alarm siren, a sounder for entrance and exit delay
beeps and a detector-triggered chime. It also
sounds when an intruder alarm has been
triggered and confirms the actual presence of an
intruder in the building by sending a tamper signal
when it gets unplugged.
It can be used as a stand-alone device – as a
wireless doorbell or for calling for help.
In combination with a smoke or gas detector it
will set a two minute warning alarm for fire danger.
Enrolling the JA-80L to an OASiS control panel
1. Switch the control panel to service mode and key in 1 (to enter enrollment mode).
2. Plug the siren into a mains socket. The JA-80L indicator will turn on and off which
confirms enrollment.
3. Exit enrollment mode by pressing the # key on the system keypad.
Notes:
a) Several sirens can be enrolled to the control panel if desired.
b) If the siren fails to enroll (its indicator will not turn off), check:
• Is the control panel in enrollment mode ?
• Is the siren set to factory default settings ? If not, reset the siren.
c) An enrolled siren generates a siren sound if an alarm is triggered in the control
panel, and can generate beeps for entrance and exit delays (programmable in
the control panel).
d) The siren can be simultaneously used as a wireless doorbell or a detector-
triggered chime. To do this the doorbell button and the relevant detectors have to
be enrolled to the siren (after the siren has been enrolled to the control panel –
see later text).
e) If the siren gets unplugged from the mains while sounding an alarm, the siren
immediately sends a tamper signal to trigger a tamper alarm in the control panel.
The siren’s radio signals can be checked and measured by the control panel in
service mode. To make the siren transmit a test signal, press its button.
Additional siren settings
The siren can acoustically signal settingthe system (1 beep) and
unsetting the system (2 beeps). To enable this feature briefly press the siren’s
button three times (confirmed by two beeps). Use the same procedure to
disable the feature (confirmed by one beep).
It is possible to go to other menu levels by holding the siren button (must be
plugged into the mains). When the button is released the state of the currently
chosen setting is changed. Each settable state is
announced by a different
number of beeps.
1. hold for approx. 3s – to change the volume (doorbell melody, chirps), it has
no effect on the sound of alarms
2. hold for approx. 6s – beeps 1x – alarm restricted to PGX – the siren sounds
when the control panel is in alarm state and the PGX output is active
3. hold for approx. 9s – beeps 2x – alarm restricted to PGY - the siren sounds
when the control panel is in alarm state and the PGY output is active
4. hold for approx. 12s – beeps 3x – the LowBAT signal will be transmitted to
the control panel every time when the siren is disconnected from the mains
5. holding the button longer will exit the setting and it will be confirmed by a
long and then a short beep.
An alarm restricted to the PGX or PGY outputs is suitable for a split system
where PGX will be assigned to alarm A and PGY to alarm B.
Enrolling a doorbell button to the JA-80L siren.
Up to 8 wireless buttons of the type RC-8x can be enrolled to the siren as follows:
1. Plug the siren into a mains socket and if its indicator starts flashing, then enrolling
devices to the siren can begin. In this case, the siren still has factory-default
settings, i.e. no devices have been enrolled yet. If the indicator is continuously lit
after the siren is plugged in, then press and hold it (while it is lit) until it starts
flashing. This means that something has already been previously enrolled and
the mode being opened now is for adding more devices.
2. An RC-8x can be enrolled by activating it (pressing its button). Successful
enrollment is confirmed by a melody sound. By activating the RC-8x repeatedly,
you can scroll through the 8 possible melodies which can be linked to RC-8x
activation.
3. If all the desired RC-8x units have been enrolled, exit the siren’s enrollment mode
by pressing its button. This method allows the buttons to be added to the
previously enrolled devices
Detector- triggered chime mode
If it is desired to indicate the triggering of a wireless JA-8x detector by a chime
sound, then enroll the detector to the siren as follows:
1. Plug the siren into a mains socket. If its indicator starts flashing, detector
enrollment can proceed immediately (no previously enrolled devices).
If however, the indicator lights continuously, press and hold the siren button
(while it is lit) until it starts flashing (devices previously enrolled).
2. To enroll a detector, press and release its tamper switch. A sound is then
heard (by pressing and releasing the tamper switch you can scroll through the
8 possible melodies for linking to the detector).
3. After all the desired detectors have been enrolled, exit enrollment mode by
pressing the siren button.
