremely level, with a grade not exceeding
3° of slope at any point in the set-up area.
Guide2. Make sure that the area you have selected to set-up the pool is completely free of sticks, stones, sharp objects or
other foreign debris.
Guide3. Select an area that is not directly underneath overhead power lines or trees. Additionally, make sure that the pool
set-up area does not contain underground utility pipes, lines, or cables or any kind.
Guide4. If a ground cloth is provided with your pool kit, its use is highly recommended. The ground cloth will help protect
the pool liner from damage due to weed growth, sharp objects, and debris.
Guide5. If at all possible, choose an open location on your property that is exposed to direct sunlight. This will help to
warm your pool.
WARNING:
Pools installed on inadequately level surfaces are subject to leaking,
forming irregularities, or collapse, which can result in property damage or serious in-
jury for those in or around the pool area!
WARNING:
Do not use sand during setup process. If it appears that there is a need
for use of a “leveling agent”, then your set-up site is likely unsuitable. FAILURE TO
OBEY THIS WARNING MAY RESULT IN SERIOUS PERSONAL INJURY.
CAUTION:
Please choose your set-up area carefully, as lawn and other desirable
vegetation underneath the ground cloth(If applicable) will die. Furthermore, try to avoid
setting the ground cloth(If applicable)in areas prone to aggressive plant and weed spe-
cies, as they may grow through the ground cloth(If applicable).
CAUTION:
The pool must be accessible to a 110 or 230-volt AC outlet protected by
a Ground Fault Circuit Interrupter (GFCI). The pool should be set no closer than 10 ft. to
the power source, but no further than the length of the lter pump cord. Under no cir-
cumstances should an extension cord be used to extend the range of the connection.
+3°
Bumpy,Sloping Ground-INCORRECT
Flat,Level Ground-CORRECT
PART3-SITE SELECTION
98
SRP-14-GB(V3)
Step3. INSTALL HORIZONTAL BEAM
Slide combined beams into sleeve,the hole on the beams should face outwards.
PART4-SET UP THE POOL
Step1. ACCOUNT FOR ALL PARTS.
Remove all the parts from the carton(s) and place them on the ground in the location where they are to be assembled
Check each part according to “PART REFERENCE” .Make sure all the pieces to be assembled are accounted for.
IMPORTANT: Do not start assembly if any pieces are missing. For replacement pieces call the Consumer Service
telephone number in your area.
The number of persons required for installation: 2 adult at least.
Total installation time except the time for site preparation and water lling :
45 minutes for size 10’×6.8'×27.6"/13'×6.8'×31.5"; 30 minutes for size 8.5’×6’×26”/74”×50”×16.5”/90”×62.6”×16.5”.
Step2. INSTALL DRAIN VALVES COVER AND STOPPER
Make sure that outer drain plug is inserted into the outer drain cap and drain valve cover is screwed on tightly.Plug the con-
nection holes with the stoppers. (The out drain plug changes according to different size of pool.)
STOPPER Out Drain Plug A Out Drain Plug BDrain Vavle Cover
BEAM A BEAM A
BEAM B
For 10’x6,8’x27,6” (3mx2.07mx70 cm) and 8,5’x6’x26” (2.58mx1.79mx66 cm), the combination is A-A-B.
BEAM A
BEAM B
For 74”x50”x16,5”(1.88mx1.27mx42 cm) and 90”x62,6”x16,5”(2.28mx1.59mx42 cm) , the combination is A-B.
BEAM C
For 74”x50”x16,5”(1.88mx1.27mx42 cm) , the short side is C.
BEAM A
For 13’x6,8’x31,5” (3.94mx2.07mx80 cm), the combination is A-A-A-B.
For the short side sleeve of the pool:
For the long side sleeve of the pool:
BEAM A BEAM C
BEAM B BEAM D
For 10’x6,8’x27,6” (3mx2.07mx70 cm) and 13’x6,8’x31,5”
(3.94mx2.07mx80 cm), the combination is A-B.
