631258
4
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
The JA-82Y GSM communicator installers manual 4/4 MDL51108
6.10. Quick enabling / disabling of reporting to phones
Event reports to your phone can be enabled / disabled as follows:
901 0 all SMS and call reports disabled
901 1 all SMS and call reports enabled
901 2 all reports enabled except reports of setting and unsetting by
users 41 to 50 (i.e. their codes, cards and key fobs). Master code
control is not reported either. This allows setting and unsetting done by
report recipients (owners, bosses, etc.) not to be reported.
Factory default setting: 9011 all reports enabled
6.11. Enabling remote access
The following sequence enables remote access to the system by phone or
Internet:
802 0 remote access completely disabled
802 1 access from any telephone and Internet access via OLink enabled
802 2 access from programmed phones and Internet access via OLink
enabled
Factory default setting: Remote access enabled
6.12. Forwarding of incoming SMS messages
The communicator enables the automatic forwarding of incoming SMS messages
which contain no valid instructions to the system:
801 0 messages are not forwarded, but the communicator saves the last
10 received messages to the SIM card
801 1 messages are forwarded to the first programmed tel. number in
memories M1 to M8 (e.g. if numbers are only programmed in M5
and M6, then messages will be forwarded to M5). The tel. number
from which the SMS was received will be shown at the beginning of the
forwarded text.
Factory default setting: messages are forwarded
Note:
In order to protect the user against runaway (donation SMSes etc.), the
forwarding is limited to the first 50 SMS messages. The counter can be erased
automatically each midnight, by processing any SMS instruction or by exiting
Service / Maintenance mode.
6.13. Automatic GPRS configuration
If the communicator detects a SIM card change and the main power is on, it sends
an SMS to the YTUN Jablotron server with the network identification. The server
sends back : APN, login, password and own SIM card telephone number.
903 0 auto configuration disabled
903 1 auto configuration enabled
Factory default setting: auto configuration enabled
6.14. SMS instruction confirmation
If the communicator receives a valid SMS instruction, a confirmation SMS will be
sent a s a reply. This confirmation can be disabled as follows:
904 0 disabled
904 1 enabled
Factory default setting: enabled
6.15. Reaction to incoming calls
This sequence can be used to set the communicator’s reaction to incoming phone
calls:
905 0 the communicator ignores incoming calls
905 1 the communicator will answer after ringing for 15s
Factory default setting: answer after ringing for 15s
6.16. GSM signal dropout indication
This feature enables the monitoring of GSM network signal availability. If enabled
and if there is a GSM signal dropout longer than 15 minutes, the control panel
announces “External communication fault”.
906 0 signal availability monitoring disabled
906 1 signal availability monitoring enabled
Factory default setting: disabled
6.17. Time synchronization via SMS
This setting enables the function for synchronizing the clock in the control panel.
See chapter 8.5 for further details.
907 0 synchronization off
907 1 synchronization on
Factory default settings: on
6.18. Phone receiver loudness
To set the loudness of the receiver of the phone which is used to call the
communicator key in:
909 x where x is a number from 1 to 9 (max.)
Factory default setting: 9 (max.)
6.19. Number to be called to maintain SIM card validity
If a prepaid SIM card is used and a lack of outgoing phone calls for a certain period
cancels the validity of the SIM card, then this function offers the following: if there
have been no outgoing phone calls within the last 90 days, then the communicator
automatically calls the number programmed by this sequence. The communicator
waits until the call is answered and then automatically hangs up after 10 sec.
910 xx...x 0
where: xx...x is the telephone number
Notes:
To erase this number enter 910 *0
It is recommended to call cheap public services (e.g. weather forecasts etc.)
but not toll-free numbers.
Factory default setting: Erased
6.20. Restriction of the number of sent SMSes
The parameter limits the amount of sent SMSes to 100 per 24 hours. 50 may be
alarm SMSes and 50 may be for other events. This is to prevent enormously high
telephone fees.
803 0 restriction disabled
803 1 restriction enabled
Factory default setting: enabled
6.21. Prepaid SIM card credit interrogation
The communicator is capable of checking the credit balance of its SIM card upon
request (by “CREDIT” SMS instruction) or this activity can be requested
automatically (with a preset cycle) and if it finds out that the remaining credit is
lower than the preset value, an information SMS is sent. The function is set by
sending the following SMS instruction:
code_CREDIT_uu..u_xx_yyy_zz
where:
Code valid access or service system code (e.g. 8080 or 1234), the change of
parameters is possible on with a service code (other codes allow SMS credit
interrogation “1234 CREDIT“)
_ space
uu..u instruction recognized by the GSM network to check the balance
xx automatic checking period in days,
yyy minimum acceptable credit balance
zz the textual position in which the number showing the balance starts in
the reply message from the GSM provider.
Notes:
If the reported credit balance is lower than the set limit (yyy), text no. 545 will be
sent to phone numbers M1 and M8 which have the “Low credit balance” (event
no. 50) event sending enabled
If only uu..u follows the CREDIT instruction (no xx yyy zz) then periodic balance
checking will not be performed, but the balance will be checked immediately
If there is further data following the CREDIT instruction, the communicator will
memorize them and automatically put them in the message when the CREDIT
instruction is used again (i.e. the Credit instruction must contain at least the
uu..u part upon the first sending) and the user just needs to send: code
CREDIT
Example: sending the SMS instruction “code CREDIT
101# 7 50 1” causes the
credit balance to be checked every 7th day after the SMS has been sent and if the
balance (starting with the first character in the message from the GSM provider) is
lower than 50 currency units it will be reported.
Warning: the use of prepaid SIM cards in the communicator can negatively
influence the reliability of the device. Some GSM providers block cards not
only when there is no credit but also when they are not topped up frequently
enough. This means that even if there is enough credit balance on the card,
the communication can still be blocked. We therefore strongly advise the
use of tariff SIM cards !!!
6.22. Remote programming by SMS instructions
The communicator enables remote programming of the system by the following
SMS instruction:
code_PRG_seq_seq, another instruction
where:
Code valid access or service system code (e.g. 8080 or 1234)
_ space
seq programming sequence usually set via the keypad
Notes:
Only characters which can be keyed in from the system keypad (0 to 9, * and
#) can be used in the sequences
When a valid instruction is received, the communicator performs the sequence
by simulating entering the keys on the keypad. A comma in the SMS is taken
as a pause in the sequence entering.
If you want to remotely reprogram the system it must first be unset and then
switched to programming mode
The number of sequences in one SMS is limited by the maximum size of the
SMS in the GSM network.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-82Y GSM communicator bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-82Y GSM communicator in de taal/talen: Engels als bijlage per email.

De handleiding is 0,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Jablotron JA-82Y GSM communicator

Jablotron JA-82Y GSM communicator Gebruiksaanwijzing - English - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info