In addition to chime sounds being activated by detector triggering, they can also
be activated by a JA-80F keypad’s IN input being triggered (to enroll a keypad,
press and release its tamper switch).
Alarm siren for wireless fire detectors
If you want to use a JA-80L siren for transmitting an alarm from a wireless
fire detector (JA-80S and JA-80G), enroll the detector to the siren as follows:
1. Insert the siren into the wall socket. When it starts to flash you can enroll the
detector to it immediately (no device was previously enrolled to the siren)
If the light lights constantly, press and hold the button till the light
starts to flash. (some devices are already enrolled to the siren)
2. Enroll the detector by inserting batteries into the detector – the siren
will play the sound of a doorbell
3. After you have enrolled all detectors press the siren‘s button to exit enrolling
mode.
4. When testing a detector by pressing the test button the siren plays a
melody. Never use an open fire to test the detector anywhere indoors. To
test using smoke use a special testing aerosol. The siren sounds when
testing using a test aerosol.
NOTE: If you want to use a JA-80L siren to sound an alarm signal from
wireless detectors, the siren can’t be used with an OASiS control panel at the
same time – it must be used separately.
Maximum number of enrolled devices
Up to 8 RC-8x units or detectors, and a single OASiS JA-80 control panel
can be enrolled to a single JA-80L siren. Each one of these things can be
enrolled to as many sirens or other receivers as desired.
Deleting all enrolled devices (RESET)
All enrolled devices can be deleted as follows:
1. Unplug the siren from the mains socket.
2. Press and hold the siren button while plugging in the siren again.
3. Keep the button pressed until two beeps are heard which confirm a reset.
4. The indicator keeps flashing (device enrollment mode).
5. To exit enrollment mode, press the siren button (indicator turns off).
If the indicator fails to flash after the two reset beeps, it means that the siren is
within radio range of the control panel to which it has been previously enrolled.
In such a case, all devices previously enrolled to the siren have been deleted
except for the control panel. If you deliberately do not want to use the siren with
the control panel anymore, it must first be deleted in the control panel before
resetting the siren (in control panel enrollment mode select the siren’s address
and press and hold key 2 on the system keypad to delete the siren).
Indicator functions
In normal use, the indicator flashes when the doorbell button is pressed or
when the siren sounds. If the siren is enrolled to an OASiS control panel, then it
indicates the status of the programmable output PGY with a continuous light.
The indicator flashes in enrollment mode.
Technical specifications
Power supply 230V/50Hz, 1W, class protection II
Communication band 868 MHz, OASiS protocol
Communication range approx. 100 m (open area)
Sounds (melodies) 8 selectable for buttons and detectors,
and an alarm siren sound 95 dB / 1 m
Max. number of enrolled devices 1x OASiS JA-80 control panel
8x OASiS wireless buttons and detectors
Operating environment general, indoor –10 to +40 °C
Dimensions, weight 90 x 64 x 80 mm, 110 g
Housing IP40 according to EN 60529
Mechanical immunity IK08 according to EN 50102
Operating conditions ERC REC 70-03
The JA-80L complies with ETSI EN 300220, EN 50130-4, EN 55022 and EN 60950-1
JABLOTRON ALARMS a.s. hereby declares that the JA-80Lis in compliance with
the essential requirements and other relevant provisions of Directive 99/5/EC. The
original of the conformity assessment can be found at www.jablotron.com
Technical
Support section
Note: Although this product does not contain any
harmful materials we suggest you return the product
to the dealer or directly to the producer after use.
Hulp nodig? Stel uw vraag in het forum
Misbruik melden
Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.
Product:
Spelregels forum
Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:
lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;
Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.
Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.
Abonneren
Abonneer u voor het ontvangen van emails voor uw Jablotron JA-80L bij:
nieuwe vragen en antwoorden
nieuwe handleidingen
U ontvangt een email met instructies om u voor één of beide opties in te schrijven.
Ontvang uw handleiding per email
Vul uw emailadres in en ontvang de handleiding van Jablotron JA-80L in de taal/talen: Engels als bijlage per email.
De handleiding is 0,08 mb groot.
U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.
Stel vragen via chat aan uw handleiding
Stel uw vraag over deze PDF
Uw handleiding is per email verstuurd. Controleer uw email
Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.
Er is een email naar u verstuurd om uw inschrijving definitief te maken.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken
U heeft geen emailadres opgegeven
Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.
Uw vraag is op deze pagina toegevoegd
Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.