For 8,5’x6’x26” (2.58mx1.79mx66 cm)and
90”x62,6”x16,5”(2.28mx1.59mx42 cm), the combination is C-D.
BEAM A BEAM A BEAM B
1110
SRP-14-GB(V3)
Step4. INSTALL L-JOINT
1
2
3
4
1
3
2
2
4
5
3
6
1. Use the connection end of the L-JOINT to connect the
adjacent horizontal tubes.
2. Use the connection end of the L-JOINT to connect the vertical leg.
(Install the vertical leg cap on the leg before.)
3. Install the screws onto the L-JOINT rmly.
TIP: If you can’t nd the hole on the horizontal tube when you install the
screw, please rotate the horizontal tube until the hole meets the screw.
1. Install the horizontal beams.
2. Install the vertical leg cap onto the leg.
3. Insert the vertical leg into the T-JOINT.
4. Install the T-JOINT onto the connected horizontal beam.
TIP: If you can’t nd the hole on the horizontal tube when you
install the T-JOINT, Please rotate the horizontal tube until the hole
meets T-JOINT.
1. Install the horizontal beams.
2. Install the vertical leg cap and tilted leg cap onto the corroesponding leg.
3. Insert the vertical leg and tilted leg into the Y-JOINT.
4. Install the screw onto the vertical leg and Y-JOINT rmly.
5. Insert the installed vertical leg into the T-JOINT.
6. Install the T-JOINT onto the connected horizontal beam.
TIP: Please rotate the horizontal tube until the hole meets T-
JOINT if you can’t nd the hole on the horizontal tube.
TIP: Please rotate the vertical leg until the hole meets Y-JOINT if
you can’t nd the hole on the vertical leg.
Step5. INSTALL T-JOINT
Step6. INSTALL Y-JOINT(IF APPLICABLE)
WARNING:
Do not leave pool unattended while lling with water.
WARNING:
If more than 1~2 inches of water collects on any one side before you
start lling in the center.The pool is not level enough, and must be corrected! You
shall pull out the drain plug, release the water completely, disassemble the pool
completely,locate the pool on a plane surface, repeat set up instructiion.
WARNING:
DO NOT OVERFILL as this could cause the pool to collapse.In times of
heavy rainfall you may need to empty some of the water to ensure the level is correct.
PART5-FILL THE POOL WITH WATER
1. Make sure the drain tting is plugged securely and the cap
is in place. Start lling the pool with water. After about 1-inch of
water is on the bottom, stop lling and smooth wrinkles out of the
bottom of the pool. Pull the outer wall out from under the top ring,
all around the bottom of the pool, so that it lls evenly.
2. Contineue lling the pool until water level .
PART4-SET UP THE POOL
1110
SRP-14-GB(V3)
WARNING:
Do not let your children stand at downfold and face the water outlet
during the drainage. The water current may sweep your children.
WARNING:
Pool should be stored at places where is cool and dry, with no sharp
object surroued, or no heavy objects lying above, which may cause damage to the
pool.
PART6-DISASSEMBLY AND STORAGE
Step1. If you have a lter pump, make sure that the electricity source to the lter pump has been disconnected.
Step2. Check to ensure that the out drain plug is rmly inserted on the inside of the pool.
Step3. Attach your garden hose to the drainage valve connector, and placing the other end of the hose in an area where the
water can drain safely, such as a storm drain or street gutter. Remember that because water always nds its own level, the end
of the hose must be lower in elevation than the pool to ensure complete drainage.
Step4.If you have a lter pump, insert the stopper into the inlet and outlet xtures, on inside of pool, and then disconnect the
lter pump hoses.
Step5. Attach the drainage valve connector to the drain outlet by turning connector in a clockwise direction.
Step6. Open the out drain plug on the inside of the pool and the water will begin to drain immediately.
Step7. Disconnect the hose and drainage valve connector when nished.
