Handleiding Jablotron JA-60GSM (pagina 11 van 11) (Engels)

554884

Verklein

Vergroot

Pagina terug

1/11

Pagina verder

JA-60GSM dialer module 1 / 11 MFJ51215

JA-60GSM dialer module

Installation manual

The JA-60GSM dialer is constructed for the JA-60, 63 and 65 alarm control panels. The dialer is used for communication via GSM. An

appropriate GSM provider is chosen according to the inserted SIM card. This Installation manual is intended for the JA-60GSM, version FJ61412.

The GSM module, when installed in the alarm control panel, enables:

 Automatic sending of an event’s text messages to up to 8 mobile phones

 Dialing of programmed telephone numbers and playing of an audible warning signal

 Data transfer to one or two Central Monitoring Stations (CMS)

 Remote control and programming of the alarm system via SMS instruction messages from a mobile phone or from Jablotron’s SMS

website

 Remote control and programming of the alarm system using a telephone set keypad (mobile or land line)

 Remote control of an appliance (heating system etc.) via telephone (mobile or land line)

 Phone calls and convenient receiving and sending of SMS messages using an SMS-8010 telephone set (optional accessories; except

GSM kits e.g. JK-05) attached to the dialer module (via the GSM network)

 Connection of the intercom SP-01 for communication with the premises

 Internet connection using the GPRS data transfer

 Programming of the alarm system via ComLink software

 Programming and remote supervision of the alarm system via Jablotron’s website www.gsmlink.cz

 Multi-language support (only available via keypad instructions)

1 Installation of the dialer

The JA-60GSM dialer can be installed into the telephone

communicator’s position in a JA-60, 63 or 65 control panel (either a

GSM module or a telephone line communicator module can be used in

a control panel – it is not possible to install both simultaneously).

a) Disconnect the control panel’s power supply (both AC and

backup battery). If the control panel has been previously used

before this installation, enter the programming mode before

disconnecting the power supply.

b) We recommend you to disable the SIM card PIN code

protection before you insert it into the dialer. Use a mobile phone

to perform this task (if you have a NOKIA phone, select: Menu,

Settings, Security settings, PIN code request, Off). If you insist on

usage of the PIN, see section 5.1.

c) Open the SIM card holder (by sliding it in the direction shown in

figure 1) and Insert the SIM card into the holder and close it by

sliding it back. – see figure 1.

d) Attach the dialer into the control panel case and connect its flat

cable to the control panel’s main board.

e) Connect the GSM antenna (never switch the power supply on

without a proper antenna)

f) Connect a SMS-8010 telephone set to the PHONE connector (or to

PHONE terminals) if desired. Only one telephone set can be attached

to the dialer. The PHONE output of the dialer should never be

connected to any other telephone network.

g) If you use the AUX output to control an appliance, connect its

cable to the AUX output terminals (normally open dry contact,

max. 100mA / 60V) – see figure 1.

SPAC E

CANCEL MENU NAMES CALLS WRITE READ



SMS

CALL

MUTE

FLASH

REDIAL

SPEA KE R

figure 1

Note: if your control panel supports programming of the PgX and

PgY outputs for the AUX function (sequences 238 and 239), the

appliance can also be controlled wirelessly from the control panel

by incorporating a UC-216 or UC-222 receiver module into the

system.

h) Reconnect the control panel’s power supply (backup battery

and AC). The system will show a P, (programming mode). The red

LED on the GSM dialer will light permanently (indicating that the

module is establishing a connection with the GSM network). The

LED will switch off after the connection is successfully

established.

If the LED starts flashing, the module was not able to connect to

the GSM network. In this case, switch off the control panel’s power

completely. Remove the SIM card and insert it into a mobile phone

to confirm whether it is possible to connect to the network at this

location. You can also select a desired network manually if options

are available. Ensure that the SIM card does not request a PIN

code (optional use with a PIN code is described in section 5.1).

Once the SIM card works in the mobile phone, reinsert it into the

GSM dialer and repeat step h). If the GSM signal is weak in this

area, change the location of the GSM antenna before you try to

reestablish the connection.

i) Attach the control panel’s cover after the module has connected to

the GSM network (LED switched off).

j) Key in 97701 - to set texts of the communicator to English

language. (English is the default setting, so you can omit this step.)

k) Enter 971 on the alarm system keypad (while in programming

mode) to monitor the GSM signal. The keypad will show a

number from 0 to 9 and it will sound a beep every second

indicating a new measurement. For proper functioning of the dialer

the signal strength should be 3 or higher. Find the best location for

the antenna while measuring the signal strength. To switch the

system back to programming mode press the N key.

l) Without additional programming you can test the user features of

the dialer (phone calls from an attached phone, remote control of

the system via a remote phone, remote control of an appliance

etc.). See the following description.

m) Set telephone numbers for automatic event reporting and the

other selectable features – see part 3.

n) Programming of the GSM dialer is possible by entering

programming sequences via the alarm system’s keypad (while in

programming mode). The most convenient programming method,

however is via a connected PC using ComLink software, or by

using the www.GSMlink.cz

website.

JA-60GSM dialer module 2 / 11 MFJ51215

2 User features of the GSM dialer

The installed GSM dialer offers many useful features described in detail

below, or briefly in table 11. A synopsis is available on the user card.

The installer should properly demonstrate the use of the system to the

user after installation.

2.1 Phone calls from the attached telephone set

After the GSM module is connected to the GSM network, an attached

SMS phone can be used to make calls. If you pick up the phone, you will

hear a dial tone. Simply dial the number you want to call (as if you are

dialing from a normal fixed line phone). You can also dial the GSM

communicator’s phone number from another phone, and its attached phone

will ring as a normal land line phone would. If it is necessary to

communicate with CMS the call from the attached phone will be terminated

in 10 minutes.

If there is a busy tone on the attached telephone set, either the line you

are calling is busy, or the GSM communicator is busy with previous

communication at that moment (for example data transfer to the monitoring

station).

You can also use the attached phone keypad to operate the alarm

system. By pressing the # key, you can toggle the keypad from telephone

mode to alarm system control mode.

Note: some telephone sets are sensitive to the GSM radio signal. For

this reason you may hear a characteristic noise in the telephone

receiver when calling. If the noise is disturbing, change the location of

the phone set (try to keep it as far as possible from the GSM dialer

antenna). Usually it is possible to find a suitable location for the phone

with a minimal level of interference.

