555003
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Klávesnice KB-350 Antivandal 4 / 4 MEV51303 Klávesnice KB-350 Antivandal 1 / 4 MEV51303
Reset
If the master code or service code is forgotten or if you connect a new keypad, it is necessary to reset the
control unit. Disconnect power and connect the RESET jumper and after 20sec. reconnect power. After 5
seconds, disconnect the jumper. This procedure will restore the factory default settings (master code = 1234,
service code = 9999, all user codes are erased) and it will also enroll connected keypads to the control unit.
output control
PANIC mode
factory setting:
MC 1234
UC1-UC9 deleted
Code setting
setting deleting
save and exit
save and exit
MC master code
UC1-UC9 user codes
operating
mode
Parameters setting
Output N.1 mode
Output N.2 mode
Panic mode
Number of attempts
Tamper output reaction
New Service Code
values
default
00- latch
xx- pulse (01-99 sec)
0=off, 1=on
0=off, 1=on
1-9 or 0=unlimited
must be entered 2x
Note: Although this product does not contain any harmful materials we suggest you to return the product to
the dealer or directly to the producer after usage.
KB-350M Digital Access Keypad
The KB-350M access control keypad can operate electric devices such as door locks, gates, or security
systems. It consists of two parts - a keypad and a control unit. Both parts are connected by a two-core
cable. One or two keypads can be wired to each control unit (e.g. they can be installed on both sides of a
single door). While one keypad is being accessed, the second keypad is temporarily bypassed.
A separated control unit insures maximum security. The communication in the cable from the keypad to
the control unit is encrypted with a sophisticated floating code protocol. This ensures that there is no other
way to operate the device than by entering a valid access code.
The keypad itself is made of a solid alloy and it is suitable for vandal proof applications.
Specifications
Power 10 – 16 V AC or DC, 60mA no relay on, 120 mA both relays on
Keypad connecting cable 2 core cable, max. 100 m, arbitrary polarity
Output relay (output 1) over-switching contact 1 A / 60 V
Transistor output (output 2) switches to GND – max. current 1.5 A / 25 V
Tamper output max. 100 mA / 25 V (control unit, keypad and cable tamper protection)
Power output rectified voltage from PWR input terminals - max. 1.2 A for max. 5 sec
Access codes 4, 5 or 6 digits, 1 master + 9 user codes (each code can be addressed to output 1
or 2)
Output modes programmable duration of pulse (from 1 to 99 sec.) or latch mode
Number of attempts programmable
Security grade 3 midle to high risk (EN 50131-1)
Keypad working environment outdoor use (class III), -25 °C to 50 °C (EN 50131-1)
Enclosure IP52 (EN 60529), mech. resistance IK08 (EN 50102)
Control unit working envir. indoor – general (class II), -10 °C to +40 °C (EN 50131-1)
Complies with the essential requirements of: 89/336/EC EMC Directive - Protection concerning electromagnetic
compatibility when is used for its intended purpose. Original of the conformity assessment can be found
at the web page www.jablotron.cz, section Technical support.
Installation
Keypad can be installed on a standard electro installation box (screw spacing - 60 mm).
remove front panel - use the provided tool to unscrew the 4 screws
connect the keypad’s terminals with the control unit’s BUS terminals using two wires (twisted pair) (e.g.
SYKFY cable), max. distance – 100 m, arbitrary polarity
up to 2 keypads can be wired in parallel, the total length of all cables should not exceed 100 m
reattach the keypad after powering and testing (see bellow)
Note, if you change or add a keypad, you must reset the control unit!
Control unit can be installed directly on a wall or on an installation box. Terminal descriptions follow:
C, NC, NO over-switching relay contact (output N.1), max. 1 A / 60 V, (C=common, NC=normally closed,
NO=normally opened)
TMP, TMP NC tamper output, max. 0.1 A / 25 V; opens when a control unit is opened, if any keypad is
lost, if the connecting cable is cut or shortened or if a pre-programmed number of attempts to
enter the correct code is exceeded or if a panic sequence is entered (programmable)
OUT transistor output (output N.2), max. 1.5 A / 25 V. It switches to GND when activated.
+E rectified power voltage (from PWR input terminals). It can be used for the powering of an
electric door lock etc. Maximum permanent load is 0.25 A, short period load (max. 5 sec.) -
can be 1.2 A (for electric strike release). Note that a corresponding power supply must be
used to power the unit (RWR terminals).