Step8. Replace the out drain plug on the inside of the pool.
Step9. Be sure that the pool liner is completely dry before folding the pool for long-term storage. Leaving the pool exposed to
sunlight for a few hours will clean and speed the drying process and make it easier to fold the pool for storage. (Never attempt
to fold or stow a pool that is not completely dry as this could lead to a proliferation of mold or mildew build-up during the time
the pool is in storage.)
Step10. Remember, proper off-season storage is critical to protect your investment in your pool. (espeically in winter) Once
drained and dry, your pool should be carefully folded and wrapped in a ground cloth (if available) or other similar protective
tarp-like material. The pool and all applicable accessories such as the pump, cover, ground cloth, ladder, hoses, clamps, and
hardware should be kept together and stored indoors, in a reasonably warm, dry and weatherproof location.
Before folding, it’s better to dry all parts and pool completely by lying them in the sun
for one hour or so.(PIC.1). And then, spread some talcum powder to prevent the vinyl
from sticking together.
FOLDING INSTRUCTION
Step1. Please fold the protrusion sides inside to gain rectangle shape.(PIC.2).
Step2. Fold each half of the rectangle to gain a smaller rectangle shape.(PIC.3).
Step3. Fold each ends backwards. (PIC.4).
Step4. Fold the rest ends together to create an ultimate rectangle one.(PIC.5).
TIPS1. Please remove air inside to make the folded pool thin and at during each folding.
TIPS2. The original packing can be used for storage.
PIC.1 PIC.3 PIC.4PIC.2
PIC.5
1312
SRP-14-GB(V3)
PART7-IN-SEASON POOL
MAINTENANCE AND WATER CARE
This product is designed to be storable, seasonal pools. If you live in a temperate area in which the pool will not be in use
year-round, it is STRONGLY RECOMMENDED that you drain your pool, clean and dry it thoroughly, and store it in a protected
area for the off-season. This will help extend the life of your pool and prevent a safety hazard from developing while the pool is
not in use. During the season of use of the pool kit, the ltration system (if applicable) must be put into service each day, long
enough to ensure at least a complete renewal of the volum of water.
In order to keep your pool water clean and hygienic all season long please closely adheres to the follow-
ing guidelines:
1. The proper and consistent use of basic pool chemicals are required to maintain the proper pH balance in your pool water.
Furthermore, the application of chemicals will help prevent the growth of harmful bacteria or algae in your pool, and assist your
lter-pump in keeping your water crystal clear. Chemicals that your pool may require include but are not limited to:
1) Tabular, Granular, or Liquid Chlorine: Disinfects pool water and inhibits algae growth.
2) PH Adjusting Chemicals: These are used to correct PH level and make water more or less acidic.
3) Algaecides: These chemicals are formulated to remove algae.
4) “Shock” (Super chlorinator): Eliminates certain organic and other combination compounds that can affect water clarity.
In order to obtain specic details on the use of chemicals, please consult a local pool supply retailer and provide them with
the volume of water in your specic pool, and if desired, a sample of your pool water. This will enable them to properly instruct
you on: 1) which chemicals to purchase, 2) what quantities of chemicals to purchase, and 3) how to use specic chemicals
safely and effectively.
2. Never let chlorine come into direct contact with the pool liner until it has completely dissolved. This means that granular or
tabulated chlorine is rst dissolved in a bucket of water before applying to pool water, and likewise, liquid chlorine is slowly and
evenly poured into pool water from various locations around perimeter of pool.
DANGER: NEVER add water to chemicals. INSTEAD, always add chemicals to water. Also, never mix separate chemicals
together, rather, add chemicals to the pool separately and allow them to circulate throughout the pool before adding additional
types of chemicals.
3.We recommend that you purchase a test kit, and frequently test your pool water to make sure that your PH balance and
chlorine levels are optimal. Your local pool supply retailer can provide information on purchasing and using a test kit that is
most suitable for your needs. NOTE: Excessive chlorine levels or low (acidic) pH levels can damage your pool liner, so please
take corrective action as soon as possible if testing reveals either condition.