2.2 Remote control of the alarm system by telephone

A system equipped with a GSM dialer can be remotely controlled. From a

mobile phone there are two possibilities – either by text instructions sent by

SMS or by dialing-in and operating the system via the phone keypad which

will operate in the same way as the alarm system keypad. The dialing-in

method can also be done from an ordinary landline telephone set.

The following description matches the factory default settings of the

communicator. The described features can be greatly modified in the

programming mode – see part 4.

2.3 General rules for remote control by SMS instructions

 SMS instructions can be sent from a mobile phone or from an SMS

website.

 In SMS, letters are not case-sensitive. Only the basic English alphabet

is accepted by the communicator.

 All SMS instruction words must be separated by a space.

 If the % is used all previous text will be ignored. The %% symbol when

used in SMS text ends processing – all the following text will be

ignored. It is recommended to use this symbol at the end of the

instruction if the provider sends some additional text after your

message (advertisements etc.).

 Warning: if any incoming SMS includes except a valid system

command any extra text which is not separated by % or %%

symbols the command will not be executed

Examples of SMS:

“Hi, this text will be ignored even if I write ME % MO %% Thank

you” – Only MO command will be executed

“Hi, MO” – Command in the SMS will be ignored because there is

an extra text

 The default command texts can be customized by an installer (see

4.2.2). For example the instruction AUXON can be changed to

SWITCH ON HEATING etc.

2.4 Arming by SMS (AM xxxx)

The command AM followed with a valid access code can be used to

arm the alarm system. If the system is already armed, the command will

have no effect. SMS text to be sent to the dialer: AMxxxx

xxxx is a valid alarm system access code (Master or user).

 separating character, which can be replaced by a space

Example: Sending AM 1234 will arm the system, which is equivalent to

using code 1234 for arming by keypad

Notes:

 According to the default setting, the system confirms command

execution with a corresponding SMS reply

 If it is impossible to arm the system – for example if it is in programming

mode, you will be notified about the situation by an SMS reply

 If the alarm system is split, the instruction will effect the section which

belongs to the access code used

 If arming without a code is enabled on the control panel, the AM

command can be used without any access code. In this case the

command performs the same action as the keys F 1 pushed on a

keypad.

2.5 Disarming by SMS (DM xxxx)

Command DM followed with a valid access code will disarm the system.

If the system is already disarmed, the command will have no effect. SMS

text to be sent to the communicator: DM xxxx

xxxx is a valid alarm system access code (Master or user).

 separating character, which can be replaced by a space

Example: Sending DM



1234 will disarm the system, which is

equivalent to entering code 1234 on a system keypad.

Notes:

 The system confirms disarming with a corresponding SMS reply

 If it is impossible to disarm the system – for example it is in programming

mode, you will be notified about the situation by an SMS reply

 If the alarm system is split, the instruction will effect the section which

belongs to the access code used

* If the alarm system is split and a command is used (AM or DM), the user

code will effect the system the same way as if the code had been entered

from the alarm system keypad – no matter if AM or DM is used (will arm if

the system is disarmed and will disarm if the system is armed).

2.6 Mode request by SMS (MO)

Command MO can be used to read the current alarm system mode.

The dialer will reply with a reporting SMS to the phone which sent the

MO command about status, level of GSM signal, GPRS status, success

of transferring data to the CMSs. SMS text to be sent to the dialer: MO

Example: If the system is armed, it will reply to the MO instruction with

the SMS: Alarm system reports: Control panel status:

Armed,GSM:7,GPRS OK,MS1 NOT,MS2 OK

Note: if you want to protect this command with a password, set your

own instruction text including the password – see section 4.2.2

2.7 Last event request by SMS (ME)

Instruction ME can be used to read the last event recorded in the alarm

system’s memory. The dialer will reply with a reporting SMS. SMS text

to be sent to the dialer: ME

Example: After a fire alarm, it will reply to the ME instruction with the

SMS: Alarm system reports: Last event: Alarm end Control panel Time:

02.06. 19:48

Note: if you want to protect this command with a password, set your

own instruction text including the password – see section 4.2.2.

2.8 Appliance remote control by SMS (AUXON, AUXOFF)

These commands can be used to operate the AUX output (for example

the heating in a house). The dialer confirms command execution with

an SMS reply.

To switch on the AUX output, send SMS text: AUXON

To switch off the AUX output, send SMS text: AUXOFF

Example: to switch on heating send SMS: AUXON

Note: texts of these instructions can be customized and protected with

a password – see section 4.2.2. Outputs PgX and PgY can be

controlled by SMS commands PGON and PGOFF.

2.9 Remote programming of the alarm by SMS (yyyyy PRG seq)

Command PRG can be used to send programming and operating

sequences to the alarm system. It has the same effect, as if the sequences

had been entered on the alarm system keypad. Type the instruction as:

yyyyy PRG seq,seq,seq,

where

yyyyy is the remote access code; factory default setting is 0000 (4

zeros); the code can be changed, see section 5.4

PRG is the command identification

seq are the programming or operating sequences, consisting of

characters 0 to 9, F, N. There can be more than one sequence in

one SMS. The particular sequences should be separated with a

comma or dot. The number of sequences in one SMS is limited

by the maximum size of the SMS in the GSM network.

 separating character, which can be replaced by a space

Example: if the control panel is disarmed and its Installer code is 6060, then

the duration of the alarm can be programmed to 5 minutes and the acoustic

indication of the exit delay can be disabled by sending the following SMS:

0000 PRG F06060,225,330,N

After receiving the SMS command, the control panel will first enter

programming mode (F06060) then sequences 225 and 330 will be

executed and at the end programming mode will be exited (N).

JA-60GSM dialer module 3 / 11 MFJ51215

2.10 Alarm system remote control from a telephone keypad

If you want to operate the alarm system from a phone (mobile or

landline), perform the following:

a) Dial the alarm system phone number. The attached telephone

will ring

b) If the phone is not answered, the system will answer after 25

seconds - indicated by a short beep

c) Enter the remote access code; factory default is 0000 (4 zeros);

to change this code see section 5.4

d) Confirmation sounds indicate the control panel mode: 1 beep =

armed, 2 beeps = disarmed, 3 beeps = programming mode,

Siren sound = alarm.

e) From this moment the telephone keypad will work as the alarm

control panel keypad. The

* Key is interpreted as F, the # key

as N.

f) Confirmation sounds indicate the control panel mode: 1 beep =

armed, 2 beeps = disarmed, 3 beeps = programming mode,

Siren sound = alarm.

g) To terminate the connection simply hang up. The connection will

also be terminated if there is no entry within 60 seconds.

