603247
32
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
32
DE FR ENEN
Dis
p
la
y
dAtnetnoc eht teS
j
ustment ran
g
e The default value
AdJ
temperature correction
-5 ~ 5
-2.5
It is used to correcttheerror,the measured values thesensor
. When you set it, the LCD displays the correction
value. After three seconds, the LCD displays the measured value after correction.
PrG
2+57 / 1+6 / 2+5edom emit-doirep ehT
5+2Monday to Friday to set the same and Saturday to Sunday to set the same
6+1Monday to Saturday to set the same, Sunday is independent
7Monday to Sunday is same setting value.
LtP
FFOelbasiD :FFO / elbanE :nOezeerfitnA
Low temperature protection, what is suitable for the water system To prevent the pipe at low temperature was
freezing.
Sen
Sensor or temperature control mode I
N: Built-in OUT: External
ALL: Dual temperature control
IN
IN internal control, room sensor Out external control, floor sensor ALL double temperature double
control, the internal room temperature sensor, external sensor overheating protecting
tOP
External temperature sensor limit
40-80 50
The sensor is set to ALL, the temperature limit external sensor value
dt0
Internal sensor hysteresis
0.5-4 1
Built-in temperature sensor hysteresis
dt1
External sensor hysteresis
0.5-5
3
External temperature sensor hysteresis
bL
no syawlA :nOsutats gnithgilkcaB
OFF Auto turn off after 5sec
OFF
Backlight lighting mode, can be set according to personal preference
Sat
emit yreve ta sutats ffo :FFOrewop-er ta sutatS
On: the same as previous,
OFF
Used to control the power state o
f the boot
deF
Restore factory settings Restore factory settings To restore the default settings
the error and solution of Common system
1. Nodisplay
Power supply system is having problems or power is supplied incorrectly, please check
if the inlet wire is normal.
If the connection is not right, please wired up as the wiring diagram on the back side.
The thermostat of the working environment temperature is too low, please note the
thermostat temperature range.
If the temperature is lower than -5 °C, the thermostat cannot normally display.
Power supply box and the motherboard Coupling is not connected correctly, please
connect correctly.
Power supply box and the motherboard Coupling is opposite inserted, please mind
the direction
Power supply box and the motherboard Coupling is broken, please don‘t overexert.
Coupling length is 6cm,
the installation must be careful. If damaged, no replacement.
correct the error, the sensor
,setting item
protect
from
temperature control mode at different
sensor setting
IN: temperature control mode at different sensor setting OUT: control by oor sensor, only with external sensor
ALL: Dual temperature control, the heater stop when room temperature > setting value or oor temperature > setting value (tOP)
oor-temperature‘s limited value
oor-temperature limited value with ALL mode (Sen)
value
value
value
value
bootstatus when boot
boot status, off status or continue previous status
32

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Jago-RMTMS01

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jago RMTMS01 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jago RMTMS01 in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 1,89 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info