The tasks of removing larger debris from your pool and keeping the inside of the pool liner clean are simplied by using a
Prompt Set Pool Maintenance Kit, which includes a leaf skimmer and garden hose powered vacuum. Maintenance Kits are
included as a bonus feature in larger pool systems, and can also be purchased separately as an accessory.Please contact
WARNING:
If applicable, the lter pump included with your pool is designed to remove dirt and
other small particles from your pool water. However, to maintain pool water that is perfectly clear, algae
free, and safe from harmful bacteria, it is VERY IMPORTANT TO ENGAGE IN A CONSISTENT REGIMEN
OF CHEMICAL TREATMENT. Contact your local pool supply retailer for guidance on the safe and effec-
tive use of chlorine, shock, algaecide and other such chemicals.
WARNING:
To avoid skin and eye irritation or even injury to bathers, never add chemicals to the
pool while it is occupied. Never add any chemicals or substances to your pool if you cannot verify the
exact quantity or type to add to the water. Consult a pool supply retailer for specic instructions and
guidelines concerning the use of chemicals in your pool.
WARNING:
It is highly recommended that pool owners frequently test their pool water to ensure
that the pH and chlorine concentration in the water is optimal for safe and enjoyable bathing throughout
the season. Please consult your pool supply retailer to nd a suitable testing kit and instructions on its
use.
WARNING:
Non-respect of the maintenance rules may result in serious hazards for health and
especially for the children.
1312
SRP-14-GB(V3)
PART7-IN-SEASON POOL
MAINTENANCE AND WATER CARE
your local after sale service center if you want to get advice on any repair during the life of the pool kit.
4. If applicable, check your lter-pump cartridge every two weeks (or more frequently during periods of heavy usage) to verify
whether it needs to be cleaned or replaced. If your cartridge is no longer white in color, attempt to spray it clean with a strong
blast of water from your garden hose. If your cartridge cannot be cleaned in this manner, the cartridge must be replaced. Failure
to frequently clean and/or replace your cartridges will affect the effectiveness of your lter pump and could shorten its useful life.
5. If your pool system included a cover, try to keep your pool covered at all times when not in use. This will help keep the wind
and other elements from depositing dirt and debris in your pool, and will also prevent excess rainwater from overlling your pool.
6. Remind your family and friends to always hose or rinse off any dirt or tanning oil from their hands, feet, and body prior to
entering the pool.
7. It’s necessary to monitor the bolts and hardware of the pool (eg. rust stain) when possible.
8. Once your pool has been lled with water for the season, take note if your pool becomes overlled due to rainwater or ac-
cidental overll. If this should occur, it is important to drain or bale out the excess water as soon as possible. If it is an inatable
ring pool, the water level should never be higher than the bottom edge of the inatable ring.
PART8-TROUBLE SHOOTING
PROBLEM DESCRIPTION CAUSE REMEDY
COLORED
WATER
• Water turns blue, brown, or black
when first treated with chlorine.
• The chlorine is oxidizing minerals
in your water. This commonly occurs
with water from different sources.
• Adjust pH to recommended level.
• Run filter until water is clear.
• Regularly clean cartridge.
PARTICALS
SUSPENDED
IN WATER
• Water looks “milky” or cloudy. • “Hard Water” caused by an elevat-
ed pH.
• Chlorination is inadequate.
• Foreign debris in water.
• Bathers are not cleaning their feet
prior to entering pool.
• Adjust pH. Check with a swimming
pool supply retailer for correct water
treatment.
• Ensure proper chlorine level.
• Clean or replace your filter.
• Spray off dirt with a high-pressure
hose before entry.
PERSISTENT
LOW WATER
LEVEL
• Pool appears to be losing water on
a daily basis.
• Tear or hole in pool liner.