Notes:

 Remote access from a landline is only possible from a phone

using tone dialing (DTMF)

 The reaction of the alarm system to incoming calls can be

modified: see section 5.3

 It is impossible to operate the system remotely without a valid

remote access code (if used).

2.11 Appliance remote control via a telephone keypad

If you want to operate outputs PgX or PgY (e.g. a household

appliance) from a phone (mobile or landline), perform the following:

a) Dial the alarm system number. The attached telephone will ring.

b) If the phone is not answered, the system will answer after 25

seconds - indicated with a short beep.

c) Enter the remote user access code; factory default setting is 1111 ;

to change this code see 5.4.

d) The system will confirm validity of the code with a beep.

e) From this moment you can operate the PgX and PgY outputs (if

they are each predefined as phone-controllable) by entering:

*80 to switch off PgX or PgY, or both together,

*81 to switch on PgX or PgY, or both together

(continuously).

f) To terminate the connection simply hang up. The connection will

also be terminated if there is no entry within 60 seconds.

Notes:

 Remote access from a land line is only possible from a phone

using tone dialing (DTMF)

 The reaction of the system to incoming calls can be modified: see

section 5.3

 If the system is not allowed to control without code, the control

sequence must be complete with a user code:

*8[user code]1

*8[user code]0

 For this function it is necessary that the alarm system supports F

81 and F 80 sequences

 If the dial in function is set (see 3.1.) it is possible to switch ON

the PgX or PgY output for two seconds. The phone call is not

answered therefore it is free of charge.

2.12 Remote voice communication with premises

If the SP-01 intercom is plug-in to the PHONE terminal (it must not be

combined with any phone connected) it is possible to create a one way

(talking or listening) communication from an authorized (stored) phone

numbers (see. 3.1). Procedure:

a) From an authorized phone dial the JA-60GSM phone number.

The SP-01 will ring once and then it will answer the call

b) Potential alarm on the control panel will be terminated

c) You can talk to the premises

d) For switching to the listening mode press 5 on your phone.

For switching back to the talking mode press key 2. Or by

pressing button 1 it is possible to toggle between talking and

listening.

e) Press 0 or hang-up to terminate the call.

Note:

 Only a phone with available DTMF can be used.

3 SMS and audible alarm reports

The factory default settings allow the GSM dialer to send SMS

reports and audible warnings when the control panel generates

important information (alarms, arming, etc.). It is only necessary to set

the telephone numbers which the information should be reported to. To

enter these numbers, first enter programming mode.

If you prefer to report more or different events than the factory

default provides, see section 4.

3.1 Telephone numbers entering

The dialer has 8 telephone number memories. Each memory has

assigned particular SMS reports and/or audible warnings according to the

default setting – see table 1.1. By entering a telephone number in to a

particular memory location you are selecting what will be reported to this

number:

7t xxx...x F0

Where t is a memory location from 1 to 8

xxx...x is a telephone number (max. 20 digits),

enter F9 before the number, if you need the + prefix for international

calls. To use an attached SMS telephone set, enter code 001 instead of

the telephone number. To authorize a phone number for communication

with premises via the SP-01 intercom set F8 (#) at the end of the phone

number or F7 (*) for dial-in function (see 2.11.).

To disable reporting to a particular number, delete this number

memory by entering:

7tF0

where t is a memory from 1 to 8

Report testing:

If you wish to report any alarm, arming and disarming by SMS followed

by the notifying call and your mobile phone number is 123456789, then

enter 75123456789F0 (while the control panel is in programming mode).

Then exit programming mode by pushing the N key. Now you can arm

the system and your mobile phone will receive a reporting SMS.

3.2 Installation name in SMS reports

Each reporting SMS message starts with: “Alarm system reports:”. You

can change this default title text by sending the dialer the following text

programming SMS:

yyyyyTXT700,text

where

yyyyy is the remote access code; factory default is 0000 (4

zeros); the code can be changed, see 5.4

TXT is the text programming command

700 is the index number on the system text table

corresponding to the installation name

, comma (separator)

text is your own new installation name. A comma or dot

cannot be used in the text. A blank space inside the

text is a valid character (the dialer ignores spaces

before the separator)

 separating character, which can be replaced by a space

Example: If the default code is in the dialer, then sending SMS:

0000 TXT 700, Mr. Diamond’s jewelry shop reports:

to the dialer will change the installation name to the above text.

Note: all the SMS texts stored in the dialer can be changed in a similar

way, see section 4.2 for details.

JA-60GSM dialer module 4 / 11 MFJ51215

3.3 Telephone number table

4 Customization of SMSs and audible reports

The default text and audible reports sent can be modified.

 The dialer can report all possible events of the alarm system by SMS

(see table 4.1.1).

 It is possible to set which events will be reported to which telephone

number.

 There are factory default SMS texts available for all possible events and

for all possible event sources. All these texts can be edited.

 It is possible to set which events should activate audible warnings.

 The communicator can report all possible events by dialing programmed

numbers and playing an audible warning - if the call is answered

 It is possible to change SMS command texts, which are used for remote

control of the system.

First enter the programming mode if you are going to use the following

programming sequences:

4.1 Events to be reported by SMS

Table 4.1.1 shows the complete list of all possible events in the alarm

system together with each corresponding index number. It also shows

which events are assigned to which telephone numbers to be reported

by SMS. You can make your own setting by using:

81 uu t y

where

uu is the event index from 01 to 31 (see table 4.1.1)

t is a telephone number memory location from 1 to 8

y 0 = reporting disabled, 1 = reporting enabled

Note: SMS reports consist of 4 text parts (installation name, event

name, event source name and time) – all of these texts can be edited

and customized, see section 4.2 for details. In a single SMS there can

be up to 160 characters using ASCI format, or 65 characters using

UNICODE format. Exceeding these limits will result in split messages.

The event “Internal communication failure” is generated if any of the

wireless detectors are lost under RF supervision.

The event “External communication failure” is generated if there is a

GSM signal outage longer than 15 minutes. The release of this event

is possible when GSM signal monitoring is set to ON.

