The JA-81F is a component of Jablotron’s OASiS alarm system and is designed to control
and program the system. The display backlight colour can be set according to your needs.
It has a built-in proximity access card reader and allows the wiring up of a separate door
detector. The battery-powered keypad communicates wirelessly using OASiS protocol.
Installation
Installation shall only be undertaken by technicians holding a certificate issued by
an authorized distributor. The keypad is for indoor installation only, typically by the
main entrance door. Avoid locating it close to metal objects, which could shield radio
communication.
1. Open the keypad housing (by pressing the tab on the bottom) using a
screwdriver. The tab is also accessible from the front after opening the key
cover.
1. Install the rear housing to the desired location
2. Install the external hard-wired detector (if required)route its cable through
the rear housing and connect to the IN and GND terminals.
3. Enroll the keypad to the control panel (see the control panel installation
manual) as follows:
• Enter enrollment mode in the control panel (if the system does not have a
keypad already, briefly short the reset link on the control panel main board,
or if a keypad is present, then press key 1 in service mode).
• Install the battery into the keypad to trigger enrollment.
• Exit enrollment mode by pressing the # key.
4. Attach the keypad to the rear housing.
5. Instructions on how to use the keypad can be found in the control panel
operating manual.
Keypad menu
The menu can be entered in Service mode by holding the ? key. Then the internal
keypad menu will be displayed. Using the arrows on keys 1 and 7 you can scroll
through the menu:
Display Key Description
Tamper ON
¾
Disable / Enable the tamper sensor
(only for service purposes)
Door chime ON
¾
Disable / Enable sound when IN triggered
Beeper ON
¾
Disable / Enable system sounds
Backlight colour
Sets the normal display backlight colour 0 - 7
Warning colour
Sets the warning display backlight colour 0 - 7
Brightness
Sets the display brightness 0 - 9
Contrast
Sets the display contrast 0 - 9
Edit text
¾
Entry to keypads text editing
English
¾
Sets English (reload default texts)
Čeština
¾
other languages ...
To exit the menu, press # (exiting also occurs after 60 seconds’ inactivity).
Notes:
• It is possible to set a different colour backlight as a warning colour for when a fault
is indicated or after an alarm state (warning colour). The user can be visually
informed of the status. If unwanted, please set both colours to the same value.
• The menu can be displayed even if the keypad has not been enrolled to the
control panel.
• Each keypad has its own menu, i.e. each keypad in the system can have its own
unique settings.
• The keypad keeps its settings even if its power is disconnected (settings can only
be altered via the keypad menu).
• The menu can also be entered when the ¾ key is kept pressed while the keypad
is being powered-up.
Keypad sleep mode
When battery-powered, the keypad saves energy by turning itself off when the cover is
closed or automatically after 20 seconds of inactivity (15 minutes in service mode). The
keypad is woken up by: opening the keypad‘s flip cover, pressing any key, or triggering
the wired door detector input - see below.
Optional AC adapter
If the keypad is powered by an AC adapter (model: Jablotron DE01-12 for terminals:
+U and GND), it will not turn off after 20 seconds of inactivity. If the adapter is used,
batteries should still be installed. Only turn on the AC adapter after the keypad unit
has been powered up by batteries and the two halves of the housing are back
together.
Note: To comply with EN standards the keypad does not indicate the status of the
alarm system. If desired, the system setting / unsetting status can be programmed in
the control panel to be permanently indicate by the keypad.
Installing a door detector
It is possible to wire up a detector(s) to the keypad. The IN input terminal is triggered when
disconnected from GND. The control panel’s reaction to the IN input being triggered is a
delayed intruder alarm linked to the keypad‘s address. If desired, another reaction can be
programmed in the control panel. The IN input can indicate a door being permanently
open (status reaction). If the IN input is not used then it must be shorted to GND.
123
ABC
456
A
789
ON
0#
B
?
OFF
ESC
ABC
OASiS
IN
GND
+U
Note: The lifetime of the battery is reduced proportionally to how frequently the door
detector is triggered and how often and how long the keypad is battery-powered.
