Handleiding Jablotron JA-80K (pagina 10 van 22) (Engels)

554835

Verklein

Vergroot

Pagina terug

1/22

Pagina verder

Installation manual: Oasis security system JA-80K - 10 - MKE51801

Device reactions and section assignment

(detectors,

key fobs, control panel and keypad inputs)

• A detector’s natural reaction can be INS, DEL or Fire

(selectable in the detector)

• The natural reaction of Control panel & Keypad wired

inputs is DEL

Keyfob natural reactions:

(or )= SET (arm) ,

(or

)= UNSET (disarm) and both simultaneously = Panic. If a

reaction from 2 to 8 is selected (see opposite), only the key

(or ) and double buttons + ( +

) will have it.

The

( ) button has no effect (can still be used for

controlling UC/AC receivers).

• Assignment to sections will only have an effect on partial

arming or if the system is split (except PG output control)

• For partial arming, a pair of keyfob buttons assigned to

section:

A has the effect:

(or )=SET A, (or )=SET AB

B has the effect:

(or )=SET A, (or )=SET AB

C has the effect:

(or )=SET ABC, (or )=UNSET

ABC

• In a split system, a keyfob button pair assigned to section:

A=SET/UNSET A, B =SET/UNSET B, C =SET/UNSET ABC

61 nn r s

Code (card) reactions and section assignment

• A code (card) may have the same kind of reaction as

devices

62 nn r s

nn = address 01 to 50

r = reaction

0 disabled (incl. tamper sensor)

1 Natural – this means:

for detectors=selected by

DIP switch in the detector,

for wired inputs=DELay,

for Codes

(cards)=SET/UNSET

2 Panic

3 Fire

4 24 hours

5 Next DELay

6 INStant

7 SET (arm)

8 PG control (s: 1=PGX,

2=PGY,3=PGX+PGY)

9 SET/UNSET (toggle)

s = section 1=A, 2=B, 3=C - has

to be entered even if the system

is not split and setting

(arming)has no meaning.

In a split system, a code (card)

assigned to C will SET/UNSET

all ABC sections

all Natural

in C

Enrollment by keying in production codes

60 nn xxxxxxxx

nn = address 01 to 50, xxxxxxxx = last 8 digits of the

production code (below the bar code on the device)

Automatic Daily Setting/Unsetting schedule

(arming/disarming)

64nahhmm

n – action sequence index (0 to

a – action:

0=no action

1=SET ABC

2=UNSET ABC

3=SET A

4=SET B (if unsplit then AB)

5=UNSET A (if unsplit then ABC)

6=UNSET B (if unsplit then ABC)

hh - hours, mm - minutes

No action

The scheduled

actions will happen

every day

Changing the service code 5 NC NC

NC = new code (4 digits) 8080 enter NC twice

Go to maintenance mode 292

switches to maintenance

mode

Setting the internal clock 4 hh mm DD MM YY

00:00 1.1.00

Editing keypad text

Text for device names, code names and PG output names are

stored in each individual keypad.

Press and hold the

? key to enter text editing

(the first character of the first address name

will start flashing). Then use keys:

and to select some text (or an address)

1 & 7 character selection (A,B,C,D...8,9,0)

4 & 5 cursor (to the left & right)

2 to erase a character

# = exit editing and save changes

Device

Only capital letters

can be entered this

way. If there are

multiple keypads,

each must be edited

individually this way

or all of them can be

easily programmed

via Comlink software

12.2. Exit delay time

An exit delay time occurs while setting (arming) the system.

During this time period delayed or next-delayed detectors can be

triggered without an alarm occurring. To program the delay time,

enter:

20x

where x is a number from 1 to 9 determining the

duration in steps of tens of seconds (1=10 s,

2=20 s,....)

If there is a final-door detector in the system then the

exit delay is multiplied by 30 s instead(1=30 s,

2=60 s,...)

Example: To program a 20 seconds exit delay, use the

sequence 202 (if there is a final door detector, a 60 seconds

delay will result) .

Factory default setting: x = 3

12.3. Entrance delay time

The entrance delay time is provided to unset (disarm) the

system after a first delayed detector has been triggered. To

program this time, enter:

21x

where x is an number from 1 to 9 determining the

delay in multiples of 5 seconds ( 1=5 s,

2=10 s,....)

If the entrance delay is triggered by a final-

door detector, then parameter x is multiplied

by 30 s instead. (1=30 s, 2=60 s,...) – in this

case it means that the entrance delay would

be six times longer than if it had been

triggered by an ordinary detector.

Example: To program a 20 seconds entrance delay, enter the

sequence 214 ( if the delay has been activated by a final-door

detector, a 120 seconds delay will result instead).

Factory default setting: x = 4

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Jablotron JA-80K Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Jablotron JA-80K

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info