Example: if you enter 810381 and a Fire alarm is triggered (event

index 03) by detector number 1, the following message will be sent to

the 8

telephone number: “Alarm system reports: Fire alarm Wireless

detector #1 Time: 16.04. 11:16”

4.1.1 Table – SMS report assignments to telephone numbers

Telephone numbers Event index

Event

1 2 3 4 5 6 7 8

01 Intruder alarm – instant zone x x x x x x

02 Intruder alarm – delayed zone x x x x x x

03 Fire alarm x x x x x x

04 Panic alarm x x x x x x

05 Wrong access code alarm x x x x x x

06 Alarm after power on x x x x x x

07 Tamper alarm x x x x x x

08 Tamper OK

09 Alarm end

10 Alarm canceled by a user x x x x x x

11 Arming

x x

12 Disarming

x x

13 Partial arming (Home) x x

14 No code arming x x

15 External communication failure x x x x x x x

16 External communication recovery

17 Failure x x x x x x x

18 Failure recovery

19 AC failure longer than 30 minutes x x x x x x x

20 AC failure

21 AC recovery

22 Battery failure x x x x x x x

23 Battery recovery

24 Enter programming mode

25 Exit programming mode

26 Remote access

27 Remote access – end

28 RF jamming

29 Internal communication failure x x x x x x x

30 Internal communication recovery x x x x x x x

31 Periodic test

The x marks in the table show which events are assigned to which telephone numbers for SMS reporting. If you modify these, we recommend you to

mark your settings in the table.

Memory

Entry

sequence

Reporting mode for the two corresponding phone numbers: Notes

1 71 ______ F0

2 72 ______ F0

- ALARM SMS if there is any type of alarm in the system (intruder, fire, tamper, panic).

- Technical SMS about events in the system.

3 73 ______ F0

4 74 ______ F0

- ALARM SMS if there is any type of alarm

- ALARM CALL notifies the called person (if you answer such a call, you will hear an

audible warning).

- Technical SMS about events in the system.

5 75 ______ F0

6 76 ______ F0

- ALARM, ARMING & DISARMING SMS.

- ALARM CALL notifies the called person (if you answer such a call, you will hear an

audible warning).

- Technical SMS about events in the system.

7 77 ______ F0

8 78 ______ F0

- ALARM CALL notifies the called person (if you answer such a call, you will hear an

audible warning). This setting is suitable for notifying landline numbers. -

Technical SMS about events in the system. This position is reserved only for the

service/installer organization.

 Only numbers, which can accept

SMS, should be entered for the SMS

reports (mobile phones, provider’s

call centers etc.)

 Audible warnings can be sent both to

mobiles and to landlines too

 The communicator can report all

possible events from the alarm

system, not only the events listed in

the table above. See section 4 for

details.

JA-60GSM dialer module 5 / 11 MFJ51215

4.2 SMS text editing

The list of SMS texts stored in the dialer consists of texts reported as

event reports (installation name, event name and source name) and

texts for remote control instructions. All these texts can be changed by

the following SMS form:

yyyyyTXTy,text, y,text,…..

where

yyyyy is the remote access code; default setting is 0000 (4

zeros); the code can be changed, see 5.4

TXT is the text programming command

y is the text index (from 1 to 711, see table 4.2.1).

, comma (separator)

text is the new customized text string. Neither a comma nor a

period (full stop) can be used inside the text. A space

inside the text is a valid character (the dialer ignores

spaces outside the “text” string)

Note: a single TXT command SMS can change more than one text

(limited by the maximum SMS size of the SMS in of the GSM network).

Example: If the factory default code in the dialer is 0000 (four zeros),

then sending SMS:

0000



TXT



201, uncle Sam’s controller, 202, aunt Mary’s controller

to the dialer will change the names of remote controller numbers 1 and

4.2.1 Table – complete list of SMS texts

Text index y Factory default text Text index y Factory default text

1 Intruder alarm – instant zone 403 Wireless detector #3

2 Intruder alarm – delayed zone 404 Wireless detector #4

3 Fire alarm 405 Wireless detector #5

4 Panic alarm 406 Wireless detector #6

5 Wrong access code alarm 407 Wireless detector #7

6 Alarm after power on 408 Wireless detector #8

7 Tamper alarm 409 Wireless detector #9

8 Tamper OK 410 Wireless detector #10

9 Alarm end 411 Wireless detector #11

10 Alarm canceled by a user 412 Wireless detector #12

11 Arming 413 Wireless detector #13

12 Disarming 414 Wireless detector #14

13 Partial arming (Home) 415 Wireless detector #15

14 No code arming 416 Wireless detector #16

15 External communication failure 501 User code #1

16 External communication recovery 502 User code #2

17 Failure 503 User code #3

18 Failure recovery 504 User code #4

19 AC failure longer than 30 minutes 505 User code #5

20 AC failure 506 User code #6

21 AC recovery 507 User code #7

22 Battery failure 508 User code #8

23 Battery recovery 509 User code #9

24 Enter programming mode 510 User code #10

25 Exit programming mode 511 User code #11

26 Remote access 512 User code #12

27 Remote access – end 513 User code #13

28 RF jamming 514 User code #14

29 Internal communication failure 600 Control panel status:

30 Internal communication recovery 601 Armed

31 Periodic test 602 Disarmed

101 Control panel 603 Exit delay

102 Subsystem 604 Entrance delay

103 Wireless siren 605 Alarm

104 GSM dialer 606 Programming mode

105 Digital line 607 User mode

110 Master code 608 Partially armed

201 Controller #1 609 Battery failure

202 Controller #2 610 Tamper alarm

203 Controller #3 611 Alarm memory

204 Controller #4 612 System failure

205 Controller #5 613 Power supply failure

206 Controller #6 614 Control panel status unknown

207 Controller #7 621 Time:

208 Controller #8 622 Last event:

301 Wired detector #1 623 SMS processing failure.

302 Wired detector #2 624 Credit unknown

303 Wired detector #3 625 Text will be inserted by instruction CREDIT (see 5.14)

304 Wired detector #4 650 SMS processed successfully.

305 Wired detector #5 651 Wrong SMS processing.

306 Wired detector #6 653 AUX switched ON

307 Wired detector #7 654 AUX switched OFF

308 Wired detector #8 700 Alarm system reports:

309 Wired detector #9 703 AM

310 Wired detector #10 704 DM

311 Wired detector #11 705 MO

312 Wired detector #12 706 ME

313 Wired detector #13 707 AUXON

314 Wired detector #14 708 AUXOFF

315 Wired detector #15 709 CREDIT

316 Wired detector #16 710 PGON

401 Wireless detector #1 711 PGOFF

402 Wireless detector #2

JA-60GSM dialer module 6 / 11 MFJ51215

4.2.2 Editing of remote control SMS commands

If you change any of the text strings from 703 to 711, the dialer will

recognize the new text string as the valid remote control command.

E.g., if you change text “MO” (number 705) to “Tell me my alarm

status please” it will be possible to read the control panel status by

sending the new string as the SMS command. This function helps

customers keep the commands secret and protect the dialer against

unauthorized operation.