Testing keypad communication
In service mode, the control panel allows you to measure the keypad’s radio signal
strength. To test the keypad signal, trigger either its IN input or its tamper sensor.
Note: the control panel measures the strength of the signal transmitted by the
keypad. It is impossible to measure the signal strength received by the keypad from
the control panel. If the keypad has lost communication with the control panel (e.g. if
the control panel is damaged) it would display COMM ERROR a communication
error. If you re-power a control panel, which previously worked with a keypad, and
the keypad does not function, then we recommend disconnecting the keypad
batteries for one minute.
Controlling the PgX output
The PgX output can be switched ON and OFF by pressing the ON (¾) and OFF (#)
buttons long (for 5 seconds). The function of PgX must be set in the control panel. A
long beep confirms the change of the output’s state.
Keypad text editing
The most convenient way to edit text is to use a PC running OLinksoftware. To
transfer edited text from a PC to the keypad, the keypad (with its batteries installed)
has to be connected either to the OASiS system‘s digital bus (i.e. one cable from the
keypad to the control panel, and another cable from the control panel to the PC) or
directly from the PC. The texts are transferred by choosing the Save menu in the
Texts window in OLink software.
The names can be edited via the keypad in the “Edit Text” menu item – see the
control panel installation manual. The edited text is only stored in the keypad unit
used for editing.
Battery replacement
The system checks the battery status and if discharged it will inform the user or the
installer. The keypad will continue to work but will also indicate a low battery as well
as the backlight being reduced. Batteries should be replaced within one week by a
qualified technician in service mode. If they are not, the keypad is switched off when
the battery power falls under a critical limit.
Note: Both batteries must be always changed together and with
identical types (manufacturer). Please allow one minute delay before
inserting new batteries.
Removing the keypad from the system
If the keypad is removed from the system, the control panel indicates this event. If
you want to uninstall the keypad, it must also be erased in the control panel.
Technical specifications
Power supply 2x lithium batteries type CR123A (3.0V)
Typical battery lifetime approx. 2 years (2 daily activations and no IN usage)
External power supply 12 V DC
Standby consumption 100mA
Communication frequency 868 MHz, OASiS protocol
Communication range approx. 100m (open area)
RFID cards Jablotron PC-01 or PC-02 (EM UNIQUE 125kHz)
Door detector input IN = normally closed loop
Dimensions 120 x 130 x 30 mm
Environment according to EN 50131-1 II. internal
Operating temperature range -10 to +40 °C
EN 50131-1, EN 50131-3, EN 50131-6, EN 50131-5-3 classification 2
Complies with ETSI 300220, ETSI 300330, EN 50130-4,
EN 55022, EN 60950-1
Can be operated according to ERC REC 70-03
JABLOTRON ALARMS a.s. hereby declares that the JA-80Fis in compliance
with the essential requirements and other relevant provisions of Directive
1999/5/ECThe original of the conformity assessment can be found at
www.jablotron.com
, Technical Support section.
Note: Although this product does not contain any harmful materials we
suggest you return the product to the dealer or directly to the producer
after use.
Hulp nodig? Stel uw vraag in het forum
Misbruik melden
Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.
Product:
Spelregels forum
Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:
lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;
Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.
Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.
Abonneren
Abonneer u voor het ontvangen van emails voor uw Jablotron JA-81F-RGB bij:
nieuwe vragen en antwoorden
nieuwe handleidingen
U ontvangt een email met instructies om u voor één of beide opties in te schrijven.
Ontvang uw handleiding per email
Vul uw emailadres in en ontvang de handleiding van Jablotron JA-81F-RGB in de taal/talen: Engels als bijlage per email.
De handleiding is 0,1 mb groot.
U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.
Stel vragen via chat aan uw handleiding
Stel uw vraag over deze PDF
Uw handleiding is per email verstuurd. Controleer uw email
Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.
Er is een email naar u verstuurd om uw inschrijving definitief te maken.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken
U heeft geen emailadres opgegeven
Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.
Uw vraag is op deze pagina toegevoegd
Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.
