554835
7
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
Installation manual: Oasis security system JA-80K - 7 - MKE51801
control panel twice but to two different addresses with different
features –see 12.40.
Only a single device can be enrolled to each address.
When indicator A lights, it means the displayed address is
occupied and therefore no more devices can be enrolled to
this address.
If a device has already been enrolled to an address, and it is
then re-enrolled to another address, the device’s address
assignment will change from the original address to the new
one.
If a device cannot be enrolled to the control panel, either it
does not have a good wireless connection to the control panel
possibly due to excessive distance or it could be too close to
the control panel (closer than 2 meters is not permitted),
To re-enroll a device, first disconnect its battery. Then wait
about 10 seconds or, to save time, press and release its
tamper switch to quickly discharge any remaining energy.
A sub-control panel can be enrolled to a master control
panel by keying in the sequence 299 on the keypad of the sub
control panel which must be in Service mode. (see 12.10),
If you intend to use final-door detectors in the system, they
must be enrolled to addresses 01 to 05 or 46 to 50 (see
12.23).
11.3. Testing enrolled devices
1. The control panel must have its antenna connected and be
in Service mode. If not in Service mode, then key in 0
service code (factory-default 8080). To enter Service mode
the control panel must be initially unset (disarmed).
2. Trigger the device to be tested (if it is a detector close its
cover first and then wait until it is ready for testing).
3. The keypad will beep and display a description of the signal
received from the device under test (the keypad cover
should be flipped open). We recommend technicians to
carry the wireless keypad around while testing to ease the
process.
Notes:
Motion detectors JA-80P and JA-85P can be tested for a
maximum of 15 minutes after closing their covers. After this
period the detector will ignore frequent movements (see
detector manuals for details).
Devices can also be tested in maintenance mode – see 13.4.
11.4. Measuring signal strength
1. The control panel must have its antenna connected and be
in Service Mode. If it is not, then enter 0 service code
(factory default: 8080). The control panel must be unset
(disarmed) to enter Service Mode.
2. Key in 298, and the lowest enrolled address will be
displayed.
3. Trigger the device enrolled to the displayed address. The
keypad display will show the received signal strength on a
scale of 1/4 to 4/4. Keep the keypad cover flipped open
while measuring signals.
4. Other addresses for devices can be selected using the
arrow keys to measure their signals too.
5. Exit signal measuring by pressing the # key.
Notes:
Motion detectors JA-80P and JA-85P can be tested for a
maximum of 15 minutes after closing their covers. After this
period the detector will ignore frequent movements (see
detector manuals for details).
Measuring the signals from a JA-80L internal siren can be
activated by pressing its button. A JA-80A outdoor siren can
be activated for signal strength measurement by opening its
cover thereby triggering its cover tamper switch.
Each installed device should have a minimum signal strength
of 2/4. If the signal is too weak, the device should be relocated
or a higher control panel sensitivity can be selected. (see
12.36) Alternatively the control panel can be equipped with an
external antenna (see 10).
This measurement shows the quality of the signal received
from the device at the control panel.
The wireless keypad can be carried during installation or
testing by disabling its tamper contact via the jumper near the
tamper contact – do not forget to re-enable the tamper before
finishing the installation – Note: the keypad usually has a
slightly shorter working range than the detectors. Therefore, if
carried to more-distant detectors the triggering of the
detectors might not be shown.
The most convenient way of measurement is via a computer
running ComLink SW.
11.5. Erasing enrolled devices
1. The control panel must be in Service Mode. If it is not, then
enter 0 service code (factory default: 8080). The control
panel must be unset (disarmed) to enter Service Mode.
2. Key in “1” to enter enrollment mode and using the arrow
keys select the desired address of the device you wish to
erase.
3. Press and hold the “2” key until a beep is heard and the A
indicator turns off.
4. After all the desired devices have been erased, press #.
Notes:
To erase all wireless devices, press and hold the “4” key in
enrollment mode.
If a wireless keypad is erased, it will stop communicating with
the control panel and must be re-enrolled before being used
again. (see 7.1).
11.6. Enrolling the control panel to UC and AC
modules
If you wish to use UC and AC modules to output PGX and PGY
signals, you must enroll the control panel to these modules as
follows:
1. The control panel must be in Service Mode. If it is not, then
enter 0 service code (factory default: 8080).
2. On the UC or AC module, enter the desired enrollment
mode (see the manual of the particular module)
3. Key in 299 on the control panel keypad and check that all
LEDs on the module flash a few times to confirm successful
enrollment.
Notes:
Because the UC and AC modules have rather short
enrollment-period timeouts, we recommend locating the
module close to the control panel during enrollment.
Alternatively you could carry the wireless keypad close to the
module to perform enrollment.
The control panel can be enrolled to the desired number of
UC/AC modules to control multiple PG outputs in an
installation.
Each UC and AC module has 2 relays, X and Y which have to
go through enrollment separately. The X relay reacts to PGX
signals from an enrolled control panel and the Y relay reacts
to PGY signals from an enrolled control panel. The control
panel’s PGX signal can be enrolled to the X relay and the
control panel’s PGY signal can be enrolled to the Y relay.
Therefore, the enrollment procedure has to be done twice if
both relays are to be controlled by the control panel’s PG
signals.
Only one control panel can be enrolled to a UC or AC receiver
because a control panel repeats its PG signals every 9
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-80K bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-80K in de taal/talen: Engels als bijlage per email.

De handleiding is 0,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Jablotron JA-80K

Jablotron JA-80K Gebruiksaanwijzing - English - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info