4.3 Assignment of audible warnings to be reported

Table 4.3.1 shows the complete list of all possible events in the alarm

system. It also shows which events are assigned to which telephone

numbers to be reported audibly. You can make your own setting by:

82 uu t y

where

uu is an event index from 01 to 31

t is a telephone number memory location from 1 to 8

y 0 = reporting disabled, 1 = reporting enabled

4.3.1 Table – audible warning assignments to telephone numbers

The x marks in the table show which events are assigned to which telephone numbers to be reported audibly. If you modify these, we recommend you

mark your setting in the table. If there is an alarm, a siren sound will be played, for other events a melody sound will be played.

Telephone numbers

Event index uu Event

1 2 3 4 5 6 7 8

01 Intruder alarm – instant zone x x x x x

02 Intruder alarm – delayed zone x x x x x

03 Fire alarm x x x x x

04 Panic alarm x x x x x

05 Wrong access code alarm x x x x x

06 Alarm after power on x x x x x

07 Tamper alarm x x x x x

08 Tamper OK

09 Alarm end

10 Alarm canceled by a user

11 Arming

12 Disarming

13 Partial arming (Home)

14 No code arming

15 External communication failure

16 External communication recovery

17 Failure

18 Failure recovery

19 AC failure longer than 30 minutes

20 AC failure

21 AC recovery

22 Battery failure

23 Battery recovery

24 Enter programming mode

25 Exit programming mode

26 Remote access

27 Remote access – end

28 RF jamming

29 Internal communication failure

30 Internal communication recovery

31 Periodic test

Example: if you enter 820381 and a Fire alarm is triggered (event index 03) the dialer will call the 8

telephone number and it will play audible warning if

the call is answered.

4.4 Temporarily disabling SMS and audible reports

If you need to disable all SMS and audible reports temporarily to all

telephone numbers, use the following sequence:

800 all reports disabled the communicator will send

neither the alarm SMS nor acoustic warnings

801 all reports enabled the communicator will send the

audible reports and SMS messages according to the settings

in chapter 4.1.1. and 4.3.1.

802 the communicator will send the preset reports except the

events of "arming" and "disarming" by Master code, user codes 1 to

4 and controllers 1 to 4

Default setting: all reports enabled (801).

5 General settings

Enter programming mode if you are going to use any of the following

sequences.

5.1 Using a SIM card with a PIN code

It is recommended to use a SIM card with the PIN code protection

disabled (this can be done with a mobile phone, see section 1). If you

insist on using a PIN code, enter it after the GSM dialer has been

powered up using:

70 xxxx F0

where:

xxxx is the PIN code (4 digits)

Example: if the PIN code is 1234 enter 701234F0

Default setting: 70F0 the PIN code protection is off

Note:

 If the dialer does not connect to the GSM network after

powering up (LED starts flashing), there is a probability that a

wrong PIN code was set. In this situation:

o enter 70F0 on the control panel keypad when in programming

mode (PIN code erasing in the dialer)

o disconnect the control panel’s power supply (AC and battery)

o remove the SIM card, insert it into a mobile phone and check

the PIN code. Check also that it is possible to connect to the

desired GSM network at the location of the dialer’s GSM

antenna.

o if you are sure the PIN code is right and the location is covered

by a GSM signal, insert the SIM card back in to the dialer, switch

the power supply on, enter the PIN code (70 PIN F0) and wait

until the communicator connects to the GSM network (LED will

turn off).

JA-60GSM dialer module 7 / 11 MFJ51215

 If you are going to change the current SIM card in the dialer for

another one and the former one used a PIN code, enter

programming mode first and enter 70F0 (PIN code erasing in

the dialer).

5.2 GSM signal checking

If this function is enabled, the dialer will check regularly whether the

GSM signal is available. If it is not available for more than 15 minutes,

the system will indicate an external communication failure (failure L).

910 checking disabled

911 checking enabled

Default setting: checking disabled (910)

5.3 Reaction to an incoming call (remote access)

This sequence sets how the dialer will react to incoming calls. This

setting is important for remote access by telephone.

93 x

where

x = 0 no reaction to an incoming call

x = 1 to 8 will answer after 1=5sec., 2=10sec.,…,

8=40 seconds

x = 9 will answer after the second call = after the

ring is detected, there must be a pause

of 10 - 45 seconds. The dialer will answer

on the very first ring of the second call.

This setting can be used to bypass an

answering machine connected to the

phone output.

Default setting: 935 – the communicator will answer after 25 seconds

5.4 Remote access code setting

The following sequences are used for programming:

5.4.1 Service remote access code

94 xxxxxxxx F0

where

xxxxxxxx is the code, it can have 1 to 8 digits

If you enter 94F0 - the code will be erased and the remote access to

the alarm system will be not allowed.

Default setting: 0000 (4 zeros)

5.4.2 User remote access code

94 xxxxxxxx F1

where

xxxxxxxx is the code, it can have 1 to 8 digits

If you enter 94F1 - the code will be erased and user remote access to

the alarm system will be not allowed.

Default setting: 1111

5.5 Confirmation SMS reply messages

After the valid processing of an incoming SMS command, the dialer

automatically replies to the sender with a confirmation SMS message.

This confirmation is selectable:

950 automatic reply is disabled

951 automatic reply is enabled

Note: if the automatic reply is disabled, you can request a reply

manually by adding a space and the letter C after the last character of

the SMS instruction.

Default setting: 951 – automatic reply is enabled

5.6 Reset to default settings

Entering 96060 will cause the return to the default settings (all

telephone numbers will be erased and all unsent data will be erased.

For reloading the factory default SMS texts choose the language again

by the sequence 97701 (for English) or 9770x according to section

5.18.

5.7 Total reset – all communications disabled

Entering 96061 will erase all of the settings in the dialer’s memory and

the list of SMSes will be set to default setting.

5.8 One-time dialing-in during programming mode

While the control panel is in the programming mode, you can enable

one-time remote access by entering 970. After this code has been

entered, the dialer will respond to the first ring of any incoming call.

Without requesting the access code, it will enable the calling phone’s

keypad to be used as the keypad of the alarm system (= F, # = N).

This mode will be disabled after you dial-in, or after you exit

programming mode.

5.9 GSM signal monitoring

Enter 971 on the alarm system keypad (in programming mode) to

measure the GSM signal strength. The keypad will show a number

from 0 to 9 and it will sound a beep every second indicating a new

measurement each time. For proper functioning of the module the

signal strength should be 3 or higher. Find the best location for the

antenna while measuring the signal strength. To switch the system

back to programming mode press the N key.