• Tear or hole in a filter pump hose.
• Hose clamps are too loose.
• Evaporation from high summer
temperatures.
• Locate damage and repair with the
included patch kit.
• Repair or replace hoses.
• Tighten all hose clamps.
• Keep pool covered when not in
use.
ALGAE
• Water has greenish tint.
• Green, brown or black spots
appear on pool liner.
• Pool bottom is slippery and/or an
unpleasant odor is present.
• Algae is present. • Apply “shock” treatment (super-
chlorinator). Check pH and adjust to
an appropriate level per your local
pool supply retailer.
• Vacuum or lightly scrub pool liner.
• Test water often to maintain proper
chlorine levels.
POOL
WATER
IS COOL
• Water is not warming to a comfort-
able swimming temperature.
• Pool was set up in an excessively
shady or tree lined area.
• Heat is escaping from pool water.
• Relocate pool to a more open
location where it can get maximum
exposure to sunlight during peak
daylight hours.
• Keep your pool covered whenever
it is not in use.
PB14
SRP-14-GB(V3)
PART9-LIMITED WARRANTY
Model Size Water Capacity Pump Ladder
JL016101NG/NF/NN/ND/NC
8,5’x6’x26” (2.58mx1.79mx66 cm) 690Gal(2612L) ×
JL016101N
8,5’x6’x26” (2.58mx1.79mx66 cm) 690Gal(2612L) × ×
JL016102NG/NF/NN/ND
10’x6,8’x27,6” (3mx2.07mx70 cm) 978Gal(3701L) ×
JL016102N/NV01
10’x6,8’x27,6” (3mx2.07mx70 cm) 978Gal(3701L) × ×
JL017441NG/NF/NN/ND/NC
10’x6,8’x27,6” (3mx2.07mx70 cm) 978Gal(3701L) ×
JL017441N
10’x6,8’x27,6” (3mx2.07mx70 cm) 978Gal(3701L) × ×
JL016103NG/NF/NN/ND
13’x6,8’x31,5” (3.94mx2.07mx80 cm) 1608Gal(6075L) ×
JL016103N
13’x6,8’x31,5” (3.94mx2.07mx80 cm) 1608Gal(6075L) × ×
JL016103-1NG/NF/NN/ND
13’x6,8’x31,5” (3.94mx2.07mx80 cm) 1608Gal(6075L)
JL017442NG/NF/NN/ND/NC
13’x6,8’x31,5” (3.94mx2.07mx80 cm) 1608Gal(6075L) ×
JL017442N
13’x6,8’x31,5” (3.94mx2.07mx80 cm) 1608Gal(6075L) × ×
JL017012N
74”x50”x16,5”(1.88mx1.27mx42 cm) 298Gal(1125L) × ×
JL017013N
90”x62,6”x16,5”(2.28mx1.59mx42 cm) 340Gal(1287L) × ×
We warrant all components contained in this Prompt Set™ Pool/SPA Pool (excluding the lter pump unit) against defects in
materials and workmanship under normal use and service, for a period of 90days from the date of purchase for the original
owner only.
If any of the components have been consumer-replaced, damaged, or misused, the corresponding warranty on those compo-
nents is invalidated. In this situation, you will be advised of the cost of replacement parts and processing instructions.
If a veriable manufacturing defect is found during the relevant time period, we agree to repair or replace at its option any
product under warranty provided proper proof of purchase is presented.
This limited warranty is not valid if the product is used for commercial purposes, or if the damage is caused by an accident, an
act of God, consumer misuse, neglect or abuse, vandalism, improper use of chemicals, exposure to extreme weather condi-
tions or negligence during product set up or disassembly.
We cannot be held responsible for the cost of installation, labor, or transportation expenses incurred due to the replacement of
defective parts. This limited warranty, furthermore, does not cover any unauthorized alterations to the product.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jilong Steel frame 258x179x66 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jilong Steel frame 258x179x66 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info