631258
7
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
The JA-82Y GSM communicator installers manual 7/7 MDL51108
7.10. URL / IP address for data transmission
The communicator supports transmission of special data (e.g. visual information
from JA-84P) from the system to a set IP address, which can be set by the
following sequence:
013 xx..x0
where:
xxx...x is the IP address and port – entry format example:
013 8 192 168 021 123 07070 0
Where
8 (auto-converts to #) signifies an IP address which must have 12
digits and must be followed by the 5 digits of the port number (no
separators).
To erase the IP enter 0130.
Notes:
if no devices supporting this feature are in the system, do not set any IP
address.
the address can also be entered in URL format through OLink, the system
keyboard allows digits only
Factory default setting: URL - lib1.jablotron.cz:7070
7.11. Locking the ARC settings
All settings which affect reporting to ARCs can be locked by a digital code. To do
so, enter:
091 xx..x*0
where:
xx..x is your code (4 to 8 digits)
Notes:
Exiting service mode after the locking code has been entered will lock all the
settings affecting ARC communication (see the sequence list in section 13).
If ARC programming is locked, then it can be temporally enabled in service
mode by entering 092 xx..x
0 where xx..x is the locking code. It will then
relock on exiting service mode.
The ARC settings can be permanently unlocked by entering 091
0 (the code
can be erased only if ARC setting is unlocked)
Factory default setting: ARC settings unlocked
7.12. Repeated ARC communication
The communicator tries to send the report to the main telephone number. If this
fails, it tries the backup number and in the case of failure, the communicator
repeats the attempt with a delay which is set by the following sequence:
0001 p mmss
where:
p 1=ARC1, 2=ARC2
mmss time in minutes, seconds
Factory default setting: 15s
7.13. Number of repeated attempts
Defines how many times in a row the communicator will try to transmit
information to the ARC after an unsuccessful attempt. It is possible to set up to 9
repeated attempts. They are set by the following sequence:
0002 p n
where:
p 1=ARC1, 2=ARC2
n 1 to 9 attempts
Factory default setting: 2 attempts
7.14. Integrated image transmission module
The communicator contains a built-in module for the reception of images from JA-
84P detectors. The device must be set up properly for the successful transfer of
photographs to the server (see 7.10) The Jablotron image viewing server is
situated at http://img.jablotron.com.
IP address for image sending:
URL: lib1.jablotron.cz:7070 IP: 77.104.220.129:7070
Warning: The set or modified parameters only take effect after you exit service
mode.
The signalling of image transmission on the module
Once the images have been taken by a JA-84P, they are immediately sent to
the GSM communicator and subsequently to a secure server (if it has been
set).
The transmission from a PIR to the communicator is indicated by green LED 1
being permanently lit (on the left under the SIM card holder) see fig. 1
Communicator description:.
Transmission to the server is signalled by a flashing green LED.
Successful transmission is confirmed by a long green-LED flash and
unsuccessful transmission is reported by rapid flashes of the green LED.
Successful transmission from the GSM communicator to the server is
confirmed by a long flash of the red LED, unsuccessful transmission is reported
by flashing of the red LED.
Notes:
The total time of transmission to the server is about 20s.
If the signal is weak, the transmission can take longer (the lost data is sent
repeatedly). Each image contains the date and time of acquisition which is
taken from the control panel internal clock.
The synchronization of time from the moment the batteries are inserted into a
JA-84P takes 60 minutes.
7.15. Updating the communicator
The communicator can be updated by any authorized person. (i.e.firmware,
language and voice settings). Current firmware is accessible on
www.jablotron.com. Before updating, save your communicator settings to the
OLink database. For updating, it is necessary to have one of these interfaces: JA-
80T, JA-80BT or JA-82T and the program OLink (v.2.0 or higher). Uploading via a
JA-82T is faster. Be careful not to do anything during the updating process (don´t
disconnect the cable or do anything with the PC) and wait till the end.
Restart the communicator after the updating procedure via the 893 sequence, or
turn off the main power and battery and after a few seconds turn them on again.
Then wait for 1 minute. During this operation do nothing with the system till the red
LED stops shining.
Updating can change the device registration key which you need for remote
access via the internet.
8. Further guidance on the communicator
8.1. How the communicator sends reports
1. If there is a need to report an event (e.g. an alarm) then the
communicator sends data to ARC1 (the communicator tries the main
phone number / IP address / URL. If unsuccessful then it tries the
backup number / IP address / URL and if still unsuccessful, it repeats
the action).
2. Then it sends data to ARC2 in the same way if programmed as an
independent ARC. If ARC2 is programmed as the backup to ARC,1
then the data will only be sent to it if transfer to ARC1 has been
unsuccessful.
3. Then the unit sends SMS reports (1st tel. number, 2nd tel. Number,..)
4. Then the unit transmits a voice message to each telephone number
with this setting. Each programmed number is called only once
regardless of whether the call has been answered or not. Pressing the
# key cancels calling other numbers and the system enters keypad
simulation mode in which it is possible to fully control the system.
If all previous attempts to send data to ARCs have been unsuccessful, the next
attempts occur after the programmed repeat period (see 7.6).
If an alarm is cancelled by a user while it is being reported, any unsent
SMSes and unperformed call reports are cancelled, but the ARC still gets a
complete set of reports about events in the system.
8.2. The communicator’s LED
The red LED on the communicator board indicates as follows:
It is lit for a period during registration to a GSM network
when sending an SMS message, the LED is lit for 1 second
the LED flashes rapidly during the detection of an incoming call
It is lit permanently during remote access from a telephone
A permanently lit LED could indicate that the communicator is not registered
to a GSM network
The LED flashes during remote-access data transfer
The green LED on communicator board indicates as follows:
Flashes for a 2 seconds when communicator is connected to control
panel
Flashes once a second when pictures are transmitted (see 7.14)
8.3. Notes on entering service mode
If the system is switched to service mode:
1. The communicator completes the current transmission to the ARC.
2. The current phone call reporting is terminated.
3. Unfinished SMS and call reports are erased (they are not transmitted
after the service has finished).
4. Unsent ARC reports are only erased if ARC tel. numbers / IP
addresses / URLs or the ARC communication format or the installation
ID are changed.
5. Fault restoration reports are sent to the ARC even in service mode.
6. Changes to communicator settings do not take effect until service
mode has been exited.
8.4. Remote access via the Internet
The system can be accessed remotely via OLink 2.0.1 and higher. This allows
complete programming by installers (it is necessary to know the service code) and
also operating the system by end users in the same way as if they were using a
keypad. To access the system remotely it is necessary to have:
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-82Y GSM communicator bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-82Y GSM communicator in de taal/talen: Engels als bijlage per email.

De handleiding is 0,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Jablotron JA-82Y GSM communicator

Jablotron JA-82Y GSM communicator Gebruiksaanwijzing - English - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info