Note: The standard antenna supplied with the JA-60GSM has a gain

of +3dB.

5.10 Attached phone function

The dialer provides a PHONE output to connect an ordinary

telephone set. The function of this telephone can be modified by

entering:

98 y

Where Function

y = 0 An ordinary telephone line is simulated, it is possible to

make phone calls (indicated with a dial tone in the

receiver)

1 If you pick up the receiver, the telephone keypad will work

as the keypad of the alarm system. It is impossible to

make phone calls in this mode (you will hear sounds of

the alarm keypad in the receiver)

y = 2 Disabled - the telephone has no function

y = 3 Emergency call – if you pick-up the phone, it will

automatically dial the emergency number (see 5.11)

Notes:

 If y=0 and you pick up the phone, the telephone keypad can be

switched to the alarm system keypad mode by pressing the #

key.

 If y=3 and you press the



key less than 2 seconds after you pick

up the phone, you will hear the dial tone and you can then call

any number. If the # key is used the same way, the keypad will

switch to the alarm system keypad mode.

Default setting: y = 0 ordinary telephone line is simulated

5.11 Setting the emergency call number

If the attached telephone is programmed for emergency calls (see

section 5.10), it dials the emergency number after you pick up the

receiver. This number can be entered by:

99 xx...x F0

where:

xxx…x is a telephone number (max. 20 digits), enter

F9 before the number if you need + prefix

for international calls

Default setting: no phone number is set (99F0)

5.12 Function of attached SMS-8010 phone

The communicator has a telephone connector, which can be used for

connection to a SMS-8010 phone. A detail description is in the

separate manual enclosed with the SMS-8010 phone. To use an SMS

phone enter code 001 instead of the telephone number (see chapter

3.1)

Setting:

 For sending SMSs to mobile phones it is necessary to set SMS

center 1 to “1111”..

 By sending SMSs to telephone number “001”, the central

panel can be controlled using SMS instructions

Note:

 Displaying the caller’s telephone number (CLIP): The

telephone number is shown in the international format

(00420212345678).

 If the phone call is made from a JA-60GSM a telephone

number of 001 and name of the caller “JA-60GSM“ will be

displayed.

JA-60GSM dialer module 8 / 11 MFJ51215

5.13 Sustain calls for prepaid SIM cards

If a prepaid card is used, the dialer can automatically perform a sustain

call if there were no calls within a 3 month period. It will dial the

programmed number and after a 10 second call duration, the dialer will

hang up. The number, which should be called, can be entered by:

973 xxxxxxxx F0

where: xxxxxxx is the telephone number (max. 20 digits) – it is

recommended to call a time check service, weather reports etc.

5.14 Prepaid SIM cards

The JA-60GSM communicator can send information about the credit

balance of a prepaid SIM card. An SMS sent from any of the stored

numbers (sequence 7t...) containing the word CREDIT followed by the

correct command (different for every provider) will result in sending

information about the credit. Please ask your mobile phone provider for

more information.

CREDIT xxxxx where xxxxx is a string, which depends on the

GSM provider. Ask your provider for more

details

If you want to check the credit regularly use the following sequence.

CREDIT uuu..u xx yyy zz

where: uuu…u is the GSM-provider-defined instruction to be

transmitted to the provider for receiving information about the

amount of credit

xx is the time period (in days) between credit checks.

yyy is the minimum acceptable level of credit. A value

lower than this threshold triggers a warning SMS.

zz is an index or pointer, measured in characters from

the start of the provider message, showing the

position of the first digit of the credit value in the

information SMS sent by the provider. This allows the

GSM dialer to extract the credit value.

If the credit level is lower than the set value (yyy) the event “battery

discharged GSM communicator” will be sent to the preset telephone

numbers. If the credit is restored the event “battery OK GSM

communicator” will be sent to the preset telephone numbers. To

disable this function set the time (xx) period to 00.

Note:

 The user is responsible for the level of the credit

 The producer does not recommend the use of prepaid

cards.

When automatic credit checking is set to disabled, the user will be

unaware of expired credit. . Many GSM providers also demand regular

credit recharging. Therefore a prepaid SIM card is not recommended.

5.15 Telephone volume

The volume and sensitivity of the attached telephone can be adjusted

by:

974x receiver volume

975x microphone sensitivity

where x can be from 1 to 9 (factory default is 5 for both)

If the system is in programming mode, the volume can be adjusted

during a phone call.

5.16 GPRS communication setting

GPRS can be used for communication with a www server, for

connecting a PC to the internet or for communication with a CMS.

GPRS must be activated on the SIM card (for detailed information ask

your GSM provider). It is also necessary to set the APN in

programming mode in the communicator using ComLink software.

5.17 GSM module reset

Enter 976 to disconnect and connect the GSM module to the GSM

network. This function is useful when it is necessary to switch the

mobile device off and on (e.g. when the SIM card has been unblocked

by the mobile operator).

It is also possible to send the command via SMS in the form yyyyy*GSM,

where yyyyy is service access code. The command is processed

independent of the state of the system.

5.18 Language setting

Language of the text used by the communicator can be set by

instruction:

977 xx

where:

xx is number of the language – see the following list:

01 EN English 09 PL Polish

02 CZ Czech 10 PT Portuguese

03 SK Slovak 11 RU Russian

04 DA Danish 12 SE Swedish

05 FI Finnish 13 TR Turkish

06 DE German 14 ES Spanish

07 HU Hungarian 15 NL Dutch

08 IT Italian 16 CN Chinese

Note:

 Set the language before editing the text in the system (change of

the language will change the text to the factory default).

 Set language will not be changed when reset is performed.

 Language setting can NOT be performed via the ComLink

software or the GSMLink.

 This feature is only available for communicators equipped with

SW version FJ61412 or higher.

 Do not use *.jag files for language setting.

Example: by setting 97702 the Czech language will be set.

Factory default : 97701 = English

6 Web server remote access

6.1 System programming

The GSMLink server allows a user/installer to read and change the

control panel and dialer configurations. Data transfer is achieved by

sending an SMS or GRPS data. The web site allows the following

programming:

 control panel settings

 dialer settings

 editing of SMS reports

 monitoring station settings

The web site is also able to read the event memory of the control

panel. The amount of data sent by SMS is optimized to minimize costs.

Alternatively GPRS data transfer can be used, but this must be

activated on the SIM card.

6.2 Web site registration

System registration can be performed in two ways:

The www.gsmlink.cz website

– to register your system use the

registration code printed on the warranty certificate (the code has a

form xxxx-xxxxx-xxxx and it is a unique for each system). The dashes

(-) must be included when registering.