GND ground terminal of internal power supply
BUS, BUS bus line terminals for keypad connection. Up to 2 keypads can be connected in parallel. Twist
pair (e.g. SYKFY) is recommended, max. length – 100 m. Polarity is arbitrary. The bus is used
for both powering the keypads and for data transfer (a highly secure floating code is used).
Note, if you change keypads, you must reset the control unit.
Klávesnice KB-350 Antivandal 2 / 4 MEV51303 Klávesnice KB-350 Antivandal 3 / 4 MEV51303
PWR, PWR power supply input (10 - 16 V AC or DC). Adapter
DE20-15 or backup power supply BP-12 are
recommended.
LED indicators on the control unit:
green output relay is triggered (output N.1)
red output transistor is triggered (output N.2)
yellow tamper is triggered (TMP)
LED indicators on the keypad:
green output relay is triggered (output N.1)
red output transistor is triggered (output N.2)
yellow both output N.1 and N.2 are triggered
green flashing programming mode
red flashing keypad is bypassed (the other one is being
used or a number of attempts to enter the
code was exceeded)
First powering
Connect the RESET jumper in the control unit and switch on the power supply. After 5 seconds, disconnect
the jumper. This procedure will enroll all of the keypads into the control unit. Test the keypads by entering the
factory default code 1234. If everything is operating correctly, the green LED on the keypad should switch on.
Leave the RESET jumper disconnected.
Access codes setting
10 different access codes can be used. One code is a master code which can operate the keypad as well
as set the other user codes. The factory default master code is 1234, the other user codes are blank. All
access codes can have 4,5 or 6 digits and a corresponding output (N.1 or N.2) can be assigned to each
code.
Enter: 5 master code (default 1234) first. The green LED will start flashing (programming mode).
Master code setting:
0 xx...x xx...x y
where xx...x is a new code (4 to 6 digits), after pressing it is necessary to reenter the new code
y enter 1 or 2 to assign a corresponding output
User codes setting:
A xx...x y
where A is a user code number (from 1 to 9)
xx...x is a new user code (4, 5 or 6 digits)
y enter 1 or 2 to assign a corresponding output
User code deleting:
A where A is a code number (1 to 9)
To exit the code setting mode press the key. If you press the # key, none of the codes entered in the
current session will be stored in the memory.
Optional parameters setting
Enter: 6 service code (default 9999) in order to enter the parameters programming mode. The green
LED will start flashing.
Working mode of output N.1 (relay):
1 xx
where xx is a period of time during which the relay is switched on (01 – 99 sec.). If 00 is entered, then the
output N.1 will be set to a latch mode (it changes its status whenever a valid assigned code is entered)
Operating mode of output N.2 (transistor):
2 xx
where xx is a period of time during which the relay is switched on (01 – 99 sec.). If 00 is selected, then the
output N.2 will be set to a latch mode (it changes its status whenever a valid assigned code is entered)
Panic (access under duress 7 is pressed before a valid code):
3 x
where x can be 0 = off, 1 = on (if 7 is pressed before a valid code, the TMP output is triggered for 3
seconds simultaneously with the associated output reaction)
Number of attempts to enter an access code:
4 x
where x is the maximum number of attempts (0 = no check). If this number is exceeded, the keypad is
blocked for two minutes (can be overridden with a repeated entry of a valid code). The TMP output can
also be triggered (see following setting).
TMP output reaction if a number of attempts to enter a code has been exceeded:
5 x
where x can be 0 = no reaction, 1 = triggered for 3 sec.
New service code setting:
6 xx...x xx...x
where xx...x is a new service code (4, 5 or 6 digits), code must be repeated after pressing
To exit the programming mode press the key. If you press the # key, programming will not be stored.
DE20-15 adapter
230V/50Hz
Bus line length- max. 100 m
electric strike
(Z8-12V)
electric strike
(Z8-12V)
tamper
Example two doors access control. AC or DC power supply may be used. Pulse length on outputs N.1 and
N.2 should be set to 1 – 5 sec. (depending on the type of electric lock). Garage gates, parking bars etc.
can be controlled in a similar way.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron KB-350M bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron KB-350M in de taal/talen: Engels als bijlage per email.

De handleiding is 0,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info