By mobile phone – when the alarm system is in programming mode,

enter 972 xxxx F0 on the alarm system keypad (xxxxx is your mobile

phone number). After a moment you will receive an SMS with the

registration code and the system will register on the web server.

7 Central Monitoring Station communication settings

The dialer can report events to two different Central Monitoring

Stations (CMS). Each CMS has its own setting sequences that differ in

parameter p (p=1 for CMS1 and p=2 for CMS2). The dialer uses

Ademco Contact ID format and it is also equipped for the future use of

GPRS data transfers. The product is able to report events to a CMS

based on either landline or GSM data transfer.

7.1 CMS phone number entry

Primary and back up telephone numbers can be entered for each CMS:

Primary number: 01 p xx....x F0

Back up number:

02 p xx....x F0

where:

xxx...x is a telephone number, max. 20 digits

p 1=CMS1, 2=CMS2

Example: 123456789 can be entered as the CMS2 primary number by

entering: 01 2 123456789 F0

JA-60GSM dialer module 9 / 11 MFJ51215

Note: The IP address can be set a similar way. For example the IP

address 192.168.1.123 on port 08080 can be set by entering 01 2 F8

129 168 001 123 8080, where F8 (#) introduces the IP address, which

must always have 12 numbers, and the port 5 numbers

CMS phone number erasure is possible by entering 01pF0 or 02pF0.

There will be no data transfer to a CMS if its numbers are erased.

Default setting: No phone number set

7.2 Account ID setting

A CMS uses this ID number for alarm system identification:

03 p zzzz F0

where:

zzzz is the account ID number (z = numbers from 0 to 9 or

A=F1, B=F2, C=F3, D=F4, E=F5 a F=F6)

p 1=CMS1, 2=CMS2

Default setting: ID is 0000 for both CMSs

7.3 Format setting

This sequence is used to select the communication format:

04 p x

where:

p 1=CMS1, 2=CMS2

x protocol type – see table

Protocol Type x

Contact ID DTMF 0

Jablotron SMS SMS type

Jablotron GPRS GPRS type

Default setting: Contact ID for both CMSs

7.4 Events to be reported to CMS

There are 31 types of events, which can be reported to each CMS –

see table 7.4.1. This sequence sets which events should be reported

to CMSs.

05 p uu y

where

p 1 = CMS1, 2 = CMS2

uu events index – see table 7.4.1

y 0 = report disabled, 1 = report enabled

Default setting: all reports are disabled

7.4.1 Table – complete list of events to be reported to CSM

Events index uu Events description

01 Intruder alarm – instant zone

02 Intruder alarm – delayed zone

03 Fire alarm

04 Panic alarm

05 Wrong access code alarm

06 Alarm after power on

07 Tamper alarm

08 Tamper OK

09 Alarm end

10 Alarm canceled by a user

11 Arming

12 Disarming

13 Partial arming (Home)

14 No code arming

15 External communication failure

16 External communication recovery

17 Failure

18 Failure recovery

19 AC failure longer than 30 minutes

20 AC failure

21 AC recovery

22 Battery failure

23 Battery recovery

24 Enter programming mode

25 Exit programming mode

26 Remote access

27 Remote access – end

28 RF jamming

29 Internal communication failure

30 Internal communication recovery

31 Periodic test

7.5 CMS re-dialing pause setting

If the dialer is activated it attempts to make a connection (alternating

between the primary and the backup telephone number). If it is not

possible to make a connection, a pause is initiated. After this pause

the dialer will attempt again. The pause length can be set in the

following way:

06 p t

where

t pause duration x 5 minutes (1 = 5 minutes, 2 = 10

min,..., 9 = 45 minutes)

p 1 = CMS1, 2 = CMS2

Default setting: 5 minutes for both CMSs

7.6 Interval of periodic test

The periodic test for checking the CMS link is set by activating event

No 31. The following sequence sets the time length from the last

reported event to the moment when the periodic test report should be

transferred.

07 p hhmm

where

p 1 = CMS1, 2 = CMS2

hh hours

mm minutes

Default setting: The periodic test report is sent 24 hours after the last

reported event.

7.7 Disabling CMS communication

If you need to disable all CMS reports temporarily, you can do this,

while retaining your settings:

0 0 p 0 all reports to CMS p disabled

0 0 p 1 all reports to CMS p enabled

Default setting: all CMS reports disabled.

7.8 CMS 2 as a back up for CMS1

CMS 2 can serve as an optional back-up for CMS if data transfer to

CMS1 fails. When the first event is transferred to the backup

monitoring station (CMS2) an event “tel. line #1 communication fault“

will be reported.

080 CMS1 and CMS2 are two independent stations

081 CMS 2 works as a back up for CMS 1.

When 081 is selected, CMS 2’s settings are used only in the case of

CMS 1 transfer failure.

Default setting: two independent CMSs.

7.9 Storing the event “data to CMS sent” into the event memory

By this sequence it is possible to disable recording of the event that

indicates that data to a CMS has been sent to the list of event in the

control panel.

Programming sequences:

090 The CMS data transfer event is not recorded

091 The CMS data transfer event is recorded

Default setting: The CMS data transfer event is recorded

8 The modem function

The GSM communicator can also be used as an external modem for

accessing the Internet (GPRS format). It is necessary to have GPRS

activated in the SIM card and to have a connection cable connected to the

COM port of the PC. Support for MS Windows operating systems can be

found on the enclosed CD. The modem can only be used when all CMS

reports, SMSs and system calls have been executed.

When the modem is used:

 It is possible to use the attached telephone, the internet connection will

be temporally suspended

 Received SMSs are stored and they will be processed after modem

disconnection

 The modem will be disconnected if an alarm or an arming event occurs

9 Additional information

9.1 Priorities for event reporting:

If the dialer is activated to send an event report it will:

 send information to CMS1 (trying primary and back up

numbers twice) if programmed

JA-60GSM dialer module 10 / 11 MFJ51215

 send information to CMS2 (trying primary and back up

numbers) if programmed

 send SMS reports (1

telephone number, 2

telephone

number,…. 8

tel. number)

 send audible reports (1

telephone number, 2

telephone

number,…. 8

tel. number) – each number is only called

once, whether it is answered or not

 if the attempt to send a report to a CMS has not been

successful, the dialer will try to resend it after the re-dialing

pause (sequence 06px). The dialer will make three attempts

at sending event reports to a CMS, i.e. it will wait (according

to the setting 06px) twice for the re-dial pause. Only a new

event will result in an additional attempt to call the CMS.

If any event is triggered which should be reported to a CMS while the

alarm system is being remotely accessed by phone, the report will be

sent after remote access has finished.

If a user cancels an alarm, all reports, which have not been sent yet,

will be deleted, except for CMS reports.

9.2 The LED on the dialer PCB

 LED flashing means the dialer has not entered the GSM network



LED flashing (3x) – the communicator (modem) is controlled by a PC.

 LED being on means– communication with a GSM network

 connecting to the GSM network

 the dialer is calling

 the dialer is sending an SMS

9.3 Entering programming mode

 The dialer will finish the current CMS connection (the attached

phone will ring shortly to confirm this)

 The current audible warning is interrupted immediately

 SMSs and audible warnings, which remain unsent before entering

programming mode, are erased – they will not be sent after exiting

programming mode

 Unsent event reports to a CMS are erased only in the case of a

telephone number, account ID or communication format change

 Information about the end of fault events is transferred to the

monitoring station during programming mode

 Changes of setting will take affect after exiting programming mode

9.4 The master code holder can change the following

parameters

 Telephone numbers 1 – 7 (see section 3.1)

 SMS and audible warning transfers (see section 4)

 Change of remote user code

 One-time dialing in

 Measuring of GSM signal

 Attached phone functionality

 Telephone number for emergency calls

10 Technical specifications

power 12VDC / max. 1A – provided by the alarm control panel

GSM bands E-GSM/GPRS 900/1800MHz

transmitted power 2 W for GSM900, 1 W for GSM1800

AUX output dry contact, max. 100mA / 60V

comply with EN 50131-1, EN 50136-2-1, 2-3, 2-4

security grade 2 (low to medium risk)

environmental class II indoor-general ( –10 to 40°C)

safety EN 60950

EMC EN 301489-1, EN 301489-7, EN 55022, EN 50130-4

radio characteristics ETSI EN 301419-1, EN 301511

Caller line identification presentation (CLIP) ETSI EN 300 089 V3.1.(2000-12)

Can be operated according to commission decision 2000/299/EC

Hereby, Jablotron Ltd., declares that this JA-60GSM is

in compliance with the essential requirements and

other relevant provisions of Directive 1999/5/EC.

Original of the conformity assessment can be found at the web page

www.jablotron.cz, section Technical support.

Note: Although this product does not contain any harmful materials we

suggest you to return the product to the dealer or directly to the

producer after usage.

JA-60GSM dialer module 11 / 11 MFJ51215

11 Brief list of programming sequences

Function Sequence Options Factory default

Tel. numbers for SMS and audible

reports

7t xxx..x F0

t = memory from 1 to 8

xxxx = tel. number (max.20 digits), F9=”+”

blank

Event SMS reports 81 uu t y

Event acoustic reports 82 uu t y

uu = events index from 01 to 31

t = memory from 1 to 8

y=0 disabled, y=1 enabled

t=1&2 alarm SMS

t=3&4 alarm SMS + audible

t=5&6 alarm+arming SMS + audible

t=7&8 audible alarm only

SMS and audible reports SW 80 y

y=0 disabled, y=1 enabled, y=2 (enabled with

restrictions)

enabled

GSM signal checking 91 y y=0 disabled, y=1 enabled disabled

Incoming call reaction 93 x

x = 0 no reaction

x = 1 to 8 answer after 5 to 40 seconds

x = 9 answer after the 1

ring of the 2

call

after 25 seconds

Service remote access code 94 xxxxxxxx F0

xxxxxxxxx = code, it can have form 1 to 8 digits

deleting - 94F0 - remote access is not possible

0000

User remote access code 94 xxxxxxxx F1

xxxxxxxxx = code, it can have from 1 to 8 digits

deleting 94F1 - remote access is not possible

1111

Confirmation SMS reply 95 y

y=0 disabled, y=1 enabled

if disabled, end instruction with C to get the reply

enabled

Reset 96060 Reset to factory default settings

Reset & no reports 96061 Reset to factory default settings & all reports disabled

Immediate codeless dialing-in 970 If entered while in programming, you can dial-in after the 1

ring without the access code

Measuring of GSM signal 971 If entered while in programming, it shows GSM signal strength (from 0 to 9)

Volume adjustment of the

connected phone

974x

975x

Level adjustment of received and outgoing signal

(from 1 to 9)

5 – medium level

GSM Module Reset 976

If entered while in programming mode, the GSM module will be disconnected from and

connected to the GSM network.

It is also possible to send the command via SMS in the

form yyyyy*GSM.

Language setting 977 xx

xx=01 to 16 where: 01=EN, 02=CZ, 03=SK, 04=DA,

05=FI, 06=DE, 07=HU, 08=IT, 09=PL, 10=PT,

11=RU, 12=SE, 13=TR, 14=ES, 15=NL, 16=CN

English

Attached phone function 98 y

y=0 telephone line y=2 no function

y=1 alarm keypad y=3 emergency call

telephone line

Emergency call number 99 xxxxxx F0 xxxxxx = tel. number (max.20 digits), F9=”+” erased

CMS telephone numbers 0y p xxxxx F0

y=1 primary number, y=2 back up number

p=1 CMS1, p=2 CMS2

xxxx = tel. number (max.20 digits), F9=”+”

all erased

Account ID 03 p zzzz F0

p=1 CMS1, p=2 CMS2

zzzz account ID, z=0 to 9 or A=F1, B=F2, C=F3,

D=F4, E=F5 and F=F6

0000 for both CMSs

CMS protocol 04 p x

p=1 CMS1, p=2 CMS2

x=0 CID, x=1 SMS, x=2 GPRS

CID for both CMSs

Events to report 05 p uu y

p=1 CMS1, p=2 CMS2

uu = events index from 01 to 31

y=0 disabled, y=1 enabled

all reports disabled

CMS redialing pause 06 p t

p=1 CMS1, p=2 CMS2

t=1 to 9 (x 5minutes)

5 minutes

Periodic test interval 07 p hh mm

p=1 CMS1, p=2 CMS2

hh mm hours minutes

24hr. after the last report

CMS reports SW 00 p y

p=1 CMS1, p=2 CMS2

y=0 disabled, y=1 enabled

disabled for both CMSs

CMS2 as a backup of CMS1 08 y

y=0 two independent CMS

y=1 CMS2 is a back up for CMS1

two independent CMS

Storing the event “data to CMS

sent” into the event list

09 y y=0 ... disable , y=1 ... enable Enable

Jablotron JA-60GSM Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Jablotron JA-60GSM

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info